- 10 Apr, 2021 12 commits
-
-
Linus Walleij authored
When I test to use the CY8CTMA340 with PostmarketOS I don't have any problem whatsoever in dropping this phys path, it finds and uses the touchscreen just as well. I suppose it is because userspace is using modern input libraries. I challenge the maintainers to point out a valid and still used userspace that actually need this. I say we drop it. Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210408131153.3446138-7-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Linus Walleij authored
The data sheet for CY8CTMA340 specifies that the reset pulse shall be at least 1 ms. Specify 1-2 ms with usleep_range() to cut some slack for the scheduler. Curiously the datasheet does not specify how long we have to wait after a hard reset until the chip is up, but I have found a vendor tree (Samsung GT-S7710) that has code for this touch screen and there this is set to 5 ms so I use this with the same 1 ms fuzz. Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210408131153.3446138-6-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Linus Walleij authored
Provide a proper error message when attempting to exit boot loader mode and failing, which is something that happened to me. Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210408131153.3446138-5-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jiapeng Chong authored
Fix the following gcc warning: drivers/input/serio/apbps2.c:106:16: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/1617958859-64707-1-git-send-email-jiapeng.chong@linux.alibaba.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Linus Walleij authored
The Melfas MMS136 is similar to the other MMS variants but has event packages of 6 bytes rather than 8 as the others. The define is named FINGER_EVENT_SZ in the vendor drivers so I renamed it from MMS*_PACKET_SZ to MMS*_EVENT_SZ. After this patch, the touchscreen on the Samsung GT-I8530 works fine with PostmarketOS. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210404232619.3092682-1-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Linus Walleij authored
This converts the Melfas MMS114 bindings and extend like this: - Require nodename touchscreen@ (this seems to be the case for all in-tree DTS files) - Add the mms134s and mms136 compatibles - Add the avdd and vdd power supplies - Define the I2C clock frequency property Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210330201233.2360006-1-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Joe Hung authored
Add support for ILITEK Lego series of touch devices. Lego series includes ILITEK 213X/23XX/25XX. Tested/passed with evaluation board with ILI2520/2322 IC. Signed-off-by: Joe Hung <joe_hung@ilitek.com> Link: https://lore.kernel.org/r/20210324122601.125873-2-joe_hung@ilitek.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Joe Hung authored
Add binding documentation for ILITEK touch devices. Signed-off-by: Joe Hung <joe_hung@ilitek.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210324122601.125873-1-joe_hung@ilitek.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Vincent Knecht authored
Add support for the msg2638 touchscreen IC from MStar. Firmware handling, wakeup gestures and other specialties are not supported. This driver reuses zinitix.c structure, while the checksum and irq handler functions are based on out-of-tree driver for Alcatel Idol 3 (4.7"). Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210305153815.126937-2-vincent.knecht@mailoo.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Vincent Knecht authored
This adds dts bindings for the mstar msg2638 touchscreen. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210305153815.126937-1-vincent.knecht@mailoo.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Some buggy BIOS-es bring up the touchscreen-controller in a stuck state where it blocks the I2C bus. Specifically this happens on the Jumper EZpad 7 tablet model. After much poking at this problem I have found that the following steps are necessary to unstuck the chip / bus: 1. Turn off the Silead chip. 2. Try to do an I2C transfer with the chip, this will fail in response to which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first drop the chip of the bus by turning it off. 3. Turn the chip back on. On the x86/ACPI systems were this problem is seen, step 1. and 3. require making ACPI calls and dealing with ACPI Power Resources. This commit adds a workaround which runtime-suspends the chip to turn it off, leaving it up to the ACPI subsystem to deal with all the ACPI specific details. There is no good way to detect this bug, so the workaround gets activated by a new "silead,stuck-controller-bug" boolean device-property. Since this is only used on x86/ACPI, this will be set by model specific device-props set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new device-property is not documented in the DT-bindings. Dmesg will contain the following messages on systems where the workaround is activated: [ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error [ 55.373593] i2c_designware 808622C1:04: controller timed out [ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Several users have been reporting that elants_i2c gives several errors during probe and that their touchscreen does not work on their Lenovo AMD based laptops with a touchscreen with a ELAN0001 ACPI hardware-id: [ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator [ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator [ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121 [ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121 [ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121 [ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121 [ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121 [ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121 [ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121 [ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121 [ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff [ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121 [ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff Despite these errors, the elants_i2c driver stays bound to the device (it returns 0 from its probe method despite the errors), blocking the i2c-hid driver from binding. Manually unbinding the elants_i2c driver and binding the i2c-hid driver makes the touchscreen work. Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid compatiblity-id strings and if it has the I2C-HID spec's DSM to get the HID descriptor address, If it has both then make elants_i2c not bind, so that the i2c-hid driver can bind. This assumes that non of the (older) elan touchscreens which actually need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id + DSM in their ACPI-fwnodes. If some of them actually do have this false advertising, then this change may lead to regressions. While at it also drop the unnecessary DEVICE_NAME prefixing of the "I2C check functionality error", dev_err already outputs the driver-name. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 08 Apr, 2021 1 commit
