All current pcie controllers unconditionally use SDR to check the link and
poll for reset.  Refactor the code to include device reset in the
port_init_hw() op and add a new check_link() op.

This will make room fro new controllers that do not use SDR for these
operations.

Tested on 460ex.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

gcc 4.7 will be more strict about parsing the -mtraceback option:

 gcc: error: unrecognized argument in option '-mtraceback=none'
 gcc: note: valid arguments to '-mtraceback=' are: full no part

gcc used to do a 2 char compare so both "no" and "none" would
match. Switch to using -mtraceback=no should work everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds support for the new "jump label" feature.

Unlike x86 and sparc we just merrily patch the code with no locks etc,
as far as I know this is safe, but I'm not really sure what the x86/sparc
code is protecting against so maybe it's not.

I also don't see any reason for us to implement the poke_early() routine,
even though sparc does.

[BenH: Updated the patch to upstream generic changes]
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

A mix of think & mismerge on my side caused a problem where both the
new hvsi_lib and the old hvsi driver gets compiled and try to define
symbols with the same name.

This fixes it by renaming the hvsi_lib exported symbols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

a9c0f41b breaks the build
on some platforms. The extern declaration must be shielded
against assembly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds a printk companion to replace the udbg progress function
when initmem is freed.
Suggested-by: Milton Miller <miltonm@bga.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The free_initmem function is basically duplicated in mm/init_32,
and init_64, and is moved to the common 32/64-bit mm/mem.c.

All other sections except init were removed in v2.6.15 by
6c45ab99 (powerpc: Remove section
free() and linker script bits), and therefore the bulk of the executed
code is identical.

This patch also removes updating ppc_md.progress to NULL in the powermac
late_initcall.
Suggested-by: Milton Miller <miltonm@bga.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: increase rom size for atrm method

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: caam - fix operator precedence in shared descriptor allocation

The vbios rom is >64k on a lot of modern asics.  Increase
the fetch size for atrm to make sure we don't miss part
of a larger rom.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

setkey allocates 16 bytes (CAAM_CMD_SZ *
DESC_AEAD_SHARED_TEXT_LEN) shy of what is needed to
store the shared descriptor, resulting in memory
corruption.  Fix this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86 emulator: fix %rip-relative addressing with immediate source operand

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c/pca954x: Initialize the mux to disconnected state
  i2c-taos-evm: Fix log messages

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  arch/powerpc: use printk_ratelimited instead of printk_ratelimit
  powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
  powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
  powerpc/e500: fix breakage with fsl_rio_mcheck_exception
  powerpc/p1022ds: fix audio-related properties in the device tree
  powerpc/85xx: fix NAND_CMD_READID read bytes number

It's not so much an error as a warning about normal Marvell crazines.
So don't use KERN_ERR that ends up spamming the console even in quiet
mode, it's not _that_ critical.

Explained by Jeff:

 "Long explanation, it's a mess:

  Marvell took standard AHCI, and bastardized it to include a weird mode
  whereby PATA devices appear inside the AHCI DMA and interrupt
  infrastructure you're familiar with.

  So, PATA devices appear via pata_marvell driver, using basic legacy
  IDE programming interface.  But SATA devices, which might also be
  attached to this chip, either work in under-performing mode or
  simply don't work at all (e.g.  newer 6 Gbps devices or port
  multiplier attachments, NCQ, ...)

  On the other hand, 'ahci' driver loads and works with the chip's
  attached SATA devices quite beautifully, but is completely unable to
  drive any attached PATA devices, due to the Marvell-specific
  PATA-under-AHCI interface.

  The "masking port_map 0x7 -> 0x3" message is the ahci driver "hiding"
  the PATA port(s) from itself, making sure it will only drive the SATA
  ports it knows how to drive."
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default. This is bad.

Scenario:
            -- pca954x @ 0x70 -- ch 0 (I2C-bus-101) -- EEPROM @ 0x50
            |
I2C-bus-1 ---
            |
            -- pca954x @ 0x71 -- ch 0 (I2C-bus-111) -- EEPROM @ 0x50

1. Load I2C bus driver: creates I2C-bus-1
2. Load pca954x driver: creates virtual I2C-bus-101 and I2C-bus-111
3. Load eeprom driver
4. Try to read EEPROM @ 0x50 on I2C-bus-101. The transaction will also bleed
   onto I2C-bus-111 because pca954x @ 0x71 channel 0 is connected by default.

Fix: Initialize pca954x to disconnected state in pca954x_probe()
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

* Print all error and information messages even when debugging is
  disabled.
* Don't use adapter device to log messages before it is ready.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

This will allow a different backend to share it
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.

The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.

We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).

However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.

This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:

 - It now supports HVSI as well
 - We add support for hvc backend providing tiocm{get,set}
 - It also provides a udbg interface for early debug and boot console

This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.

