Claudiu Beznea says:

====================
net: macb: add support for sama7g5

This series adds support for SAMA7G5 Ethernet interfaces: one 10/100Mbps
and one 1Gbps interfaces.

Along with it I also included a fix to disable clocks for SiFive FU540-C000
on failure path of fu540_c000_clk_init().

Thank you,
Claudiu Beznea

Changed in v3:
- use clk_bulk_disable_unprepare in patch 3/8
- corrected clang compilation warning in patch 3/8
- revert changes in macb_clk_init() in patch 3/8

Changes in v2:
- introduced patch "net: macb: add function to disable all macb clocks" and
  update patch "net: macb: unprepare clocks in case of failure" accordingly
- collected tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SAMA7G5 10/100Mbps interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add documentation for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add documentation for SAMA7G5 ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unprepare clocks in case of any failure in fu540_c000_clk_init().

Fixes: c218ad55 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add function to disable all macb clocks.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

SAMA7G5's ethernet IPs TX clock could be provided by its generic clock or
by the external clock provided by the PHY. The internal IP logic divides
properly this clock depending on the link speed. The patch adds a new
capability so that macb_set_tx_clock() to not be called for IPs having
this capability (the clock rate, in case of generic clock, is set at the
boot time via device tree and the driver only enables it).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is necessary for SAMA7G5 as it uses different values for
PHY interface and also introduces hdfctlen bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

- NET_ACT_CONNMARK and NET_ACT_CTINFO only require conntrack support.
- NET_ACT_IPT only requires NETFILTER_XTABLES symbols, not
  IP_NF_IPTABLES. After this patch, NET_ACT_IPT becomes consistent
  with NET_EMATCH_IPT. NET_ACT_IPT dependency on IP_NF_IPTABLES predates
  Linux-2.6.12-rc2 (initial git repository build).

Fixes: 22a5dc0e ("net: sched: Introduce connmark action")
Fixes: 24ec483c ("net: sched: Introduce act_ctinfo action")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20201208204707.11268-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Shay Agroskin says:

====================
XDP Redirect implementation for ENA driver

ENA is adding XDP Redirect support for its driver and some other
small tweaks.

This series adds the following:

- Make log messages in the driver have a uniform format using
  netdev_* function
- Improve code readability
- Add support for XDP Redirect
====================

Link: https://lore.kernel.org/r/20201208180208.26111-1-shayagr@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch implements the ndo_xdp_xmit() net_device function which is
called when a packet is redirected to this driver using an
XDP_REDIRECT directive.

The function receives an array of xdp frames that it needs to xmit.
The TX queues that are used to xmit these frames are the XDP
queues used by the XDP_TX flow. Therefore a lock is added to synchronize
both flows (XDP_TX and XDP_REDIRECT).
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

XDP subsystem has a function to free XDP frames and their associated
pages. Using this function would help the driver's XDP implementation to
adjust to new changes in the XDP subsystem in the kernel (e.g.
introduction of XDP MB).

Also, remove 'xdp_rx_page' field from ena_tx_buffer struct since it is
no longer used.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds a partial support for the XDP_REDIRECT directive which
instructs the driver to pass the packet to an interface specified by the
program. The directive is passed to the driver by calling bpf_redirect()
or bpf_redirect_map() functions from the eBPF program.

To lay the ground for integration with the existing XDP TX
implementation the patch removes the redundant page ref count increase
in ena_xdp_xmit_frame() and then decrease in ena_clean_rx_irq(). Instead
it only DMA unmaps descriptors for which XDP TX or REDIRECT directive
was received.

The XDP Redirect support is still missing .ndo_xdp_xmit function
implementation, which allows to redirect packet to an ENA interface,
which would be added in a later patch.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rename the ena_xdp_xmit_buff() function to ena_xdp_xmit_frame() and pass
it an xdp_frame struct instead of xdp_buff.
This change lays the ground for XDP redirect implementation which uses
xdp_frames when 'xmit'ing packets.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce ena_increase_stat() function to increase statistics by a
certain number.
The function includes the
    - lock aquire (on 32bit machines)
    - stat increase
    - lock release (on 32bit machines)

line sequence that is ubiquitous across the driver.

The function increases a single stat at a time and several stats which
are increased together weren't put into a function to avoid
calling the function several times for each stat which looks bad and
might decrease performance.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This commit fixes two nits, but it does not generate any change to binary
because of the optimization of gcc.

  - use `count` instead of `channels->combined_count`
  - change return type from `int` to `bool`

Also add spaces and change macro order in OR assignment to make the code
easier to read.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch changes some of the variables types to match the values they
hold. These wrong types fail some of our static checkers that search for
accidental conversions in our driver.
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ENA logs are adjusted to display the full ENA representation to
distinct each ENA device in case of multiple interfaces.
Using netdev_err/warn and dev_info functions for logging provides
uniform printing with clear distinction of the device and interface.

This patch changes all printing in ena_com files to use netev_* logging
functions except for messages of info level. Log functions of that level
would be printed with dev_info because of the early stage they are
called in when net_device struct isn't yet registered.

To allow using netdev_* functions in all ena_com functions, a pointer to
the net_device was added to ena_com_dev struct.

The patch also adds some log messages to make driver debugging easier.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The patch changes the maximum number of RX/TX queues it advertises to
the kernel (via alloc_etherdev_mq()) from a value received from the
device to a constant value which is the minimum between 128 and the
number of CPUs in the system.

