[ Upstream commit cd224553 ]

xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.

Fix those cases.

Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2dd ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit acf138f1 ]

The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.

The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.

I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.

In commit 123c1407 ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.

Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.

Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407 ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b8c60012 upstream.

Commit 4fcd1813 ("Fix reconnect to not defer smb3 session reconnect
long after socket reconnect") changes the behaviour of the SMB2 echo
service and causes it to renegotiate after a socket reconnect. However
under default settings, the echo service could take up to 120 seconds to
be scheduled.

The patch forces the echo service to be called immediately resulting a
negotiate call being made immediately on reconnect.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit baabd567 upstream.

The driver attempts to alter memory that is mapped to PCI device.

This is because tx_fwinfo_8190pci points to skb->data

Move the pci_map_single to when completed buffer is ready to be mapped with
psdec is empty to drop on mapping error.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 46350b71 upstream.

Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf

states the following:

"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."

So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cc: Stephane Fillod <f8cfe@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 22322035 upstream.

The code in block/partitions/msdos.c recognizes FreeBSD, OpenBSD
and NetBSD partitions and does a reasonable job picking out OpenBSD
and NetBSD UFS subpartitions.

But for FreeBSD the subpartitions are always "bad".

    Kernel: <bsd:bad subpartition - ignored

Though all 3 of these BSD systems use UFS as a file system, only
FreeBSD uses relative start addresses in the subpartition
declarations.

The following patch fixes this for FreeBSD partitions and leaves
the code for OpenBSD and NetBSD intact:
Signed-off-by: Richard Narron <comet.berkeley@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c34a6905 upstream.

The identity mapping is suboptimal for the last 2GB frame. The mapping
will be established with a mix of 4KB and 1MB mappings instead of a
single 2GB mapping.

This happens because of a off-by-one bug introduced with
commit 50be6345 ("s390/mm: Convert bootmem to memblock").

Currently the identity mapping looks like this:

0x0000000080000000-0x0000000180000000        4G PUD RW
0x0000000180000000-0x00000001fff00000     2047M PMD RW
0x00000001fff00000-0x0000000200000000        1M PTE RW

With the bug fixed it looks like this:

0x0000000080000000-0x0000000200000000        6G PUD RW

Fixes: 50be6345 ("s390/mm: Convert bootmem to memblock")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 994870be upstream.

When an inline assembly operand's type is narrower than the register it
is allocated to, the least significant bits of the register (up to the
operand type's width) are valid, and any other bits are permitted to
contain any arbitrary value. This aligns with the AAPCS64 parameter
passing rules.

Our __smp_store_release() implementation does not account for this, and
implicitly assumes that operands have been zero-extended to the width of
the type being stored to. Thus, we may store unknown values to memory
when the value type is narrower than the pointer type (e.g. when storing
a char to a long).

This patch fixes the issue by casting the value operand to the same
width as the pointer operand in all cases, which ensures that the value
is zero-extended as we expect. We use the same union trickery as
__smp_load_acquire and {READ,WRITE}_ONCE() to avoid GCC complaining that
pointers are potentially cast to narrower width integers in unreachable
paths.

A whitespace issue at the top of __smp_store_release() is also
corrected.

No changes are necessary for __smp_load_acquire(). Load instructions
implicitly clear any upper bits of the register, and the compiler will
only consider the least significant bits of the register as valid
regardless.

Fixes: 47933ad4 ("arch: Introduce smp_load_acquire(), smp_store_release()")
Fixes: 878a84d5 ("arm64: add missing data types in smp_load_acquire/smp_store_release")
Cc: <stable@vger.kernel.org> # 3.14.x-
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 55de49f9 upstream.

Our compat swp emulation holds the compat user address in an unsigned
int, which it passes to __user_swpX_asm(). When a 32-bit value is passed
in a register, the upper 32 bits of the register are unknown, and we
must extend the value to 64 bits before we can use it as a base address.

This patch casts the address to unsigned long to ensure it has been
suitably extended, avoiding the potential issue, and silencing a related
warning from clang.

Fixes: bd35a4ad ("arm64: Port SWP/SWPB emulation support from arm")
Cc: <stable@vger.kernel.org> # 3.19.x-
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5f893c5 upstream.

Under SMAP/PAN/etc, we cannot write directly to userspace memory, so
this rearranges the test bytes to get written through copy_to_user().
Additionally drops the bad copy_from_user() test that would trigger a
memcpy() against userspace on failure.

[arnd: the test module was added in 3.14, and this backported patch
       should apply cleanly on all version from 3.14 to 4.10.
       The original patch was in 4.11 on top of a context change
       I saw the bug triggered with kselftest on a 4.4.y stable kernel]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1feb4006 upstream.

The handling of IB_RDMA_WRITE_ONLY_WITH_IMMEDIATE will leak a memory
reference when a buffer cannot be allocated for returning the immediate
data.

The issue is that the rkey validation has already occurred and the RNR
nak fails to release the reference that was fruitlessly gotten.  The
the peer will send the identical single packet request when its RNR
timer pops.

The fix is to release the held reference prior to the rnr nak exit.
This is the only sequence the requires both rkey validation and the
buffer allocation on the same packet.

Cc: Stable <stable@vger.kernel.org> # 4.7+
Tested-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 276e9327 upstream.

This backport has a minor difference from the upstream commit: it adds
the asm-uaccess.h file, which is not present in 4.4, because 4.4 does
not have commit b4b8664d ("arm64: don't pull uaccess.h into *.S").

Original patch description:

When handling a data abort from EL0, we currently zero the top byte of
the faulting address, as we assume the address is a TTBR0 address, which
may contain a non-zero address tag. However, the address may be a TTBR1
address, in which case we should not zero the top byte. This patch fixes
that. The effect is that the full TTBR1 address is passed to the task's
signal handler (or printed out in the kernel log).

When handling a data abort from EL1, we leave the faulting address
intact, as we assume it's either a TTBR1 address or a TTBR0 address with
tag 0x00. This is true as far as I'm aware, we don't seem to access a
tagged TTBR0 address anywhere in the kernel. Regardless, it's easy to
forget about address tags, and code added in the future may not always
remember to remove tags from addresses before accessing them. So add tag
handling to the EL1 data abort handler as well. This also makes it
consistent with the EL0 data abort handler.

Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0")
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7dcd9dd8 upstream.

This backport has a few small differences from the upstream commit:
 - The address tag is removed in watchpoint_handler() instead of
   get_distance_from_watchpoint(), because 4.4 does not have commit
   fdfeff0f ("arm64: hw_breakpoint: Handle inexact watchpoint
   addresses").
 - A macro is backported (untagged_addr), as it is not present in 4.4.

Original patch description:

When we take a watchpoint exception, the address that triggered the
watchpoint is found in FAR_EL1. We compare it to the address of each
configured watchpoint to see which one was hit.

The configured watchpoint addresses are untagged, while the address in
FAR_EL1 will have an address tag if the data access was done using a
tagged address. The tag needs to be removed to compare the address to
the watchpoints.

Currently we don't remove it, and as a result can report the wrong
watchpoint as being hit (specifically, always either the highest TTBR0
watchpoint or lowest TTBR1 watchpoint). This patch removes the tag.

Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 791cc43b upstream.

Commit 2a6fba6d "xfs: only return -errno or success from attr ->put_listent"
changes the returnvalue of __xfs_xattr_put_listen to 0 in case when there is
insufficient space in the buffer assuming that setting context->count to -1
would be enough, but all of the ->put_listent callers only check seen_enough.
This results in a failed assertion:
XFS: Assertion failed: context->count >= 0, file: fs/xfs/xfs_xattr.c, line: 175
in insufficient buffer size case.

This is only reproducible with at least 2 xattrs and only when the buffer
gets depleted before the last one.

Furthermore if buffersize is such that it is enough to hold the last xattr's
name, but not enough to hold the sum of preceeding xattr names listxattr won't
fail with ERANGE, but will suceed returning last xattr's name without the
first character. The first character end's up overwriting data stored at
(context->alist - 1).
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Cc: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 762674f8 upstream.

Donald Buczek reports that a nfs4 client incorrectly denies
execute access based on outdated file mode (missing 'x' bit).
After the mode on the server is 'fixed' (chmod +x) further execution
attempts continue to fail, because the nfs ACCESS call updates
the access parameter but not the mode parameter or the mode in
the inode.

The root cause is ultimately that the VFS is calling may_open()
before the NFS client has a chance to OPEN the file and hence revalidate
the access and attribute caches.

Al Viro suggests:
>>> Make nfs_permission() relax the checks when it sees MAY_OPEN, if you know
>>> that things will be caught by server anyway?
>>
>> That can work as long as we're guaranteed that everything that calls
>> inode_permission() with MAY_OPEN on a regular file will also follow up
>> with a vfs_open() or dentry_open() on success. Is this always the
>> case?
>
> 1) in do_tmpfile(), followed by do_dentry_open() (not reachable by NFS since
> it doesn't have ->tmpfile() instance anyway)
>
> 2) in atomic_open(), after the call of ->atomic_open() has succeeded.
>
> 3) in do_last(), followed on success by vfs_open()
>
> That's all.  All calls of inode_permission() that get MAY_OPEN come from
> may_open(), and there's no other callers of that puppy.
Reported-by: Donald Buczek <buczek@molgen.mpg.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109771
Link: http://lkml.kernel.org/r/1451046656-26319-1-git-send-email-buczek@molgen.mpg.de
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5c5fc09a upstream.

Donald Buczek reports that NFS clients can also report incorrect
results for access() due to lack of revalidation of attributes
before calling execute_ok().
Looking closely, it seems chdir() is afflicted with the same problem.

Fix is to ensure we call nfs_revalidate_inode_rcu() or
nfs_revalidate_inode() as appropriate before deciding to trust
execute_ok().
Reported-by: Donald Buczek <buczek@molgen.mpg.de>
Link: http://lkml.kernel.org/r/1451331530-3748-1-git-send-email-buczek@molgen.mpg.deSigned-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 864b9a39 upstream.

We have seen an early OOM killer invocation on ppc64 systems with
crashkernel=4096M:

	kthreadd invoked oom-killer: gfp_mask=0x16040c0(GFP_KERNEL|__GFP_COMP|__GFP_NOTRACK), nodemask=7, order=0, oom_score_adj=0
	kthreadd cpuset=/ mems_allowed=7
	CPU: 0 PID: 2 Comm: kthreadd Not tainted 4.4.68-1.gd7fe927-default #1
	Call Trace:
	  dump_stack+0xb0/0xf0 (unreliable)
	  dump_header+0xb0/0x258
	  out_of_memory+0x5f0/0x640
	  __alloc_pages_nodemask+0xa8c/0xc80
	  kmem_getpages+0x84/0x1a0
	  fallback_alloc+0x2a4/0x320
	  kmem_cache_alloc_node+0xc0/0x2e0
	  copy_process.isra.25+0x260/0x1b30
	  _do_fork+0x94/0x470
	  kernel_thread+0x48/0x60
	  kthreadd+0x264/0x330
	  ret_from_kernel_thread+0x5c/0xa4

