Add both PCIe3 controllers together with the shared PHY.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230717173512.65169-3-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

add alias for sdmmc as mmc1.
make card detect work.

Fixes: ea3e66e7 ("arm64: dts: rockchip: add SD card support to rock-5a")
Fixes: 2a6d4af5 ("arm64: dts: rockchip: Add SD card support to rock-5b")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20230722121150.130126-1-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model A.
This adds USB support for the on-board WLAN/BT chip, the two USB2
ports, the USB available from the 2x20 connector and the lower USB3
port (in USB2 mode).

The upper USB3 (further away from the PCB) uses the RK3588S USB TypeC
OTG controller for USB2 and USB3 and thus is not supported at all at
the moment.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-5-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model B.
This adds USB support on the M.2 Key E, both USB2 ports and USB2 mode
for the upper USB3 port (the one further away from the PCB).

The lower USB3 (closer to the PCB) and the USB-C ports use the RK3588
USB TypeC host controller, which is not yet supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-4-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Rockchip RK3588 EVB1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-3-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds USB2 (EHCI & OHCI) ports including the related PHYs
and GRF modules to the rk3588(s) device tree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-2-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RS485 support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-8-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RS232 support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-7-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add PWM FAN support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-6-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RTC support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-5-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add SATA support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-3-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add sdmmc support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-2-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds PMIC support for the Edgeble Neu6B NCM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-1-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the SATA0_0 port found on the RK3588 EVB1. The
second port (SATA0_1) does not work, which matches the downstream
behaviour.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230711171330.52535-1-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add all three SATA IP blocks to the RK3588 DT.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230612171337.74576-6-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add all 3 combo PHYs that can be found in RK3588.
They are used for SATA, PCIe or USB3.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230612171337.74576-5-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add dts for Firefly Station P2.
Working IO:
* eMMC
* HDMI
* LAN
* LED
* SD Card
* UART
* USB2
* USB3
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Link: https://lore.kernel.org/r/20230620184746.55391-3-f.kardame@manjaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Station P2 is a single board computer by firefly based
on rk3568 soc
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230620184746.55391-2-f.kardame@manjaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

200MHz is the default rk3588 emmc max-frequency added in dtsi, so why
the board DT files are adding the same value explicitly?

Drop that unchanged property value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230621064507.479891-1-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add board-specific devicetree file for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-4-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree binding entry for the Radxa ROCK 4SE.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-3-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The ROCK 4SE uses the RK3399-T variant of the RK3399 SoC, which has some
changes to the OPP tables. Prepare for the bringup of this SoC by moving
the inclusion of existing OPP tables from the common devicetree into
each board-specific devicetree.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-2-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the necessary DT changes for the Rock 5A board to enable support for
the PWM controlled heat sink fan.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-14-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable ADC support for Rock 5A, which has the following ADC channels:

Channel 0 = Boot Mode Config
Channel 1 = Recovery Key
Channel 2 = PWM Fan
Channel 3 = Headphone Hook
Channel 4 = System Input Voltage
Channel 5 = Board ID Config
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-13-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

I2C3 is routed to the Camera connector and I2C5 is routed to the LCD
connector. On I2C5 additionally there is an unpopulated footprint for
a HYM8563TS RTC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-12-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the NPU regulator.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-11-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the I2C EEPROM to the Rock 5A DT.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-10-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add analog audio support based on the Everest Semi ES8316 codec.

Note, that this currently does not support headphone plug events. The
Rock 5A uses a different headphone jack with a different logic to detect
a headphone plug. Unfortunately the detect GPIO is always low.
Downstream uses an ADC channel instead, but that is currently not
supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-9-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Describe the Rock 5A status LED in its device tree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-8-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add sdmmc support for Rock Pi 5A board.
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-7-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add GPIO controlled 5V regulator, which is used for supplying
the fan, on-board USB hub and HDMI.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-6-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The RK8602 and RK8603 voltage regulators on the Rock 5A board provide
the power lines vdd_cpu_big0 and vdd_cpu_big1, respectively.

Add the necessary device tree nodes and bind them to the corresponding
CPU big core nodes.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-5-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds PMIC support for the Radxa ROCK 5A
Co-developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-4-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add binding for Belling BL24C16A, which is compatible with Atmel 24C16.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230710165228.105983-3-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add a vendor prefix entry for belling (https://www.belling.com.cn)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230710165228.105983-2-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The audio-graph-card driver uses the 'label' property to register the
sound card in the system, but the currently assigned string is too
generic and cannot be supported by alsa-project/alsa-ucm-conf:

  card 0: Analog [Analog]

Use the more specific naming "rk3588-es8316", which is still generic
enough to be shared with other compatible boards, e.g. Rock 5A. The
audio card will be listed as:

  card 0: rk3588es8316 [rk3588-es8316]

While at it, update also the DT node name, as there will be additional
sound related nodes available, i.e. for HDMI. Note that this involves
moving the node one position up, to preserve the alphabetical order.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230707162822.676024-1-cristian.ciocaltea@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add dtsi entry for RK3399 PCIe endpoint core in the device tree.
The status is "disabled" by default, so it will not be loaded unless
explicitly chosen to. The RK3399 PCIe endpoit core should be enabled
with the RK3399 PCIe root complex disabled because the RK3399 PCIe
controller can only work one mode at the time, either in "root complex"
mode or in "endpoint" mode.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Link: https://lore.kernel.org/r/20230418074700.1083505-6-rick.wertenbroek@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool