When binding a QP with a counter and the QP state is not RESET, return
failure if the rts2rts_qp_counters_set_id is not supported by the
device.

This is to prevent cases like manual bind for Connect-IB devices from
returning success when the feature is not supported.

Fixes: d14133dd ("IB/mlx5: Support set qp counter")
Link: https://lore.kernel.org/r/20200126171708.5167-1-leon@kernel.orgSigned-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Add a check that the size specified in the flow spec header doesn't cause
an overflow when calculating the filter size, and thus prevent access to
invalid memory.  The following crash from syzkaller revealed it.

  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN PTI
  CPU: 1 PID: 17834 Comm: syz-executor.3 Not tainted 5.5.0-rc5 #2
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
  rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
  RIP: 0010:memchr_inv+0xd3/0x330
  Code: 89 f9 89 f5 83 e1 07 0f 85 f9 00 00 00 49 89 d5 49 c1 ed 03 45 85
  ed 74 6f 48 89 d9 48 b8 00 00 00 00 00 fc ff df 48 c1 e9 03 <80> 3c 01
  00 0f 85 0d 02 00 00 44 0f b6 e5 48 b8 01 01 01 01 01 01
  RSP: 0018:ffffc9000a13fa50 EFLAGS: 00010202
  RAX: dffffc0000000000 RBX: 7fff88810de9d820 RCX: 0ffff11021bd3b04
  RDX: 000000000000fff8 RSI: 0000000000000000 RDI: 7fff88810de9d820
  RBP: 0000000000000000 R08: ffff888110d69018 R09: 0000000000000009
  R10: 0000000000000001 R11: ffffed10236267cc R12: 0000000000000004
  R13: 0000000000001fff R14: ffff88810de9d820 R15: 0000000000000040
  FS:  00007f9ee0e51700(0000) GS:ffff88811b100000(0000)
  knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000000 CR3: 0000000115ea0006 CR4: 0000000000360ee0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   spec_filter_size.part.16+0x34/0x50
   ib_uverbs_kern_spec_to_ib_spec_filter+0x691/0x770
   ib_uverbs_ex_create_flow+0x9ea/0x1b40
   ib_uverbs_write+0xaa5/0xdf0
   __vfs_write+0x7c/0x100
   vfs_write+0x168/0x4a0
   ksys_write+0xc8/0x200
   do_syscall_64+0x9c/0x390
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x465b49
  Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89
  f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
  f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
  RSP: 002b:00007f9ee0e50c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000465b49
  RDX: 00000000000003a0 RSI: 00000000200007c0 RDI: 0000000000000004
  RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9ee0e516bc
  R13: 00000000004ca2da R14: 000000000070deb8 R15: 00000000ffffffff
  Modules linked in:
  Dumping ftrace buffer:
     (ftrace buffer empty)

Fixes: 94e03f11 ("IB/uverbs: Add support for flow tag")
Link: https://lore.kernel.org/r/20200126171500.4623-1-leon@kernel.orgSigned-off-by: Avihai Horon <avihaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

When the hfi1 device is shut down during a system reboot, it is possible
that some QPs might have not not freed by ULPs. More requests could be
post sent and a lingering timer could be triggered to schedule more packet
sends, leading to a crash:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
  IP: [ffffffff810a65f2] __queue_work+0x32/0x3c0
  PGD 0
  Oops: 0000 1 SMP
  Modules linked in: nvmet_rdma(OE) nvmet(OE) nvme(OE) dm_round_robin nvme_rdma(OE) nvme_fabrics(OE) nvme_core(OE) pal_raw(POE) pal_pmt(POE) pal_cache(POE) pal_pile(POE) pal(POE) pal_compatible(OE) rpcrdma sunrpc ib_isert iscsi_target_mod target_core_mod ib_iser libiscsi scsi_transport_iscsi ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm mlx4_ib sb_edac edac_core intel_powerclamp coretemp intel_rapl iosf_mbi kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt iTCO_vendor_support mxm_wmi ipmi_ssif pcspkr ses enclosure joydev scsi_transport_sas i2c_i801 sg mei_me lpc_ich mei ioatdma shpchp ipmi_si ipmi_devintf ipmi_msghandler wmi acpi_power_meter acpi_pad dm_multipath hangcheck_timer ip_tables ext4 mbcache jbd2 mlx4_en
  sd_mod crc_t10dif crct10dif_generic mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm mlx4_core crct10dif_pclmul crct10dif_common hfi1(OE) igb crc32c_intel rdmavt(OE) ahci ib_core libahci libata ptp megaraid_sas pps_core dca i2c_algo_bit i2c_core devlink dm_mirror dm_region_hash dm_log dm_mod
  CPU: 23 PID: 0 Comm: swapper/23 Tainted: P OE ------------ 3.10.0-693.el7.x86_64 #1
  Hardware name: Intel Corporation S2600CWR/S2600CWR, BIOS SE5C610.86B.01.01.0028.121720182203 12/17/2018
  task: ffff8808f4ec4f10 ti: ffff8808f4ed8000 task.ti: ffff8808f4ed8000
  RIP: 0010:[ffffffff810a65f2] [ffffffff810a65f2] __queue_work+0x32/0x3c0
  RSP: 0018:ffff88105df43d48 EFLAGS: 00010046
  RAX: 0000000000000086 RBX: 0000000000000086 RCX: 0000000000000000
  RDX: ffff880f74e758b0 RSI: 0000000000000000 RDI: 000000000000001f
  RBP: ffff88105df43d80 R08: ffff8808f3c583c8 R09: ffff8808f3c58000
  R10: 0000000000000002 R11: ffff88105df43da8 R12: ffff880f74e758b0
  R13: 000000000000001f R14: 0000000000000000 R15: ffff88105a300000
  FS: 0000000000000000(0000) GS:ffff88105df40000(0000) knlGS:0000000000000000
  CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000102 CR3: 00000000019f2000 CR4: 00000000001407e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
  Stack:
  ffff88105b6dd708 0000001f00000286 0000000000000086 ffff88105a300000
  ffff880f74e75800 0000000000000000 ffff88105a300000 ffff88105df43d98
  ffffffff810a6b85 ffff88105a301e80 ffff88105df43dc8 ffffffffc0224cde
  Call Trace:
  IRQ

