Add dma mode support for LPSPI. Any frame longer than half txfifosize will
be sent by dma mode.

For now, there are some limits:
1. The maximum transfer speed in master mode depends on the slave device,
   at least 40MHz(tested by spi-nor on 8qm-lpddr4-arm2 base board);
2. The maximum transfer speed in slave mode is 15MHz(imx7ulp),
   22MHz(8qm/qxp). In order to reach the maximum speed which is mentioned
   in datasheet, the load of connect wires between master and slave
   should be less than 15pF.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the default implementation of transfer_one_msg/chipselect/setup
functions in spi core to implement cs-gpio control.
Use fsl_lpspi_prepare_message to init the cs_gpio pin.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a error info when set a speed which greater than half of per-clk of
spi module.

The minimum SCK period is 2 cycles(CCR[SCKDIV]). So the maximum transfer
speed is half of spi per-clk.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable the runtime power management for lpspi module.

Do some adaptation work from kernel 4.9 to 4.14.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add introductions of clocks and clock-names strings.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add both ipg and per clock for lpspi to support i.MX8QM/QXP boards.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds suspend and resume support for spi-stm32-qspi
drivers.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch solves a memory corruption seen at 8 MHz.
To avoid such issue, timeout counter is disabled.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

While the sequencer is reset after each SPI message since commit
880c6d11 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.

Fix this by initializing it explicitly during configuration.

Fixes: 0b2182dd ("spi: add support for Renesas RSPI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Renesas RSPI/QSPI driver performs SPI controller register
initialization in its spi_operations.setup() callback, without calling
pm_runtime_get_sync() first, which may cause spurious failures.

So far this went unnoticed, as this SPI controller is typically used
with a single SPI NOR FLASH containing the boot loader:
  1. If the device's module clock is still enabled (left enabled by the
     bootloader, and not yet disabled by the clk_disable_unused() late
     initcall), register initialization succeeds,
  2. If the device's module clock is disabled, register writes don't
     seem to cause lock-ups or crashes.
     Data received in the first SPI message may be corrupted, though.
     Subsequent SPI messages seem to be OK.
     E.g. on r8a7791/koelsch, one bit is lost while receiving the 6th
     byte of the JEDEC ID for the s25fl512s FLASH, corrupting that byte
     and all later bytes.  But until commit a2126b0a ("mtd:
     spi-nor: refine Spansion S25FL512S ID"), the 6th byte was not
     considered for FLASH identification.

Fix this by moving all initialization from the .setup() to the
.prepare_message() callback.  The latter is always called after the
device has been runtime-resumed by the SPI core.

This also makes the driver follow the rule that .setup() must not change
global driver state or register values, as that might break a transfer
in progress.

Fixes: 490c9774 ("spi: rspi: Add runtime PM support, using spi core auto_runtime_pm")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>

Geert points out that I confused the min/max arguments that are
reversed between SPI_BPW_RANGE_MASK() and GENMASK(). This time
I have verified the result of the macro after fixing the arguments.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: eefffb42 ("spi: work around clang bug in SPI_BPW_RANGE_MASK()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>

The driver does not clearly unregister the spi controller.
Therefore calling an unbind and bind again will end up in a
Kernel crash.

The function devm_spi_register_controller will automatically
be unregister the SPI device.
Signed-off-by: Volker Haspel <volker.haspel@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 71abd290 ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer.  In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.

However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.

Change it to empty the FIFO and throw away the data.  Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.

There is another issue, which affects master mode when switching from
DMA to PIO.  There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner.  I don't know
why this data is unexpectedly in the FIFO.  It's likely there is a
different bug or erratum responsible for that.  But regardless of that,
I think this is proper fix the for bug at hand here.

Fixes: 71abd290 ("spi: imx: Add support for SPI Slave mode")
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add the boolean module parameter "use_dma" to control the use of DMA by
the driver.  There are about two dozen other drivers with a "use_dma"
parameter of some sort.

DMA may allow faster and more efficient transfers than using PIO, but it
also adds overhead for small transfers.

High speed receive operations may be less likely to have issues with
FIFO overflow when using DMA than when using PIO.

The eCSPI appears to insert a 4 bit pause after each word in DMA mode,
not done in PIO mode, which can make DMA transfers 50% slower than PIO.

In some cases DMA may be a net win while in others PIO might be.  It
depends on the application.  So allow DMA to be enabled or disabled at
the driver level.  The default will be to have it enabled when possible.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Clang-8 evaluates both sides of a ?: expression to check for
valid arithmetic even in the side that is never taken. This
results in a build warning:

drivers/spi/spi-sh-msiof.c:1052:24: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
        .bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32),
                              ^~~~~~~~~~~~~~~~~~~~~~~~~

Change the implementation to use the GENMASK() macro that does
what we want here but does not have a problem with the shift
count overflow.