-
-
Dmitry Torokhov authored
My brain-damaged adjustments to Paul's patch caused crashes in gpio_keys_disable_button() when driver is used in GPIO-less (i.e. purely interrupt-driven) setups, because I mixed together debounce and release timers when they are in fact separate: Unable to handle kernel NULL pointer dereference at virtual address 0000000c ... PC is at hrtimer_active+0xc/0x98 LR is at hrtimer_try_to_cancel+0x24/0x140 ... [<c01c43b8>] (hrtimer_active) from [<c01c50f4>] (hrtimer_try_to_cancel+0x24/0x140) [<c01c50f4>] (hrtimer_try_to_cancel) from [<c01c5224>] (hrtimer_cancel+0x14/0x4c) [<c01c5224>] (hrtimer_cancel) from [<bf1cae24>] (gpio_keys_attr_store_helper+0x1b8/0x1d8 [gpio_keys]) [<bf1cae24>] (gpio_keys_attr_store_helper [gpio_keys]) from [<bf1cae80>] (gpio_keys_store_disabled_keys+0x18/0x24 [gpio_keys]) [<bf1cae80>] (gpio_keys_store_disabled_keys [gpio_keys]) from [<c038ec7c>] (kernfs_fop_write_iter+0x10c/0x1cc) [<c038ec7c>] (kernfs_fop_write_iter) from [<c02df858>] (vfs_write+0x2ac/0x404) [<c02df858>] (vfs_write) from [<c02dfaf4>] (ksys_write+0x64/0xdc) [<c02dfaf4>] (ksys_write) from [<c0100080>] (ret_fast_syscall+0x0/0x58) Let's fix it up. Fixes: c9efb0ba ("Input: gpio-keys - use hrtimer for software debounce, if possible") Reported-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/YG1DFFgojSVfdpaz@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 28 Mar, 2021 1 commit
-
-
Fabio Estevam authored
i.MX has been converted to a DT-only platform, so make the adjustments to the driver to convert it to a DT-only driver. Signed-off-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210327194307.541248-1-festevam@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 25 Mar, 2021 25 commits
-
-
Nikolai Kostrigin authored
s/max_baseliune/max_baseline/ Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org> Link: https://lore.kernel.org/r/20210311114146.1977616-1-nickel@altlinux.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Barry Song authored
disable_irq() after request_irq() still has a time gap in which interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable because of requesting. On the other hand, request_irq() after setting IRQ_NOAUTOEN as below irq_set_status_flags(irq, IRQ_NOAUTOEN); request_irq(dev, irq...); can also be replaced by request_irq() with IRQF_NO_AUTOEN flag. Signed-off-by: Barry Song <song.bao.hua@hisilicon.com> Link: https://lore.kernel.org/r/20210302224916.13980-3-song.bao.hua@hisilicon.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dmitry Torokhov authored
Merge tag 'irq-no-autoen-2021-03-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next Sync up with the tip tree to pick up IRQF_NO_AUTOEN.
-
Dmitry Torokhov authored
Sync up with the mainline to bring in newest APIs.
-
Linus Walleij authored
The first thing the Cypress driver does when starting up is to try a soft reset. This is the first point where the driver SPI/I2C communication can fail, so put out some nice debug text: cyttsp-spi spi2.0: failed to send soft reset Instead of just: cyttsp-spi: probe of spi2.0 failed with error -5 This is more helpful. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210322221349.1116666-1-linus.walleij@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
This patch converts the legacy text-based binding document to YAML format. Extraneous details and touchscreen properties that weren't actually supported have been dropped. The reset GPIO has since been made optional in the driver; this is now reflected here as well. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210323021006.367-2-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
The device's hardware reset pin is only required if the platform must be able to update the device's firmware. As such, demote the reset GPIO to optional in support of devices that ship with pre-programmed firmware and don't route the reset pin back to the SoC. In that case, the 'fw_file' attribute is hidden because there is no way to open the bootloader. The logic is extended to the case in which the device does not advertise bootloader support in the first place. Last but not least, remove the hardware reset performed at probe because there is no reason to reset the device manually. A power on reset function already ensures a clean reset at start-up. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210323021006.367-1-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
This patch adds support for the Azoteq IQS626A capacitive touch controller. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210301234928.4298-5-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
This patch adds device tree bindings for the Azoteq IQS626A capacitive touch controller. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210301234928.4298-4-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
Now that the helper functions have been moved to drivers/input/ so that all input devices may use them, the introductory comments can be updated to remove any implication that the helper functions are solely limited to touchscreens. This patch also scrubs any remaining use of 'DT' since there isn't any actual dependency on OF. A minor spelling error is resolved as well ('setups' -> 'sets up'). Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210301234928.4298-3-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
Some devices outside of drivers/input/touchscreen/ can still make use of the touchscreen helper functions. Therefore, it was agreed in [1] to move them outside of drivers/input/touchscreen/ so that other devices can call them without INPUT_TOUCHSCREEN being set. As part of this change, 'of' is dropped from the filename because the helpers no longer actually use OF. No changes are made to the file contents whatsoever. Based on the feedback in [2], the corresponding binding documents (touchscreen.yaml and touchscreen.txt) are left in their original locations. [1] https://patchwork.kernel.org/patch/11924029/ [2] https://patchwork.kernel.org/patch/12042037/Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210301234928.4298-2-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dmitry Torokhov authored
This simplifies error unwinding path and allows us to get rid of remove() method. Reviewed-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/20210321220043.318239-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dmitry Torokhov authored
Instead of forcing interrupt trigger to "level low" rely on the platform to set it up according to how it is wired on the given board. Reviewed-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/20210321220043.318239-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
The bootloader can be closed using the 'execute' command (0x02) or hardware reset. Rather than using the former option for successful firmware update procedures and reserving the latter for recovering the device upon failure, simply use hardware reset for all cases. The post-bootloader initialization delay increases marginally when triggered by a hardware reset, so increase the wait time to ensure the device does not subsequently fail to respond. As part of this change, refactor the return path to avoid an extra assignment and to make the logic a bit smaller. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210313191236.4366-6-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
The vendor-assigned firmware project number is restricted to the generic project number (15); however the vendor may assign other project numbers to specific applications and customers. These custom project numbers may be based on forwards-compatible firmware revision 1.x. However, the driver unnecessarily rejects anything older than firmware revision 2.0. To support other applications, remove these unnecessarily strict checks and enter the bootloader only for truly incompatible A000 devices. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210313191236.4366-5-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
Add the read-only 'fw_info' attribute which reports information about the device's firmware in the following format: a.b.c.d:e.f Where: a = Product number (e.g. 40 for IQS550) b = Project number (e.g. 15) c = Firmware revision (major) d = Firmware revision (minor) e = Customer-assigned exported file version (major) f = Customer-assigned exported file version (minor) As part of the corresponding rework to uses of 'bl_status', the IQS5XX_BL_STATUS_RESET definition is dropped with 0 used in its place instead. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210313191236.4366-4-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
Set the maximum ABS_MT_PRESSURE value and use the existing U16_MAX definition instead of a magic number to validate ABS_MT_POSITION_X and ABS_MT_POSITION_Y. Also use input_set_abs_params() rather than input_abs_set_max() to avoid having to call input_set_capability() separately. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210313191236.4366-3-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
Replace 'http' with 'https' and correct the spelling of the nearby word 'datasheet'. Signed-off-by: Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20210313191236.4366-2-jeff@labundy.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Bhaskar Chowdhury authored
s/subsytem/subsystem/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210322022030.3857089-1-unixbhaskar@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Paul Cercueil authored
We want to be able to report the input event as soon as the debounce delay elapsed. However, the current code does not really ensure that, as it uses the jiffies-based schedule_delayed_work() API. With a small enough HZ value (HZ <= 100), this results in some input events being lost, when a key is quickly pressed then released (on a human's time scale). Switching to hrtimers fixes this issue, and will work even on extremely low HZ values (tested at HZ=24). This is however only possible if reading the GPIO is possible without sleeping. If this condition is not met, the previous approach of using a jiffies-based timer is taken. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20210307222240.380583-3-paul@crapouillou.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Paul Cercueil authored
Dealing with input, timing is important; if the button should be released in one millisecond, then it should be done in one millisecond and not a hundred milliseconds. Therefore, the standard timer API is not really suitable for this task. Convert the gpio-keys driver to use a hrtimer instead of the standard timer to address this issue. Note that by using a hard IRQ for the hrtimer callback, we can get rid of the spin_lock_irqsave() and spin_unlock_irqrestore(). Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20210307222240.380583-2-paul@crapouillou.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Paul Cercueil authored
The input_sync() function is already called after the loop in gpio_keys_report_state(), so it does not need to be called after each iteration within gpio_keys_gpio_report_event(). Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20210307222240.380583-1-paul@crapouillou.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Heikki Krogerus authored
The old device property API is about to be removed, so explaing how to use complete software nodes instead. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20210304090948.27014-1-heikki.krogerus@linux.intel.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Krzysztof Kozlowski authored
The touchscreen can be a wake up source and it's being used in DTS: arch/arm/boot/dts/exynos5250-spring.dt.yaml: trackpad@4b: 'wakeup-source' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210212163806.69996-1-krzk@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Uwe Kleine-König authored
The for loop is just a complicate way to express a division. Replace it by the actual division which is both simpler to understand for a human and more efficient for a CPU to calculate. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Link: https://lore.kernel.org/r/20210316212233.50765-1-uwe@kleine-koenig.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 21 Mar, 2021 1 commit
-
-
Linus Torvalds authored
-