By allocating the net_device struct with a constant number of queues,
the driver is able to allocate it at a much earlier stage, before
calling any ena_com functions. This would allow to make all log prints
in ena_com to use netdev_* log functions instead or current pr_* ones.

Note:
netdev_* prints in ena_com functions that are called before
net_device registration in ena_probe() might print messages that are
a bit ugly (with strings like "(unnamed net_device) (uninitialized)").
However we decided to use netdev_* prints in these functions anyway,
for the sake of getting better messages later, when ena_com functions
are called after ena_probe() form other parts of the driver.
See discussion about this decision in [1].

[1] http://www.mail-archive.com/netdev@vger.kernel.org/msg353590.htmlSigned-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add deprecated flag to indicate < v4.8.7.
Fix idtcm_enable_tod() call correct settime().
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1607442117-13661-4-git-send-email-min.li.xe@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix non-zero phase_adj is lost after snap. Use ktime_sub
to do ktime_t subtraction.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1607442117-13661-3-git-send-email-min.li.xe@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove write phase mode 5 second setup delay, not needed.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1607442117-13661-2-git-send-email-min.li.xe@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

SM_RESET device only when loading full configuration and check
for BOOT_STATUS. Also remove polling for write trigger done in
_idtcm_settime().

Changes since v1:
-Correct warnings from strict checkpatch
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1607442117-13661-1-git-send-email-min.li.xe@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The vrf_add_mac_header_if_unset() is defined within a conditional
compilation block which depends on the CONFIG_IPV6 macro.
However, the vrf_add_mac_header_if_unset() needs to be called also by IPv4
related code and when the CONFIG_IPV6 is not set, this function is missing.
As a consequence, the build process stops reporting the error:

 ERROR: implicit declaration of function 'vrf_add_mac_header_if_unset'

The problem is solved by *only* moving functions
vrf_add_mac_header_if_unset() and vrf_prepare_mac_header() out of the
conditional block.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04893908 ("vrf: add mac header for tunneled packets when sniffer is attached")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201208175210.8906-1-andrea.mayer@uniroma2.itSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MT7530 has a global address age control register, so use it to set
ageing time.

The applied timer is (AGE_CNT + 1) * (AGE_UNIT + 1) seconds
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Awogbemil says:

====================
GVE Raw Addressing
Patchset description:
This  patchset introduces "raw addressing" mode to the GVE driver.
Previously (in "queue_page_list" or "qpl" mode), the driver would
pre-allocate and dma_map buffers to be used on egress and ingress.
On egress, it would copy data from the skb provided to the
pre-allocated buffers - this was expensive.
In raw addressing mode, the driver can avoid this copy and simply
dma_map the skb's data so that the NIC can use it.
On ingress, the driver passes buffers up to the networking stack and
then frees and reallocates buffers when necessary instead of using
skb_copy_to_linear_data.
Patch 3 separates the page refcount tracking mechanism
into a function gve_rx_can_recycle_buffer which uses get_page - this will
be changed in a future patch to eliminate the use of get_page in tracking
page refcounts.

Changes from v9:
  Patch 4: Use u64, not u32 for new tx stat counters.
====================
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During TX, skbs' data addresses are dma_map'ed and passed to the NIC.
This means that the device can perform DMA directly from these addresses
and the driver does not have to copy the buffer content into
pre-allocated buffers/qpls (as in qpl mode).
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch lets the driver reuse buffers that have been freed by the
networking stack.

In the raw addressing case, this allows the driver avoid allocating new
buffers.
In the qpl case, the driver can avoid copies.

This patch separates the page refcount tracking mechanism
into a function gve_rx_can_recycle_buffer which uses get_page - this will
be changed in a future patch to entirely eliminate the use of get_page in
tracking page refcounts.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to use raw dma addresses in the rx path. Due to this new
support we can alloc a new buffer instead of making a copy.

RX buffers are handed to the networking stack and are
re-allocated as needed, avoiding the need to use
skb_copy_to_linear_data() as in "qpl" mode.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to describe device for parsing device options. As
the first device option, add raw addressing.

"Raw Addressing" mode (as opposed to the current "qpl" mode) is an
operational mode which allows the driver avoid bounce buffer copies
which it currently performs using pre-allocated qpls (queue_page_lists)
when sending and receiving packets.
For egress packets, the provided skb data addresses will be dma_map'ed and
passed to the device, allowing the NIC can perform DMA directly - the
driver will not have to copy the buffer content into pre-allocated
buffers/qpls (as in qpl mode).
For ingress packets, copies are also eliminated as buffers are handed to
the networking stack and then recycled or re-allocated as
necessary, avoiding the use of skb_copy_to_linear_data().

This patch only introduces the option to the driver.
Subsequent patches will add the ingress and egress functionality.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2020-12-07

Here's the main bluetooth-next pull request for the 5.11 kernel.

 - Updated Bluetooth entries in MAINTAINERS to include Luiz von Dentz
 - Added support for Realtek 8822CE and 8852A devices
 - Added support for MediaTek MT7615E device
 - Improved workarounds for fake CSR devices
 - Fix Bluetooth qualification test case L2CAP/COS/CFD/BV-14-C
 - Fixes for LL Privacy support
 - Enforce 16 byte encryption key size for FIPS security level
 - Added new mgmt commands for extended advertising support
 - Multiple other smaller fixes & improvements

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>