Link: https://bugs.llvm.org/show_bug.cgi?id=38789Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

This fixes a bug for messages containing both zero length and
unidirectional xfers.

The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer.  That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.

Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.

Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.

This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

While the MSIOF variants in older SuperH and SH/R-Mobile SoCs support
bits-per-word values in the full range 8..32, the variants present in
R-Car Gen2 and Gen3 SoCs are restricted to 8, 16, 24, or 32.

Obtain the value from family-specific sh_msiof_chipdata to fix this.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull ARM SoC fixes from Arnd Bergmann:
 "One more set of simple ARM platform fixes:

   - A boot regression on qualcomm msm8998

   - Gemini display controllers got turned off by accident

   - incorrect reference counting in optee"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  tee: optee: add missing of_node_put after of_device_is_available
  arm64: dts: qcom: msm8998: Extend TZ reserved memory area
  ARM: dts: gemini: Re-enable display controller

Pull x86 fixes from Thomas Gleixner:
 "Two last minute fixes:

   - Prevent value evaluation via functions happening in the user access
     enabled region of __put_user() (put another way: make sure to
     evaluate the value to be stored in user space _before_ enabling
     user space accesses)

   - Correct the definition of a Hyper-V hypercall constant"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/hyper-v: Fix definition of HV_MAX_FLUSH_REP_COUNT
  x86/uaccess: Don't leak the AC flag into __put_user() value evaluation

Pull SCSI fixes from James Bottomley:
 "Nine small fixes.

  The resume fix is a cosmetic removal of a warning with an incorrect
  condition causing it to alarm people wrongly.

  The other eight patches correct a thinko in Christoph Hellwig's DMA
  conversion series. Without it all these drivers end up with 32 bit DMA
  masks meaning they bounce any page over 4GB before sending it to the
  controller.

  Nowadays, even laptops mostly have memory above 4GB, so this can lead
  to significant performance degradation with all the bouncing"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: Avoid that system resume triggers a kernel warning
  scsi: hptiop: fix calls to dma_set_mask()
  scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
  scsi: csiostor: fix calls to dma_set_mask_and_coherent()
  scsi: bfa: fix calls to dma_set_mask_and_coherent()
  scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
  scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
  scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
  scsi: lpfc: fix calls to dma_set_mask_and_coherent()

Pull networking fixes from David Miller:

 1) Fix refcount leak in act_ipt during replace, from Davide Caratti.

 2) Set task state properly in tun during blocking reads, from Timur
    Celik.

 3) Leaked reference in DSA, from Wen Yang.

 4) NULL deref in act_tunnel_key, from Vlad Buslov.

 5) cipso_v4_erro can reference the skb IPCB in inappropriate contexts
    thus referencing garbage, from Nazarov Sergey.

 6) Don't accept RTA_VIA and RTA_GATEWAY in contexts where those
    attributes make no sense.

 7) Fix hung sendto in tipc, from Tung Nguyen.

 8) Out-of-bounds access in netlabel, from Paul Moore.

 9) Grant reference leak in xen-netback, from Igor Druzhinin.

10) Fix tx stalls with lan743x, from Bryan Whitehead.

11) Fix interrupt storm with mv88e6xxx, from Hein Kallweit.

12) Memory leak in sit on device registry failure, from Mao Wenan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  net: sit: fix memory leak in sit_init_net()
  net: dsa: mv88e6xxx: Fix statistics on mv88e6161
  geneve: correctly handle ipv6.disable module parameter
  net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
  bpf: fix sanitation rewrite in case of non-pointers
  ipv4: Add ICMPv6 support when parse route ipproto
  MIPS: eBPF: Fix icache flush end address
  lan743x: Fix TX Stall Issue
  net: phy: phylink: fix uninitialized variable in phylink_get_mac_state
  net: aquantia: regression on cpus with high cores: set mode with 8 queues
  selftests: fixes for UDP GRO
  bpf: drop refcount if bpf_map_new_fd() fails in map_create()
  net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
  net: dsa: mv88e6xxx: Fix u64 statistics
  xen-netback: don't populate the hash cache on XenBus disconnect
  xen-netback: fix occasional leak of grant ref mappings under memory pressure
  sctp: chunk.c: correct format string for size_t in printk
  net: netem: fix skb length BUG_ON in __skb_to_sgvec
  netlabel: fix out-of-bounds memory accesses
  ipv4: Pass original device to ip_rcv_finish_core
  ...