	Mem-Info:
	active_anon:0 inactive_anon:0 isolated_anon:0
	 active_file:0 inactive_file:0 isolated_file:0
	 unevictable:0 dirty:0 writeback:0 unstable:0
	 slab_reclaimable:5 slab_unreclaimable:73
	 mapped:0 shmem:0 pagetables:0 bounce:0
	 free:0 free_pcp:0 free_cma:0
	Node 7 DMA free:0kB min:0kB low:0kB high:0kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB isolated(anon):0kB isolated(file):0kB present:52428800kB managed:110016kB mlocked:0kB dirty:0kB writeback:0kB mapped:0kB shmem:0kB slab_reclaimable:320kB slab_unreclaimable:4672kB kernel_stack:1152kB pagetables:0kB unstable:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? yes
	lowmem_reserve[]: 0 0 0 0
	Node 7 DMA: 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 0kB
	0 total pagecache pages
	0 pages in swap cache
	Swap cache stats: add 0, delete 0, find 0/0
	Free swap  = 0kB
	Total swap = 0kB
	819200 pages RAM
	0 pages HighMem/MovableOnly
	817481 pages reserved
	0 pages cma reserved
	0 pages hwpoisoned

the reason is that the managed memory is too low (only 110MB) while the
rest of the the 50GB is still waiting for the deferred intialization to
be done.  update_defer_init estimates the initial memoty to initialize
to 2GB at least but it doesn't consider any memory allocated in that
range.  In this particular case we've had

	Reserving 4096MB of memory at 128MB for crashkernel (System RAM: 51200MB)

so the low 2GB is mostly depleted.

Fix this by considering memblock allocations in the initial static
initialization estimation.  Move the max_initialise to
reset_deferred_meminit and implement a simple memblock_reserved_memory
helper which iterates all reserved blocks and sums the size of all that
start below the given address.  The cumulative size is than added on top
of the initial estimation.  This is still not ideal because
reset_deferred_meminit doesn't consider holes and so reservation might
be above the initial estimation whihch we ignore but let's make the
logic simpler until we really need to handle more complicated cases.

Fixes: 3a80a7fa ("mm: meminit: initialise a subset of struct pages if CONFIG_DEFERRED_STRUCT_PAGE_INIT is set")
Link: http://lkml.kernel.org/r/20170531104010.GI27783@dhcp22.suse.czSigned-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 52bd2d62 upstream.

skb->sender_cpu and skb->napi_id share a common storage,
and we had various bugs about this.

We had to call skb_sender_cpu_clear() in some places to
not leave a prior skb->napi_id and fool netdev_pick_tx()

As suggested by Alexei, we could split the space so that
these errors can not happen.

0 value being reserved as the common (not initialized) value,
let's reserve [1 .. NR_CPUS] range for valid sender_cpu,
and [NR_CPUS+1 .. ~0U] for valid napi_id.

This will allow proper busy polling support over tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3c910176 upstream.

This patch fixes an issue that kernel panic happens when DMA is enabled
and we press enter key while the kernel booting on the serial console.

* An interrupt may occur after sci_request_irq().
* DMA transfer area is initialized by setup_timer() in sci_request_dma()
  and used in interrupt.

If an interrupt occurred between sci_request_irq() and setup_timer() in
sci_request_dma(), DMA transfer area has not been initialized yet.
So, this patch changes the order of sci_request_irq() and
sci_request_dma().

Fixes: 73a19e4c ("serial: sh-sci: Add DMA support.")
Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com>
[Shimoda changes the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e9036d06 upstream.

When the tty lock is interrupted on attempted re-open, 2 tty krefs
are still held. Drop extra kref before returning failure from
tty_lock_interruptible(), and drop lookup kref before returning
failure from tty_open().

Fixes: 0bfd464d ("tty: Wait interruptibly for tty lock on reopen")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 32829da5 upstream.

A recent fix to /dev/mem prevents mappings from wrapping around the end
of physical address space. However, the check was written in a way that
also prevents a mapping reaching just up to the end of physical address
space, which may be a valid use case (especially on 32-bit systems).
This patch fixes it by checking the last mapped address (instead of the
first address behind that) for overflow.