  [ffffffff810a6b85] queue_work_on+0x45/0x50
  [ffffffffc0224cde] _hfi1_schedule_send+0x6e/0xc0 [hfi1]
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffffc0224d62] hfi1_schedule_send+0x32/0x70 [hfi1]
  [ffffffffc0170644] rvt_rc_timeout+0xd4/0x120 [rdmavt]
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffff81097316] call_timer_fn+0x36/0x110
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffff8109982d] run_timer_softirq+0x22d/0x310
  [ffffffff81090b3f] __do_softirq+0xef/0x280
  [ffffffff816b6a5c] call_softirq+0x1c/0x30
  [ffffffff8102d3c5] do_softirq+0x65/0xa0
  [ffffffff81090ec5] irq_exit+0x105/0x110
  [ffffffff816b76c2] smp_apic_timer_interrupt+0x42/0x50
  [ffffffff816b5c1d] apic_timer_interrupt+0x6d/0x80
  EOI

  [ffffffff81527a02] ? cpuidle_enter_state+0x52/0xc0
  [ffffffff81527b48] cpuidle_idle_call+0xd8/0x210
  [ffffffff81034fee] arch_cpu_idle+0xe/0x30
  [ffffffff810e7bca] cpu_startup_entry+0x14a/0x1c0
  [ffffffff81051af6] start_secondary+0x1b6/0x230
  Code: 89 e5 41 57 41 56 49 89 f6 41 55 41 89 fd 41 54 49 89 d4 53 48 83 ec 10 89 7d d4 9c 58 0f 1f 44 00 00 f6 c4 02 0f 85 be 02 00 00 41 f6 86 02 01 00 00 01 0f 85 58 02 00 00 49 c7 c7 28 19 01 00
  RIP [ffffffff810a65f2] __queue_work+0x32/0x3c0
  RSP ffff88105df43d48
  CR2: 0000000000000102

The solution is to reset the QPs before the device resources are freed.
This reset will change the QP state to prevent post sends and delete
timers to prevent callbacks.

Fixes: 0acb0cc7 ("IB/rdmavt: Initialize and teardown of qpn table")
Link: https://lore.kernel.org/r/20200210131040.87408.38161.stgit@awfm-01.aw.intel.comReviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Cleaning up a pq can result in the following warning and panic:

  WARNING: CPU: 52 PID: 77418 at lib/list_debug.c:53 __list_del_entry+0x63/0xd0
  list_del corruption, ffff88cb2c6ac068->next is LIST_POISON1 (dead000000000100)
  Modules linked in: mmfs26(OE) mmfslinux(OE) tracedev(OE) 8021q garp mrp ib_isert iscsi_target_mod target_core_mod crc_t10dif crct10dif_generic opa_vnic rpcrdma ib_iser libiscsi scsi_transport_iscsi ib_ipoib(OE) bridge stp llc iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crct10dif_pclmul crct10dif_common crc32_pclmul ghash_clmulni_intel ast aesni_intel ttm lrw gf128mul glue_helper ablk_helper drm_kms_helper cryptd syscopyarea sysfillrect sysimgblt fb_sys_fops drm pcspkr joydev lpc_ich mei_me drm_panel_orientation_quirks i2c_i801 mei wmi ipmi_si ipmi_devintf ipmi_msghandler nfit libnvdimm acpi_power_meter acpi_pad hfi1(OE) rdmavt(OE) rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_core binfmt_misc numatools(OE) xpmem(OE) ip_tables
   nfsv3 nfs_acl nfs lockd grace sunrpc fscache igb ahci i2c_algo_bit libahci dca ptp libata pps_core crc32c_intel [last unloaded: i2c_algo_bit]
  CPU: 52 PID: 77418 Comm: pvbatch Kdump: loaded Tainted: G           OE  ------------   3.10.0-957.38.3.el7.x86_64 #1
  Hardware name: HPE.COM HPE SGI 8600-XA730i Gen10/X11DPT-SB-SG007, BIOS SBED1229 01/22/2019
  Call Trace:
   [<ffffffff90365ac0>] dump_stack+0x19/0x1b
   [<ffffffff8fc98b78>] __warn+0xd8/0x100
   [<ffffffff8fc98bff>] warn_slowpath_fmt+0x5f/0x80
   [<ffffffff8ff970c3>] __list_del_entry+0x63/0xd0
   [<ffffffff8ff9713d>] list_del+0xd/0x30
   [<ffffffff8fddda70>] kmem_cache_destroy+0x50/0x110
   [<ffffffffc0328130>] hfi1_user_sdma_free_queues+0xf0/0x200 [hfi1]
   [<ffffffffc02e2350>] hfi1_file_close+0x70/0x1e0 [hfi1]
   [<ffffffff8fe4519c>] __fput+0xec/0x260
   [<ffffffff8fe453fe>] ____fput+0xe/0x10
   [<ffffffff8fcbfd1b>] task_work_run+0xbb/0xe0
   [<ffffffff8fc2bc65>] do_notify_resume+0xa5/0xc0
   [<ffffffff90379134>] int_signal+0x12/0x17
  BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
  IP: [<ffffffff8fe1f93e>] kmem_cache_close+0x7e/0x300
  PGD 2cdab19067 PUD 2f7bfdb067 PMD 0
  Oops: 0000 [#1] SMP
  Modules linked in: mmfs26(OE) mmfslinux(OE) tracedev(OE) 8021q garp mrp ib_isert iscsi_target_mod target_core_mod crc_t10dif crct10dif_generic opa_vnic rpcrdma ib_iser libiscsi scsi_transport_iscsi ib_ipoib(OE) bridge stp llc iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crct10dif_pclmul crct10dif_common crc32_pclmul ghash_clmulni_intel ast aesni_intel ttm lrw gf128mul glue_helper ablk_helper drm_kms_helper cryptd syscopyarea sysfillrect sysimgblt fb_sys_fops drm pcspkr joydev lpc_ich mei_me drm_panel_orientation_quirks i2c_i801 mei wmi ipmi_si ipmi_devintf ipmi_msghandler nfit libnvdimm acpi_power_meter acpi_pad hfi1(OE) rdmavt(OE) rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_core binfmt_misc numatools(OE) xpmem(OE) ip_tables
   nfsv3 nfs_acl nfs lockd grace sunrpc fscache igb ahci i2c_algo_bit libahci dca ptp libata pps_core crc32c_intel [last unloaded: i2c_algo_bit]
  CPU: 52 PID: 77418 Comm: pvbatch Kdump: loaded Tainted: G        W  OE  ------------   3.10.0-957.38.3.el7.x86_64 #1
  Hardware name: HPE.COM HPE SGI 8600-XA730i Gen10/X11DPT-SB-SG007, BIOS SBED1229 01/22/2019
  task: ffff88cc26db9040 ti: ffff88b5393a8000 task.ti: ffff88b5393a8000
  RIP: 0010:[<ffffffff8fe1f93e>]  [<ffffffff8fe1f93e>] kmem_cache_close+0x7e/0x300
  RSP: 0018:ffff88b5393abd60  EFLAGS: 00010287
  RAX: 0000000000000000 RBX: ffff88cb2c6ac000 RCX: 0000000000000003
  RDX: 0000000000000400 RSI: 0000000000000400 RDI: ffffffff9095b800
  RBP: ffff88b5393abdb0 R08: ffffffff9095b808 R09: ffffffff8ff77c19
  R10: ffff88b73ce1f160 R11: ffffddecddde9800 R12: ffff88cb2c6ac000
  R13: 000000000000000c R14: ffff88cf3fdca780 R15: 0000000000000000
  FS:  00002aaaaab52500(0000) GS:ffff88b73ce00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000010 CR3: 0000002d27664000 CR4: 00000000007607e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  PKRU: 55555554
  Call Trace:
   [<ffffffff8fe20d44>] __kmem_cache_shutdown+0x14/0x80
   [<ffffffff8fddda78>] kmem_cache_destroy+0x58/0x110
   [<ffffffffc0328130>] hfi1_user_sdma_free_queues+0xf0/0x200 [hfi1]
   [<ffffffffc02e2350>] hfi1_file_close+0x70/0x1e0 [hfi1]
   [<ffffffff8fe4519c>] __fput+0xec/0x260
   [<ffffffff8fe453fe>] ____fput+0xe/0x10
   [<ffffffff8fcbfd1b>] task_work_run+0xbb/0xe0
   [<ffffffff8fc2bc65>] do_notify_resume+0xa5/0xc0
   [<ffffffff90379134>] int_signal+0x12/0x17
  Code: 00 00 ba 00 04 00 00 0f 4f c2 3d 00 04 00 00 89 45 bc 0f 84 e7 01 00 00 48 63 45 bc 49 8d 04 c4 48 89 45 b0 48 8b 80 c8 00 00 00 <48> 8b 78 10 48 89 45 c0 48 83 c0 10 48 89 45 d0 48 8b 17 48 39
  RIP  [<ffffffff8fe1f93e>] kmem_cache_close+0x7e/0x300
   RSP <ffff88b5393abd60>
  CR2: 0000000000000010