In addition to producing generally simler code, this has several benefits
over our current situation:

 - The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past

 - The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).

I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:

 - I clear DTR on close if HUPCL is set

 - Current hvsi triggers a hangup if it detects a up->down transition
   on CD (you can still open a console with CD down). My new implementation
   triggers a hangup if the link to the FSP is severed, and severs it upon
   detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When CONFIG_PPC_EARLY_DEBUG is set, call register_early_udbg_console()
early from generic code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Embed the struct hvsi_header in the various packet definitions
rather than open coding it multiple times. Will help provide
stronger type checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This moves various HVSI protocol definitions from the hvsi.c
driver to a header file that can be used later on by a udbg
implementation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently Maple setup code creates cpc925_edac device only on
Motorola ATCA-6101 blade. Make setup code check bridge revision
and enable EDAC on all U3H bridges.

Verified on Momentum MapleD (ppc970fx kit) board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Reconfiguration notifier call for device node may fail by several reasons,
but it always assumes kmalloc failures.

This enables reconfiguration notifier call chain to get the actual error
code rather than -ENOMEM by converting all reconfiguration notifier calls
to return encapsulate error code with notifier_from_errno().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This introduces pSeries_reconfig_notify() as a just wrapper of
blocking_notifier_call_chain() for pSeries_reconfig_chain.

This is a preparation to improvement of error code on reconfiguration
notifier failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Enable functions used to access SCOM if PPC_MAPLE is defined: they are
used by cpufreq driver to control hardware.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This has been broken for a while but hasn't been an issue until
now because nobody was reserving regions at high addresses.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On MMUs such as FSL where we can guarantee the entire linear mapping is
bolted, we don't need to worry about linear TLB misses.  If on top of
that we do a full table walk, we get rid of all recursive TLB faults, and
can dispense with some state saving.  This gains a few percent on
TLB-miss-heavy workloads, and around 50% on a benchmark that had a high
rate of virtual page table faults under the normal handler.

While touching the EX_TLB layout, remove EX_TLB_MMUCR0, EX_TLB_SRR0, and
EX_TLB_SRR1 as they're not used.

[BenH: Fixed build with 64K pages (wsp config)]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

%rip-relative addressing is relative to the first byte of the next instruction,
so we need to add %rip only after we've fetched any immediate bytes.

Based on original patch by Li Xin <xin.li@intel.com>.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Li Xin <xin.li@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Don't use printk_ratelimit() as an additional condition for returning
on an error. Because when the ratelimit is reached, printk_ratelimit
will return 0 and e.g. in rtas_get_boot_time won't check for an error
condition.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by:
  37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards

causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Use chipset-specific irq installers
  drm/i915: forcewake fix after reset
  drm/i915: add Ivy Bridge page flip support
  drm/i915: split page flip queueing into per-chipset functions

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Connector: Correctly set the error code in case of success when dispatching receive callbacks
  Connector: Set the CN_NETLINK_USERS correctly
  pti: PTI semantics fix in pti_tty_cleanup.
  pti: ENXIO error case memory leak PTI fix.
  pti: double-free security PTI fix
  drivers:misc: ti-st: fix skipping of change remote baud
  drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
  st_kim: Handle case of no device found for ID 0
  firmware: fix GOOGLE_SMI kconfig dependency warning

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  MAINTAINERS: add myself as maintainer of USB/IP
  usb: r8a66597-hcd: fix cannot detect low/full speed device
  USB: ehci-ath79: fix a NULL pointer dereference
  USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
  usb/isp1760: Fix bug preventing the unlinking of control urbs
  USB: Fix up URB error codes to reflect implementation.
  xhci: Always set urb->status to zero for isoc endpoints.
  xhci: Add reset on resume quirk for asrock p67 host
  xHCI 1.0: Incompatible Device Error
  USB: don't let errors prevent system sleep
  USB: don't let the hub driver prevent system sleep
  USB: change maintainership of ohci-hcd and ehci-hcd
  xHCI 1.0: Force Stopped Event(FSE)
  xhci: Don't warn about zeroed bMaxBurst descriptor field.
  USB: Free bandwidth when usb_disable_device is called.
  xhci: Reject double add of active endpoints.
  USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
  usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
  usb: musb: host: compare status for negative error values

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
  amba pl011: platform data for reg lockup and glitch v2
  amba pl011: workaround for uart registers lockup
  tty: n_gsm: improper skb_pull() use was leaking framed data
  tty: n_gsm: Fixed logic to decode break signal from modem status
  TTY: ntty, add one more sanity check
  TTY: ldisc, do not close until there are readers
  8250: Fix capabilities when changing the port type
  8250_pci: Fix missing const from merges
  ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
  serial: ioremap warning fix for jsm driver.
  8250_pci: add -ENODEV code for Intel EG20T PCH