Fixes: b299cde2 ("drivers: char: mem: Check for address space wraparound with mmap()")
Reported-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4efda5f2 upstream.

soc_cleanup_card_resources() call snd_card_free() at the last of its
procedure.  This turned out to lead to a use-after-free.
PCM runtimes have been already removed via soc_remove_pcm_runtimes(),
while it's dereferenced later in soc_pcm_free() called via
snd_card_free().

The fix is simple: just move the snd_card_free() call to the beginning
of the whole procedure.  This also gives another benefit: it
guarantees that all operations have been shut down before actually
releasing the resources, which was racy until now.
Reported-and-tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ba3021b2 upstream.

snd_timer_user_tselect() reallocates the queue buffer dynamically, but
it forgot to reset its indices.  Since the read may happen
concurrently with ioctl and snd_timer_user_tselect() allocates the
buffer via kmalloc(), this may lead to the leak of uninitialized
kernel-space data, as spotted via KMSAN:

  BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10
  CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  Call Trace:
   __dump_stack lib/dump_stack.c:16
   dump_stack+0x143/0x1b0 lib/dump_stack.c:52
   kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007
   kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086
   copy_to_user ./arch/x86/include/asm/uaccess.h:725
   snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004
   do_loop_readv_writev fs/read_write.c:716
   __do_readv_writev+0x94c/0x1380 fs/read_write.c:864
   do_readv_writev fs/read_write.c:894
   vfs_readv fs/read_write.c:908
   do_readv+0x52a/0x5d0 fs/read_write.c:934
   SYSC_readv+0xb6/0xd0 fs/read_write.c:1021
   SyS_readv+0x87/0xb0 fs/read_write.c:1018

This patch adds the missing reset of queue indices.  Together with the
previous fix for the ioctl/read race, we cover the whole problem.
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d11662f4 upstream.

The read from ALSA timer device, the function snd_timer_user_tread(),
may access to an uninitialized struct snd_timer_user fields when the
read is concurrently performed while the ioctl like
snd_timer_user_tselect() is invoked.  We have already fixed the races
among ioctls via a mutex, but we seem to have forgotten the race
between read vs ioctl.

This patch simply applies (more exactly extends the already applied
range of) tu->ioctl_lock in snd_timer_user_tread() for closing the
race window.
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b4e382ca upstream.

Reusing the list_head for both is a bad idea.  Callback execution is done
with the lock dropped so that alarms can be rescheduled from the callback,
which means that with some unfortunate timing, lists can get corrupted.

The execution list should not require its own locking, the single function
that uses it can only be called from a single context.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 07678eca upstream.

When vmw_gb_surface_define_ioctl() is called with an existing buffer,
we end up returning an uninitialized variable in the backup_handle.

The fix is to first initialize backup_handle to 0 just to be sure, and
second, when a user-provided buffer is found, we will use the
req->buffer_handle as the backup_handle.
Reported-by: Murray McAllister <murray.mcallister@insomniasec.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ee9c4e68 upstream.

The 'req->mip_levels' parameter in vmw_gb_surface_define_ioctl() is
a user-controlled 'uint32_t' value which is used as a loop count limit.
This can lead to a kernel lockup and DoS. Add check for 'req->mip_levels'.

References:
https://bugzilla.redhat.com/show_bug.cgi?id=1437431Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0c62e98 upstream.

If vmalloc() fails then we need to a bit of cleanup before returning.

Fixes: fb1d9738 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cc1582c2 upstream.

When doing sampling, for example:

  perf record -e cycles:u ...

On workloads that do a lot of kernel entry/exits we see kernel
samples, even though :u is specified. This is due to skid existing.

This might be a security issue because it can leak kernel addresses even
though kernel sampling support is disabled.

The patch drops the kernel samples if exclude_kernel is specified.