The panic is the result of slab entries being freed during the destruction
of the pq slab.

The code attempts to quiesce the pq, but looking for n_req == 0 doesn't
account for new requests.

Fix the issue by using SRCU to get a pq pointer and adjust the pq free
logic to NULL the fd pq pointer prior to the quiesce.

Fixes: e87473bc ("IB/hfi1: Only set fd pointer when base context is completely initialized")
Link: https://lore.kernel.org/r/20200210131033.87408.81174.stgit@awfm-01.aw.intel.comReviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Each user context is allocated a certain number of RcvArray (TID)
entries and these entries are managed through TID groups. These groups
are put into one of three lists in each user context: tid_group_list,
tid_used_list, and tid_full_list, depending on the number of used TID
entries within each group. When TID packets are expected, one or more
TID groups will be allocated. After the packets are received, the TID
groups will be freed. Since multiple user threads may access the TID
groups simultaneously, a mutex exp_mutex is used to synchronize the
access. However, when the user file is closed, it tries to release
all TID groups without acquiring the mutex first, which risks a race
condition with another thread that may be releasing its TID groups,
leading to data corruption.

This patch addresses the issue by acquiring the mutex first before
releasing the TID groups when the file is closed.

Fixes: 3abb33ac ("staging/hfi1: Add TID cache receive init and free funcs")
Link: https://lore.kernel.org/r/20200210131026.87408.86853.stgit@awfm-01.aw.intel.comReviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Make sure to free the allocated cpumask_var_t's to avoid the following
reported memory leak by kmemleak:

$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff8897f812d6a8 (size 8):
  comm "kworker/1:1", pid 347, jiffies 4294751400 (age 101.703s)
  hex dump (first 8 bytes):
    00 00 00 00 00 00 00 00                          ........
  backtrace:
    [<00000000bff49664>] alloc_cpumask_var_node+0x4c/0xb0
    [<0000000075d3ca81>] hfi1_comp_vectors_set_up+0x20f/0x800 [hfi1]
    [<0000000098d420df>] hfi1_init_dd+0x3311/0x4960 [hfi1]
    [<0000000071be7e52>] init_one+0x25e/0xf10 [hfi1]
    [<000000005483d4c2>] local_pci_probe+0xd4/0x180
    [<000000007c3cbc6e>] work_for_cpu_fn+0x51/0xa0
    [<000000001d626905>] process_one_work+0x8f0/0x17b0
    [<000000007e569e7e>] worker_thread+0x536/0xb50
    [<00000000fd39a4a5>] kthread+0x30c/0x3d0
    [<0000000056f2edb3>] ret_from_fork+0x3a/0x50

Fixes: 5d18ee67 ("IB/{hfi1, rdmavt, qib}: Implement CQ completion vector support")
Link: https://lore.kernel.org/r/20200205110530.12129-1-kamalheib1@gmail.comSigned-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.

This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
  ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
  arm64: defconfig: Enable Broadcom's GENET Ethernet controller
  ARM: multi_v7_defconfig: Enable devfreq thermal integration
  ARM: exynos_defconfig: Enable devfreq thermal integration
  ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
  ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
  arm64: defconfig: Enable Actions Semi specific drivers
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
  ARM: configs: at91: enable config flags for sam9x60 SoC
  ARM: configs: at91: use savedefconfig
  arm64: defconfig: Enable tegra XUDC support
  ARM: defconfig: gemini: Update defconfig
  arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
  arm64: defconfig: enable CONFIG_QCOM_CPR
  arm64: defconfig: Enable HFPLL
  arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
  ARM: imx_v6_v7_defconfig: Select the TFP410 driver
  ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
  arm64: defconfig: Enable ATH10K_SNOC
  ...

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - Nvidia: Fuse support for Tegra194, continued memory controller
     pieces for Tegra30

   - NXP/FSL: Refactorings of QuickEngine drivers to support
     ARM/ARM64/PPC

   - NXP/FSL: i.MX8MP SoC driver pieces

   - TI Keystone: ring accelerator driver

   - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.

   - Xilinx ZynqMP: feature checking interface for firmware. Mailbox
     communication for power management

   - Overall support patch set for cpuidle on more complex hierarchies
     (PSCI-based)

  and misc cleanups, refactorings of Marvell, TI, other platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
  drivers: soc: xilinx: Use mailbox IPI callback
  dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
  drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
  MAINTAINERS: Add brcmstb PCIe controller entry
  soc/tegra: fuse: Unmap registers once they are not needed anymore
  soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
  soc/tegra: fuse: Warn if straps are not ready
  soc/tegra: fuse: Cache values of straps and Chip ID registers
  memory: tegra30-emc: Correct error message for timed out auto calibration
  memory: tegra30-emc: Firm up hardware programming sequence
  memory: tegra30-emc: Firm up suspend/resume sequence
  soc/tegra: regulators: Do nothing if voltage is unchanged
  memory: tegra: Correct reset value of xusb_hostr
  soc/tegra: fuse: Add APB DMA dependency for Tegra20
  bus: tegra-aconnect: Remove PM_CLK dependency
  dt-bindings: mediatek: add MT6765 power dt-bindings
  soc: mediatek: cmdq: delete not used define
  memory: tegra: Add support for the Tegra194 memory controller
  memory: tegra: Only include support for enabled SoCs
  memory: tegra: Support DVFS on Tegra186 and later
  ...

Pull ARM Device-tree updates from Olof Johansson:
 "New SoCs:

   - Atmel/Microchip SAM9X60 (ARM926 SoC)

   - OMAP 37xx gets split into AM3703/AM3715/DM3725, who are all
     variants of it with different GPU/media IP configurations.

   - ST stm32mp15 SoCs (1-2 Cortex-A7, CAN, GPU depending on SKU)

   - ST Ericsson ab8505 (variant of ab8500) and db8520 (variant of
     db8500)

   - Unisoc SC9863A SoC (8x Cortex-A55 mobile chipset w/ GPU, modem)

   - Qualcomm SC7180 (8-core 64bit SoC, unnamed CPU class)

  New boards:

   - Allwinner:
      + Emlid Neutis SoM (H3 variant)
      + Libre Computer ALL-H3-IT
      + PineH64 Model B

   - Amlogic:
      + Libretech Amlogic GX PC (s905d and s912-based variants)

   - Atmel/Microchip:
      + Kizboxmini, sam9x60 EK, sama5d27 Wireless SOM (wlsom1)

   - Marvell:
      + Armada 385-based SolidRun Clearfog GTR

   - NXP:
      + Gateworks GW59xx boards based on i.MX6/6Q/6QDL
      + Tolino Shine 3 eBook reader (i.MX6sl)
      + Embedded Artists COM (i.MX7ULP)
      + SolidRun CLearfog CX/ITX and HoneyComb (LX2160A-based systems)
      + Google Coral Edge TPU (i.MX8MQ)

   - Rockchip:
      + Radxa Dalang Carrier (supports rk3288 and rk3399 SOMs)
      + Radxa Rock Pi N10 (RK3399Pro-based)
      + VMARC RK3399Pro SOM

   - ST:
      + Reference boards for stm32mp15

   - ST Ericsson:
      + Samsung Galaxy S III mini (GT-I8190)
      + HREF520 reference board for DB8520

   - TI OMAP:
      + Gen1 Amazon Echo (OMAP3630-based)

   - Qualcomm:
      + Inforce 6640 Single Board Computer (msm8996-based)
      + SC7180 IDP (SC7180-based)"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (623 commits)
  dt-bindings: fix compilation error of the example in marvell,mmp3-hsic-phy.yaml
  arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
  arm64: dts: ti: k3-am65-main Add CAL node
  arm64: dts: ti: k3-j721e-main: Add McASP nodes
  arm64: dts: ti: k3-am654-main: Add McASP nodes
  arm64: dts: ti: k3-j721e: DMA support
  arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
  arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
  arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
  arm64: dts: ti: k3-am65: DMA support
  arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
  arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
  ARM: dts: aspeed: rainier: Add UCD90320 power sequencer
  ARM: dts: aspeed: rainier: Switch PSUs to unknown version
  arm64: dts: rockchip: Kill off "simple-panel" compatibles
  ARM: dts: rockchip: Kill off "simple-panel" compatibles
  arm64: dts: rockchip: rename dwmmc node names to mmc
  ARM: dts: rockchip: rename dwmmc node names to mmc
  arm64: dts: exynos: Rename Samsung and Exynos to lowercase
  arm64: dts: uniphier: add reset-names to NAND controller node
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Most of these are smaller fixes that have accrued, and some continued
  cleanup of OMAP platforms towards shared frameworks.

  One new SoC from Atmel/Microchip: sam9x60"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
  ARM: OMAP2+: Fix undefined reference to omap_secure_init
  ARM: s3c64xx: Drop unneeded select of TIMER_OF
  ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
  ARM: s3c24xx: Switch to atomic pwm API in rx1950
  ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
  ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
  ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
  ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
  ARM: at91: Documentation: add sam9x60 product and datasheet
  ARM: at91: pm: use of_device_id array to find the proper shdwc node
  ARM: at91: pm: use SAM9X60 PMC's compatible
  ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
  ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
  ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
  ARM: tegra: Modify reshift divider during LP1
  ARM: tegra: Enable PLLP bypass during Tegra124 LP1
  ARM: samsung: Rename Samsung and Exynos to lowercase
  ARM: exynos: Correct the help text for platform Kconfig option
  ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
  ARM: brcmstb: Add debug UART entry for 7216
  ...

Pull compat-ioctl fix from Arnd Bergmann:
 "One patch in the compat-ioctl series broke 32-bit rootfs for multiple
  people testing on 64-bit kernels. Let's fix it in -rc1 before others
  run into the same issue"

* tag 'compat-ioctl-fix' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground:
  compat_ioctl: fix FIONREAD on devices

Pull vfs file system parameter updates from Al Viro:
 "Saner fs_parser.c guts and data structures. The system-wide registry
  of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
  the horror switch() in fs_parse() that would have to grow another case
  every time something got added to that system-wide registry.

  New syntax types can be added by filesystems easily now, and their
  namespace is that of functions - not of system-wide enum members. IOW,
  they can be shared or kept private and if some turn out to be widely
  useful, we can make them common library helpers, etc., without having
  to do anything whatsoever to fs_parse() itself.

  And we already get that kind of requests - the thing that finally
  pushed me into doing that was "oh, and let's add one for timeouts -
  things like 15s or 2h". If some filesystem really wants that, let them
  do it. Without somebody having to play gatekeeper for the variants
  blessed by direct support in fs_parse(), TYVM.

  Quite a bit of boilerplate is gone. And IMO the data structures make a
  lot more sense now. -200LoC, while we are at it"

* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
  tmpfs: switch to use of invalfc()
  cgroup1: switch to use of errorfc() et.al.
  procfs: switch to use of invalfc()
  hugetlbfs: switch to use of invalfc()
  cramfs: switch to use of errofc() et.al.
  gfs2: switch to use of errorfc() et.al.
  fuse: switch to use errorfc() et.al.
  ceph: use errorfc() and friends instead of spelling the prefix out
  prefix-handling analogues of errorf() and friends
  turn fs_param_is_... into functions
  fs_parse: handle optional arguments sanely
  fs_parse: fold fs_parameter_desc/fs_parameter_spec
  fs_parser: remove fs_parameter_description name field
  add prefix to fs_context->log
  ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
  new primitive: __fs_parse()
  switch rbd and libceph to p_log-based primitives
  struct p_log, variants of warnf() et.al. taking that one instead
  teach logfc() to handle prefices, give it saner calling conventions
  get rid of cg_invalf()
  ...

Pull misc vfs updates from Al Viro:

 - bmap series from cmaiolino

 - getting rid of convolutions in copy_mount_options() (use a couple of
   copy_from_user() instead of the __get_user() crap)

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  saner copy_mount_options()
  fibmap: Reject negative block numbers
  fibmap: Use bmap instead of ->bmap method in ioctl_fibmap
  ecryptfs: drop direct calls to ->bmap
  cachefiles: drop direct usage of ->bmap method.
  fs: Enable bmap() function to properly return errors

Merge thundering herd avoidance on pipe IO.

This would have been applied for 5.5 already, but got delayed because of
a user-space race condition in the GNU make jobserver code.  Now that
there's a new GNU make 4.3 release, and most distributions seem to have
at least applied the (almost three year old) fix for the problem, let's
see if people notice.

And it might have been just bad random timing luck on my machine.

If you do hit the race condition, things will still work, but the
symptom is that you don't get nearly the expected parallelism when using
"make -j<N>".

The jobserver bug can definitely happen without this patch too, but
seems to be easier to trigger when we no longer wake up pipe waiters
unnecessarily.

* pipe-exclusive-wakeup:
  pipe: use exclusive waits when reading or writing

This makes the pipe code use separate wait-queues and exclusive waiting
for readers and writers, avoiding a nasty thundering herd problem when
there are lots of readers waiting for data on a pipe (or, less commonly,
lots of writers waiting for a pipe to have space).

While this isn't a common occurrence in the traditional "use a pipe as a
data transport" case, where you typically only have a single reader and
a single writer process, there is one common special case: using a pipe
as a source of "locking tokens" rather than for data communication.

In particular, the GNU make jobserver code ends up using a pipe as a way
to limit parallelism, where each job consumes a token by reading a byte
from the jobserver pipe, and releases the token by writing a byte back
to the pipe.

This pattern is fairly traditional on Unix, and works very well, but
will waste a lot of time waking up a lot of processes when only a single
reader needs to be woken up when a writer releases a new token.

A simplified test-case of just this pipe interaction is to create 64
processes, and then pass a single token around between them (this
test-case also intentionally passes another token that gets ignored to
test the "wake up next" logic too, in case anybody wonders about it):

    #include <unistd.h>

    int main(int argc, char **argv)
    {
        int fd[2], counters[2];

        pipe(fd);
        counters[0] = 0;
        counters[1] = -1;
        write(fd[1], counters, sizeof(counters));

        /* 64 processes */
        fork(); fork(); fork(); fork(); fork(); fork();

        do {
                int i;
                read(fd[0], &i, sizeof(i));
                if (i < 0)
                        continue;
                counters[0] = i+1;
                write(fd[1], counters, (1+(i & 1)) *sizeof(int));
        } while (counters[0] < 1000000);
        return 0;
    }

and in a perfect world, passing that token around should only cause one
context switch per transfer, when the writer of a token causes a
directed wakeup of just a single reader.

But with the "writer wakes all readers" model we traditionally had, on
my test box the above case causes more than an order of magnitude more
scheduling: instead of the expected ~1M context switches, "perf stat"
shows

        231,852.37 msec task-clock                #   15.857 CPUs utilized
        11,250,961      context-switches          #    0.049 M/sec
           616,304      cpu-migrations            #    0.003 M/sec
             1,648      page-faults               #    0.007 K/sec
 1,097,903,998,514      cycles                    #    4.735 GHz
   120,781,778,352      instructions              #    0.11  insn per cycle
    27,997,056,043      branches                  #  120.754 M/sec
       283,581,233      branch-misses             #    1.01% of all branches

      14.621273891 seconds time elapsed

       0.018243000 seconds user
       3.611468000 seconds sys

before this commit.

After this commit, I get

          5,229.55 msec task-clock                #    3.072 CPUs utilized
         1,212,233      context-switches          #    0.232 M/sec
           103,951      cpu-migrations            #    0.020 M/sec
             1,328      page-faults               #    0.254 K/sec
    21,307,456,166      cycles                    #    4.074 GHz
    12,947,819,999      instructions              #    0.61  insn per cycle
     2,881,985,678      branches                  #  551.096 M/sec
        64,267,015      branch-misses             #    2.23% of all branches

       1.702148350 seconds time elapsed

       0.004868000 seconds user
       0.110786000 seconds sys

instead. Much better.

[ Note! This kernel improvement seems to be very good at triggering a
  race condition in the make jobserver (in GNU make 4.2.1) for me. It's
  a long known bug that was fixed back in June 2017 by GNU make commit
  b552b0525198 ("[SV 51159] Use a non-blocking read with pselect to
  avoid hangs.").

  But there wasn't a new release of GNU make until 4.3 on Jan 19 2020,
  so a number of distributions may still have the buggy version. Some
  have backported the fix to their 4.2.1 release, though, and even
  without the fix it's quite timing-dependent whether the bug actually
  is hit. ]

Josh Triplett says:
 "I've been hammering on your pipe fix patch (switching to exclusive
  wait queues) for a month or so, on several different systems, and I've
  run into no issues with it. The patch *substantially* improves
  parallel build times on large (~100 CPU) systems, both with parallel
  make and with other things that use make's pipe-based jobserver.

  All current distributions (including stable and long-term stable
  distributions) have versions of GNU make that no longer have the
  jobserver bug"
Tested-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

My final cleanup patch for sys_compat_ioctl() introduced a regression on
the FIONREAD ioctl command, which is used for both regular and special
files, but only works on regular files after my patch, as I had missed
the warning that Al Viro put into a comment right above it.

Change it back so it can work on any file again by moving the implementation
to do_vfs_ioctl() instead.

Fixes: 77b90401 ("compat_ioctl: simplify the implementation")
Reported-and-tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Reported-and-tested-by: youling257 <youling257@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'irqchip-fixes-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes for 5.6, take #1 from Marc Zyngier:

 - Guarantee allocation of L2 vPE table for GICv4.1
 - Fix GICv4.1 VPROPBASER programming
 - Numerous GICv4.1 tidy ups
 - Fix disabled GICv3 redistributor provisioning with ACPI
 - KConfig cleanup for C-SKY

The configuration of the OCTEONTX XCV_DLL_CTL register via
xcv_init_hw() is such that the RGMII RX delay is bypassed
leaving the RGMII TX delay enabled in the MAC:

	/* Configure DLL - enable or bypass
	 * TX no bypass, RX bypass
	 */
	cfg = readq_relaxed(xcv->reg_base + XCV_DLL_CTL);
	cfg &= ~0xFF03;
	cfg |= CLKRX_BYP;
	writeq_relaxed(cfg, xcv->reg_base + XCV_DLL_CTL);

This would coorespond to a interface type of PHY_INTERFACE_MODE_RGMII_RXID
and not PHY_INTERFACE_MODE_RGMII.

Fixing this allows RGMII PHY drivers to do the right thing (enable
RX delay in the PHY) instead of erroneously enabling both delays in the
PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.6

First set of fixes for v5.6. Buffer overflow fixes to mwifiex, quite a
few functionality fixes to iwlwifi and smaller fixes to other drivers.

mwifiex

* fix an unlock from a previous security fix

* fix two buffer overflows

libertas

* fix two bugs from previous security fixes

iwlwifi

* fix module removal with multiple NICs

* don't treat IGTK removal failure as an error

* avoid FW crashes due to DTS measurement races

* fix a potential use after free in FTM code

* prevent a NULL pointer dereference in iwl_mvm_cfg_he_sta()

* fix TDLS discovery

* check all CPUs when trying to detect an error during resume

rtw88

* fix clang warning

mt76

* fix reading of max_nss value from a register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2020-02-07

The following pull-request contains BPF updates for your *net* tree.

We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).

The main changes are:

1) Various BPF sockmap fixes related to RCU handling in the map's tear-
   down code, from Jakub Sitnicki.

2) Fix macro state explosion in BPF sk_storage map when calculating its
   bucket_log on allocation, from Martin KaFai Lau.

3) Fix potential BPF sockmap update race by rechecking socket's established
   state under lock, from Lorenz Bauer.

4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
   sysctl is set, from Toke Høiland-Jørgensen.

5) Fix i40e's XSK wakeup code to return proper error in busy state and
   various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.

6) Fix the way modifiers are skipped in BTF in the verifier while walking
   pointers to avoid program rejection, from Alexei Starovoitov.

7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
   ii) to fix undefined reference linker errors for older gcc version due to
   order of passed gcc parameters, from Yulia Kartseva and Song Liu.

8) Fix a trampoline_count BPF kselftest warning about missing braces around
   initializer, from Andrii Nakryiko.

9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
   bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_PROVE_LOCKING is selected together with (now default)
CONFIG_VMAP_STACK, kernel enter deadlock during boot.

At the point of checking whether interrupts are enabled or not, the
value of MSR saved on stack is read using the physical address of the
stack. But at this point, when using VMAP stack the DATA MMU
translation has already been re-enabled, leading to deadlock.

Don't use the physical address of the stack when
CONFIG_VMAP_STACK is set.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 02847487 ("powerpc/32: prepare for CONFIG_VMAP_STACK")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/daeacdc0dec0416d1c587cc9f9e7191ad3068dc0.1581095957.git.christophe.leroy@c-s.fr

The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.

At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.

However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").

futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:

  1:     lwarx   %1,  0, %3
         cmpw    0,  %1, %4
         bne-    3f
  2:     stwcx.  %5,  0, %3

Which clearly loads and stores from/to %3. The logic in
arch_futex_atomic_op_inuser() is similar, so fix both of them to use
allow_read_write_user().

Without this fix, and with PPC_KUAP_DEBUG=y, we see eg:

  Bug: Read fault blocked by AMR!
  WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30
  CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G        W         5.5.0-rc7-gcc9x-g4c25df56 #1
  ...
  NIP [c000000000070680] __do_page_fault+0x600/0xf30
  LR [c00000000007067c] __do_page_fault+0x5fc/0xf30
  Call Trace:
  [c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable)
  [c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30
  --- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0
      LR = futex_lock_pi_atomic+0xe0/0x1f0
  [c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable)
  [c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60
  [c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0
  [c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200
  [c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68

Fixes: de78a9c4 ("powerpc: Add a framework for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au