- 15 Apr, 2017 20 commits
-
-
Niklas Söderlund authored
The HGT is a Histogram Generator Two-Dimensions. It computes a weighted frequency histograms for hue and saturation areas over a configurable region of the image with optional subsampling. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Niklas Söderlund authored
The format is used on the R-Car VSP1 video queues that carry 2-D histogram statistics data. Signed-off-by:
-
Laurent Pinchart authored
The HGO is a Histogram Generator One-Dimension. It computes per-channel histograms over a configurable region of the image with optional subsampling. Signed-off-by:
-
Laurent Pinchart authored
The format is used on the R-Car VSP1 video queues that carry 1-D histogram statistics data. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Laurent Pinchart authored
The addresses are incorrect, fix them. Signed-off-by:
-
Laurent Pinchart authored
Histogram generators are single-pad entities that branch as leaf nodes at any point in the pipeline. Make sure that pipeline traversal and routing configuration support them correctly. Support for the actual HGO and HGT operation will come later. Signed-off-by:
-
Laurent Pinchart authored
The histogram common code will be used to implement support for both the HGO and HGT histogram computation engines. Signed-off-by:
-
Laurent Pinchart authored
The metadata buffer type is used to transfer metadata between userspace and kernelspace through a V4L2 buffers queue. It comes with a new metadata capture capability and format description. Signed-off-by:
Guennadi Liakhovetski <guennadi.liakhovetski@intel.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> [hans.verkuil@cisco.com: removed left-over 'experimental' note] [hans.verkuil@cisco.com: add newline after _v4l2-meta-format label] Signed-off-by:
-
Laurent Pinchart authored
Some WPF instances, on Gen3 devices, can perform 90° rotation when writing frames to memory. Implement support for this using the V4L2_CID_ROTATE control. Signed-off-by:
-
Laurent Pinchart authored
V4L2 exposes parameters that influence buffers sizes through the format ioctls (VIDIOC_G_FMT, VIDIOC_TRY_FMT, VIDIOC_S_FMT, and possibly VIDIOC_G_SELECTION and VIDIOC_S_SELECTION). Other parameters not part of the format structure may also influence buffer sizes or buffer layout in general. One existing such parameter is rotation, which is implemented by the V4L2_CID_ROTATE control and thus exposed through the V4L2 control ioctls. The interaction between those parameters and buffers is currently only partially specified by the V4L2 API. In particular interactions between controls and buffers isn't specified at all. The behaviour of the VIDIOC_S_FMT and VIDIOC_S_SELECTION ioctls when buffers are allocated is also not fully specified. This patch clearly defines and documents the interactions between formats, selections, controls and buffers. The preparatory discussions for the documentation change considered completely disallowing controls that change the buffer size or layout, in favour of extending the format API with a new ioctl that would bundle those controls with format information. The idea has been rejected, as this would essentially be a restricted version of the upcoming request API that wouldn't bring any additional value. Another option we have considered was to mandate the use of the request API to modify controls that influence buffer size or layout. This has also been rejected on the grounds that requiring the request API to change rotation even when streaming is stopped would significantly complicate implementation of drivers and usage of the V4L2 API for applications. Applications will however be required to use the upcoming request API to change at runtime formats or controls that influence the buffer size or layout, because of the need to synchronize buffers with the formats and controls. Otherwise there would be no way to interpret the content of a buffer correctly. Signed-off-by:
-
Hans Verkuil authored
Simplify ov2640_set_params and ov2640_set_fmt. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Hans Verkuil authored
Simplify ov9740_s_fmt. Signed-off-by:
-
Hans Verkuil authored
Simplify ov9640_s_fmt and ov9640_set_fmt Signed-off-by:
-
Hans Verkuil authored
Merge ov772x_s_fmt into ov772x_set_fmt. Signed-off-by:
-
Hans Verkuil authored
Simplify ov5642_set_fmt(). Signed-off-by:
-
Hans Verkuil authored
Simplify mt9v022_s_fmt and mt9v022_set_fmt. Signed-off-by:
-
Hans Verkuil authored
Simplify mt9m001_s_fmt and mt9m001_set_fmt. Signed-off-by:
-
Hans Verkuil authored
Simplify imx074_set_fmt(). Signed-off-by:
-
Stefan Brüns authored
The Si2141 needs two distinct commands for powerup/reset, otherwise it will not respond to chip revision requests. It also needs a firmware to run properly. Cc: Evgeny Plehov <EvgenyPlehov@ukr.net> Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
'Reset' loop does not look correct. I tested it very many times and it never repeated those commands. If problem, it tries to solve, really occurs on some situations better solution should be find out. There is another patch which does not have such hackish looking loop. Lets change to it. Cc: Evgeny Plehov <EvgenyPlehov@ukr.net> Signed-off-by:
-
- 10 Apr, 2017 20 commits
-
-
Hans Verkuil authored
The XV601/709 encodings are special: they signal limited range, but use the full range to encode a larger gamut with R', G' and B' values outside the [0-1] range. So don't clamp to limited range for these two encodings. Signed-off-by:
-
Hans Verkuil authored
The XV601/709 Y'CbCr encoding was changed to limited range, but the comment still indicates full range. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
Geliang Tang <geliangtang@gmail.com> Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by:
-
Nikola Jelic authored
Some of the macros didn't use the parenthesis around the parameters when used in the body of the macro. Signed-off-by:
Nikola Jelic <nikola.jelic83@gmail.com> Signed-off-by:
-
Alexey Khoroshilov authored
If DMA does not support INTERLEAVE, deinterlace_probe() breaks off initialization, releases dma channel, but returns zero. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Philipp Zabel authored
TRY_FMT already disables the YUYV format if the VDOA is not available. ENUM_FMT must do the same. Fixes: d40e98c1 ("[media] coda: support YUYV output if VDOA is used") Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height values in struct v4l2_mbus_framefmt still refer to frame size, not field size. Fixes: 4f57d27b ("[media] tvp5150: fix tvp5150_fill_fmt()") Signed-off-by:
-
Philipp Zabel authored
To let userspace propagate formats downstream in a media controller scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow setting and getting the format. Incidentally, tvp5150_fill_fmt was implemented for this pad, not for the new analog input pad (now pad 0, DEMOD_PAD_IF_INPUT). Fixes: 55606310 ("[media] tvp5150: create the expected number of pads") Signed-off-by:
-
Colin Ian King authored
The call to v4ls_m2m_get_vq is only used to get the return value which is not being used, so it appears to be redundant and can be removed. Detected with CoverityScan, CID#1420674 ("Useless call") Signed-off-by:Colin Ian King <colin.king@canonical.com> Acked-by:
-
Hans Verkuil authored
The em28xx driver still used the soc_camera.h header for the ov2640 driver. Since this driver no longer uses soc_camera, that include can be removed. Signed-off-by:
-