For example, test on Haswell desktop:

  perf record -e cycles:u <mgen>
  perf report --stdio

Before patch applied:

    99.77%  mgen     mgen              [.] buf_read
     0.20%  mgen     mgen              [.] rand_buf_init
     0.01%  mgen     [kernel.vmlinux]  [k] apic_timer_interrupt
     0.00%  mgen     mgen              [.] last_free_elem
     0.00%  mgen     libc-2.23.so      [.] __random_r
     0.00%  mgen     libc-2.23.so      [.] _int_malloc
     0.00%  mgen     mgen              [.] rand_array_init
     0.00%  mgen     [kernel.vmlinux]  [k] page_fault
     0.00%  mgen     libc-2.23.so      [.] __random
     0.00%  mgen     libc-2.23.so      [.] __strcasestr
     0.00%  mgen     ld-2.23.so        [.] strcmp
     0.00%  mgen     ld-2.23.so        [.] _dl_start
     0.00%  mgen     libc-2.23.so      [.] sched_setaffinity@@GLIBC_2.3.4
     0.00%  mgen     ld-2.23.so        [.] _start

We can see kernel symbols apic_timer_interrupt and page_fault.

After patch applied:

    99.79%  mgen     mgen           [.] buf_read
     0.19%  mgen     mgen           [.] rand_buf_init
     0.00%  mgen     libc-2.23.so   [.] __random_r
     0.00%  mgen     mgen           [.] rand_array_init
     0.00%  mgen     mgen           [.] last_free_elem
     0.00%  mgen     libc-2.23.so   [.] vfprintf
     0.00%  mgen     libc-2.23.so   [.] rand
     0.00%  mgen     libc-2.23.so   [.] __random
     0.00%  mgen     libc-2.23.so   [.] _int_malloc
     0.00%  mgen     libc-2.23.so   [.] _IO_doallocbuf
     0.00%  mgen     ld-2.23.so     [.] do_lookup_x
     0.00%  mgen     ld-2.23.so     [.] open_verify.constprop.7
     0.00%  mgen     ld-2.23.so     [.] _dl_important_hwcaps
     0.00%  mgen     libc-2.23.so   [.] sched_setaffinity@@GLIBC_2.3.4
     0.00%  mgen     ld-2.23.so     [.] _start

There are only userspace symbols.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Cc: kan.liang@intel.com
Cc: mark.rutland@arm.com
Cc: will.deacon@arm.com
Cc: yao.jin@intel.com
Link: http://lkml.kernel.org/r/1495706947-3744-1-git-send-email-yao.jin@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dc421b20 upstream.

When adding or removing memory, the aa_index (affinity value) for the
memblock must also be converted to match the endianness of the rest
of the 'ibm,dynamic-memory' property.  Otherwise, subsequent retrieval
of the attribute will likely lead to non-existent nodes, followed by
using the default node in the code inappropriately.

Fixes: 5f97b2a0 ("powerpc/pseries: Implement memory hotplug add in the kernel")
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ba4a648f upstream.

In commit 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we
switched to the generic implementation of cpu_to_node(), which uses a percpu
variable to hold the NUMA node for each CPU.

Unfortunately we neglected to notice that we use cpu_to_node() in the allocation
of our percpu areas, leading to a chicken and egg problem. In practice what
happens is when we are setting up the percpu areas, cpu_to_node() reports that
all CPUs are on node 0, so we allocate all percpu areas on node 0.

This is visible in the dmesg output, as all pcpu allocs being in group 0:

  pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
  pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
  pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
  pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31
  pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39
  pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47

To fix it we need an early_cpu_to_node() which can run prior to percpu being
setup. We already have the numa_cpu_lookup_table we can use, so just plumb it
in. With the patch dmesg output shows two groups, 0 and 1:

  pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
  pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
  pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
  pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31
  pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39
  pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47

We can also check the data_offset in the paca of various CPUs, with the fix we
see:

  CPU 0:  data_offset = 0x0ffe8b0000
  CPU 24: data_offset = 0x1ffe5b0000

And we can see from dmesg that CPU 24 has an allocation on node 1:

  node   0: [mem 0x0000000000000000-0x0000000fffffffff]
  node   1: [mem 0x0000001000000000-0x0000001fffffffff]

Fixes: 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit daeba295 upstream.

eeh_handle_special_event() is called when an EEH event is detected but
can't be narrowed down to a specific PE.  This function looks through
every PE to find one in an erroneous state, then calls the regular event
handler eeh_handle_normal_event() once it knows which PE has an error.