Pull more crypto fixes from Herbert Xu:
 "This fixes a couple of issues in arm64/chacha that was introduced in
  5.0"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: arm64/chacha - fix hchacha_block_neon() for big endian
  crypto: arm64/chacha - fix chacha_4block_xor_neon() for big endian

If register_netdev() is failed to register sitn->fb_tunnel_dev,
it will go to err_reg_dev and forget to free netdev(sitn->fb_tunnel_dev).

BUG: memory leak
unreferenced object 0xffff888378daad00 (size 512):
  comm "syz-executor.1", pid 4006, jiffies 4295121142 (age 16.115s)
  hex dump (first 32 bytes):
    00 e6 ed c0 83 88 ff ff 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
backtrace:
    [<00000000d6dcb63e>] kvmalloc include/linux/mm.h:577 [inline]
    [<00000000d6dcb63e>] kvzalloc include/linux/mm.h:585 [inline]
    [<00000000d6dcb63e>] netif_alloc_netdev_queues net/core/dev.c:8380 [inline]
    [<00000000d6dcb63e>] alloc_netdev_mqs+0x600/0xcc0 net/core/dev.c:8970
    [<00000000867e172f>] sit_init_net+0x295/0xa40 net/ipv6/sit.c:1848
    [<00000000871019fa>] ops_init+0xad/0x3e0 net/core/net_namespace.c:129
    [<00000000319507f6>] setup_net+0x2ba/0x690 net/core/net_namespace.c:314
    [<0000000087db4f96>] copy_net_ns+0x1dc/0x330 net/core/net_namespace.c:437
    [<0000000057efc651>] create_new_namespaces+0x382/0x730 kernel/nsproxy.c:107
    [<00000000676f83de>] copy_namespaces+0x2ed/0x3d0 kernel/nsproxy.c:165
    [<0000000030b74bac>] copy_process.part.27+0x231e/0x6db0 kernel/fork.c:1919
    [<00000000fff78746>] copy_process kernel/fork.c:1713 [inline]
    [<00000000fff78746>] _do_fork+0x1bc/0xe90 kernel/fork.c:2224
    [<000000001c2e0d1c>] do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290
    [<00000000ec48bd44>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<0000000039acff8a>] 0xffffffffffffffff
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c39 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.

Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.

This is the same fix as what commit d074bf96 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.

Note there's also commit c0a47e44 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2019-03-01

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) fix sanitation rewrite, from Daniel.

2) fix error path on map_new_fd, from Peng.

3) fix icache flush address, from Paul.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.

Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.

v2:
- add small helper and init the number of actual ports only

Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek reported that he saw an issue with the below snippet in that
timing measurements where off when loaded as unpriv while results
were reasonable when loaded as privileged:

    [...]
    uint64_t a = bpf_ktime_get_ns();
    uint64_t b = bpf_ktime_get_ns();
    uint64_t delta = b - a;
    if ((int64_t)delta > 0) {
    [...]

Turns out there is a bug where a corner case is missing in the fix
d3bd7413 ("bpf: fix sanitation of alu op with pointer / scalar
type from different paths"), namely fixup_bpf_calls() only checks
whether aux has a non-zero alu_state, but it also needs to test for
the case of BPF_ALU_NON_POINTER since in both occasions we need to
skip the masking rewrite (as there is nothing to mask).

Fixes: d3bd7413 ("bpf: fix sanitation of alu op with pointer / scalar type from different paths")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Reported-by: Arthur Fabre <afabre@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/netdev/CAJPywTJqP34cK20iLM5YmUMz9KXQOdu1-+BZrGMAGgLuBWz7fg@mail.gmail.com/T/Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.

Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.

v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.

The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.

Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9 ("MIPS: Add missing file for eBPF JIT.")
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)

The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.

This fix corrects the problem by properly marking the end of
a multi descriptor transmission.

Fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.

v2:
- use right function name in subject
v3:
- initialize additional fields

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.

This patch sets a tx hw traffic mode with 8 queues.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651

Fixes: 71a963cf ("net: aquantia: increase max number of hw queues")
Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.

Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.

Fixes: 3327a9c4 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IOMMU fix from Joerg Roedel:
 "One important fix for a memory corruption issue in the Intel VT-d
  driver that triggers on hardware with deep PCI hierarchies"

* tag 'iommu-fix-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/dmar: Fix buffer overflow during PCI bus notification

Merge misc fixes from Andrew Morton:
 "2 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  hugetlbfs: fix races and page leaks during migration
  kasan: turn off asan-stack for clang-8 and earlier