While pursuing and unrelated issue with 64Mb granules I noticed a problem
related to inconsistent use of add_active_range.  There doesn't appear any
reason to me why FLATMEM versus DISCONTIG_MEM should register memory to
add_active_range with different code.  So I've changed the code into a
common implementation.

The other subtle issue fixed by this patch was calling add_active_range in
count_node_pages before granule aligning is performed.  We were lucky with
16MB granules but not so with 64MB granules.  count_node_pages has reserved
regions filtered out and as a consequence linked kernel text and data
aren't covered by calls to count_node_pages.  So linked kernel regions
wasn't reported to add_active_regions.  This resulted in free_initmem
causing numerous bad_page reports.  This won't occur with this patch
because now all known memory regions are reported by
register_active_ranges.
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Don't force CONFIG_SWIOTLB on when not actually needed (i.e. HP_ZX1 and
SGI_SN2).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

The shub2 error interrupt handler must check for TIO errors.

Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>

This function doesn't exist.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

When we offline a CPU, migrate_irqs() tries to determine whether the
affinity bits of the IRQ descriptor match any of the remaining online
CPUs.  If not, it fixes up the interrupt to point somewhere else.
Unfortunately, if an IRQ is unregistered the IRQ descriptor may still
have affinity to the CPU being offlined, but the no_irq_chip handler
doesn't provide a set_affinity function.  This causes us to hit the
WARN_ON in migrate_irqs().

The easiest solution seems to be setting all the bits in the affinity
mask when the last interrupt is removed from the vector.  I hit this on
an older kernel with Xen/ia64 using driver domains (so it probably needs
more testing on upstream).  Xen essentially uses the bind/unbind
interface in sysfs to unregister a device from a driver and thus
unregister the interrupt.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

All IA64 systems except IA64_HP_SIM include ACPI and PCI.
So prevent IA64 Kconfigs that try to do irritating things like building
PCI without building ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch fixes a NULL-pointer dereference in ia64_machine_kexec().

The variable ia64_kimage is set in machine_kexec_prepare() which is
called from sys_kexec_load(). If kdump wasn't configured before,
ia64_kimage is NULL.  machine_kdump_on_init() passes ia64_kimage() to
machine_kexec() which assumes a valid value.

The patch also adds a few sanity checks for the image to simplify
debugging of similar problems in future.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>

I encountered one problem when running ptrace test case the situation
is this: traced process's syscall parameter needs to be accessed, but
for sys_clone system call with clone_flag (CLONE_VFORK | CLONE_VM |
SIGCHLD) parameter.  This syscall's parameter accessing result is wrong.

The reason is that vforked child process mm point is the same, but
tgid is different. Without this patch find_thread_for_addr will return
vforked process if vforked process is also stopped, but not the thread
which calls vfork syscall.
Signed-off-by: Tony Luck <tony.luck@intel.com>

Some patches have turned up on xen-devel recently to convert strcpy()
to safer alternatives and so forth.  While reviewing those patches
I noticed that the features string building could be cleaned up.

This patch uses snprintf() instead of strcpy() and direct character
pointer manipulation.  It makes the features string building safe and
gets rid of the special case for features output in show_cpuinfo()

Additionally I removed the (int) cast of ARRAY_SIZE, which seems to
serve no purpose.
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

As is pointed out in
http://www.gelato.org/community/view_linear.php?id=1_1036&from=authors&value=Ian%20Wienand#1_1039,
if single step on break instruction, the break fault has higher
priority than the single-step trap. When the break fault handler
is entered, it advances the IP by 1 instruction so break instruction
single-stepping is skipped, actually it is next instruction which
is single stepped.

This patch modifies this, it adds TIF_SINGLESTEP bit for thread
flags, and generate a fake sigtrap when single stepping break
instruction. Test case in attachment can verify this. Any comments
is welcome.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This moves the ia64 implementation of machine_shutdown() from
machine_kexec.c to process.c, which is in keeping with the implelmentation
on other architectures, and seems like a much more appropriate home for it.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Remove the Remove inline declaration of efi_get_pal_addr() as it is
declared in linux/efi.h.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

linux/uaccess.h was being included, but it seems that
really the following includes are needed.

asm/page.h: for __va() and PAGE_SHIFT
asm/uaccess.h: for copy_to_user()

I guess that linux/uaccess.h pulls in both asm/page.h and asm/uaccess.h.
I notices this while backporting the code to xen's linux-2.6.16.33,
which does not have linux/uaccess.h. I'm posting it as I think it is a
correct, though somewhat cosmetic fix.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Fix a typo in the saved_max_pfn description in contig.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Set saved_max_pfn when discontig memory is in use.

This sets up saved_max_pfn when disctontig memory is in use.
This mirrors the code for contig memory.

This patch does not entirely solve the problem of making vmcore work,
however it does appear to be neccessary. Please consider applying.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Kexec support for 2.6.20 on ia64 does not build properly using a config
made up by CONFIG_SMP=n and CONFIG_HOTPLUG_CPU=n:
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

When calling into the EFI firmware, the parameters need to be passed on
the stack. The recent change to use -mregparm=3 breaks x86 EFI support.
This patch is needed to allow the new Intel-based Macs to suspend to ram
(efi.get_time is called during the suspend phase).
Signed-off-by: Frederic Riss <frederic.riss@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

That code doesn't do what its author apparently thought it would do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
  [SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
  [SCSI] qla4xxx: bug fixes
  [SCSI] Fix scsi_add_device() for async scanning

x86-64 is missing these:
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.

Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().

http://marc.theaimsgroup.com/?l=linux-acpi&m=116680983430121&w=2Signed-off-by: John Keller <jpk@sgi.com>
Acked-by: Len Brown <lenb@kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Andrew Vasquez is reporting as-iosched oopses and a 65% throughput
slowdown due to the recent special-casing of direct-io against
blockdevs.  We don't know why either of these things are occurring.

The patch minimally reverts us back to the 2.6.19 code for a 2.6.20
release.

Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Ken Chen <kenchen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We went and named them __NR_sys_foo instead of __NR_foo.

It may be too late to change this, but we can at least add the proper names
now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes up ia64 kexec support for HP rx2620 hardware.  It does
this by skipping migration of already disabled irqs.  This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.

The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch.  This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs.  So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().

The code has been tested on three different ia64 machines, all with good
results.  It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.

More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Zou, Nanhai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

An AIO bug was reported that sleeping function is being called in softirq
context:

BUG: warning at kernel/mutex.c:132/__mutex_lock_common()
Call Trace:
     [<a000000100577b00>] __mutex_lock_slowpath+0x640/0x6c0
     [<a000000100577ba0>] mutex_lock+0x20/0x40
     [<a0000001000a25b0>] flush_workqueue+0xb0/0x1a0
     [<a00000010018c0c0>] __put_ioctx+0xc0/0x240
     [<a00000010018d470>] aio_complete+0x2f0/0x420
     [<a00000010019cc80>] finished_one_bio+0x200/0x2a0
     [<a00000010019d1c0>] dio_bio_complete+0x1c0/0x200
     [<a00000010019d260>] dio_bio_end_aio+0x60/0x80
     [<a00000010014acd0>] bio_endio+0x110/0x1c0
     [<a0000001002770e0>] __end_that_request_first+0x180/0xba0
     [<a000000100277b90>] end_that_request_chunk+0x30/0x60
     [<a0000002073c0c70>] scsi_end_request+0x50/0x300 [scsi_mod]
     [<a0000002073c1240>] scsi_io_completion+0x200/0x8a0 [scsi_mod]
     [<a0000002074729b0>] sd_rw_intr+0x330/0x860 [sd_mod]
     [<a0000002073b3ac0>] scsi_finish_command+0x100/0x1c0 [scsi_mod]
     [<a0000002073c2910>] scsi_softirq_done+0x230/0x300 [scsi_mod]
     [<a000000100277d20>] blk_done_softirq+0x160/0x1c0
     [<a000000100083e00>] __do_softirq+0x200/0x240
     [<a000000100083eb0>] do_softirq+0x70/0xc0

See report: http://marc.theaimsgroup.com/?l=linux-kernel&m=116599593200888&w=2

flush_workqueue() is not allowed to be called in the softirq context.
However, aio_complete() called from I/O interrupt can potentially call
put_ioctx with last ref count on ioctx and triggers bug.  It is simply
incorrect to perform ioctx freeing from aio_complete.

The bug is trigger-able from a race between io_destroy() and aio_complete().
A possible scenario:

cpu0                               cpu1
io_destroy                         aio_complete
  wait_for_all_aios {                __aio_put_req
     ...                                 ctx->reqs_active--;
     if (!ctx->reqs_active)
        return;
  }
  ...
  put_ioctx(ioctx)

                                     put_ioctx(ctx);
                                        __put_ioctx
                                          bam! Bug trigger!

The real problem is that the condition check of ctx->reqs_active in
wait_for_all_aios() is incorrect that access to reqs_active is not
being properly protected by spin lock.

This patch adds that protective spin lock, and at the same time removes
all duplicate ref counting for each kiocb as reqs_active is already used
as a ref count for each active ioctx.  This also ensures that buggy call
to flush_workqueue() in softirq context is eliminated.
Signed-off-by: "Ken Chen" <kenchen@google.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Suparna Bhattacharya <suparna@in.ibm.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: <stable@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this by letting NF_CONNTRACK_H323 depend on (IPV6 || IPV6=n).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

  CC      net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

	sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
	The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: Initialize nbytes for internal sg commands
  libata: Fix ata_busy_wait() kernel docs
  pata_via: Correct missing comments
  pata_atiixp: propogate cable detection hack from drivers/ide to the new driver
  ahci/pata_jmicron: fix JMicron quirk

Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

> Looks like you should use ata_busy_wait() here, rather than reproducing
> the same code again.

It waits in 10uS chunks while 1uS chunks were used in the workaround.
Could indeed do that once I know the fix is right. While I'm at it the
ata_busy_wait kerneldoc is borked so here's a fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The 8237S was added to the chipsets but not to the comments. Fix this
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set.  This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.

The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits.  If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.

This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  spidernet : fix memory leak in spider_net_stop
  e100: fix napi ifdefs removing needed code
  netxen patches

* master.kernel.org:/pub/scm/linux/kernel/git/davem/bnx2-2.6:
  [BNX2]: PHY workaround for 5709 A0.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET_SCHED]: act_ipt: fix regression in ipt action