However, if eeh_handle_normal_event() found that the PE cannot possibly
be recovered, it will free it, rendering the passed PE stale.
This leads to a use after free in eeh_handle_special_event() as it attempts to
clear the "recovering" state on the PE after eeh_handle_normal_event() returns.

Thus, make sure the PE is valid when attempting to clear state in
eeh_handle_special_event().

Fixes: 8a6b1bc7 ("powerpc/eeh: EEH core to handle special event")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ddff7ed4 upstream.

When pci_enable_device() or pci_enable_device_mem() fail in
qla2x00_probe_one() we bail out but do a call to
pci_disable_device(). This causes the dev_WARN_ON() in
pci_disable_device() to trigger, as the device wasn't enabled
previously.

So instead of taking the 'probe_out' error path we can directly return
*iff* one of the pci_enable_device() calls fails.

Additionally rename the 'probe_out' goto label's name to the more
descriptive 'disable_device'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d6dbdd3c upstream.

Under memory pressure, we start ageing pages, which amounts to parsing
the page tables. Since we don't want to allocate any extra level,
we pass NULL for our private allocation cache. Which means that
stage2_get_pud() is allowed to fail. This results in the following
splat:

[ 1520.409577] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 1520.417741] pgd = ffff810f52fef000
[ 1520.421201] [00000008] *pgd=0000010f636c5003, *pud=0000010f56f48003, *pmd=0000000000000000
[ 1520.429546] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 1520.435156] Modules linked in:
[ 1520.438246] CPU: 15 PID: 53550 Comm: qemu-system-aar Tainted: G        W       4.12.0-rc4-00027-g1885c397eaec #7205
[ 1520.448705] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB12A 10/26/2016
[ 1520.463726] task: ffff800ac5fb4e00 task.stack: ffff800ce04e0000
[ 1520.469666] PC is at stage2_get_pmd+0x34/0x110
[ 1520.474119] LR is at kvm_age_hva_handler+0x44/0xf0
[ 1520.478917] pc : [<ffff0000080b137c>] lr : [<ffff0000080b149c>] pstate: 40000145
[ 1520.486325] sp : ffff800ce04e33d0
[ 1520.489644] x29: ffff800ce04e33d0 x28: 0000000ffff40064
[ 1520.494967] x27: 0000ffff27e00000 x26: 0000000000000000
[ 1520.500289] x25: ffff81051ba65008 x24: 0000ffff40065000
[ 1520.505618] x23: 0000ffff40064000 x22: 0000000000000000
[ 1520.510947] x21: ffff810f52b20000 x20: 0000000000000000
[ 1520.516274] x19: 0000000058264000 x18: 0000000000000000
[ 1520.521603] x17: 0000ffffa6fe7438 x16: ffff000008278b70
[ 1520.526940] x15: 000028ccd8000000 x14: 0000000000000008
[ 1520.532264] x13: ffff7e0018298000 x12: 0000000000000002
[ 1520.537582] x11: ffff000009241b93 x10: 0000000000000940
[ 1520.542908] x9 : ffff0000092ef800 x8 : 0000000000000200
[ 1520.548229] x7 : ffff800ce04e36a8 x6 : 0000000000000000
[ 1520.553552] x5 : 0000000000000001 x4 : 0000000000000000
[ 1520.558873] x3 : 0000000000000000 x2 : 0000000000000008
[ 1520.571696] x1 : ffff000008fd5000 x0 : ffff0000080b149c
[ 1520.577039] Process qemu-system-aar (pid: 53550, stack limit = 0xffff800ce04e0000)
[...]
[ 1521.510735] [<ffff0000080b137c>] stage2_get_pmd+0x34/0x110
[ 1521.516221] [<ffff0000080b149c>] kvm_age_hva_handler+0x44/0xf0
[ 1521.522054] [<ffff0000080b0610>] handle_hva_to_gpa+0xb8/0xe8
[ 1521.527716] [<ffff0000080b3434>] kvm_age_hva+0x44/0xf0
[ 1521.532854] [<ffff0000080a58b0>] kvm_mmu_notifier_clear_flush_young+0x70/0xc0
[ 1521.539992] [<ffff000008238378>] __mmu_notifier_clear_flush_young+0x88/0xd0
[ 1521.546958] [<ffff00000821eca0>] page_referenced_one+0xf0/0x188
[ 1521.552881] [<ffff00000821f36c>] rmap_walk_anon+0xec/0x250
[ 1521.558370] [<ffff000008220f78>] rmap_walk+0x78/0xa0
[ 1521.563337] [<ffff000008221104>] page_referenced+0x164/0x180
[ 1521.569002] [<ffff0000081f1af0>] shrink_active_list+0x178/0x3b8
[ 1521.574922] [<ffff0000081f2058>] shrink_node_memcg+0x328/0x600
[ 1521.580758] [<ffff0000081f23f4>] shrink_node+0xc4/0x328
[ 1521.585986] [<ffff0000081f2718>] do_try_to_free_pages+0xc0/0x340
[ 1521.592000] [<ffff0000081f2a64>] try_to_free_pages+0xcc/0x240
[...]

The trivial fix is to handle this NULL pud value early, rather than
dereferencing it blindly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 896533a7 upstream.

If we fail to add the space_info kobject, we'll leak the memory
for the percpu counter.

Fixes: 6ab0a202 (btrfs: publish allocation data in sysfs)
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cc2b702c upstream.

Variables start_idx and end_idx are supposed to hold a page index
derived from the file offsets. The int type is not the right one though,
offsets larger than 1 << 44 will get silently trimmed off the high bits.
(1 << 44 is 16TiB)

What can go wrong, if start is below the boundary and end gets trimmed:
- if there's a page after start, we'll find it (radix_tree_gang_lookup_slot)
- the final check "if (page->index <= end_idx)" will unexpectedly fail

The function will return false, ie. "there's no page in the range",
although there is at least one.

btrfs_page_exists_in_range is used to prevent races in:

* in hole punching, where we make sure there are not pages in the
  truncated range, otherwise we'll wait for them to finish and redo
  truncation, but we're going to replace the pages with holes anyway so
  the only problem is the intermediate state

* lock_extent_direct: we want to make sure there are no pages before we
  lock and start DIO, to prevent stale data reads

For practical occurence of the bug, there are several constaints.  The
file must be quite large, the affected range must cross the 16TiB
boundary and the internal state of the file pages and pending operations
must match.  Also, we must not have started any ordered data in the
range, otherwise we don't even reach the buggy function check.

DIO locking tries hard in several places to avoid deadlocks with
buffered IO and avoids waiting for ranges. The worst consequence seems
to be stale data read.

CC: Liu Bo <bo.li.liu@oracle.com>
Fixes: fc4adbff ("btrfs: Drop EXTENT_UPTODATE check in hole punching and direct locking")
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cec422c1 upstream.

Fix error path if we can't copy user structure on CXL_IOCTL_START_WORK
ioctl. We shouldn't unlock the context status mutex as it was not
locked (yet).

Fixes: 0712dc7e ("cxl: Fix issues when unmapping contexts")
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 006351ac upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 940ef1a0 upstream.

... and it really needs splitting into "new" and "extend" cases, but that's for
later
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>