There is no good reason why we need to go through:

stmmac_xpcs_config_eee
-> stmmac_do_callback
   -> mdio_xpcs_ops->config_eee
      -> xpcs_config_eee

when we can simply call xpcs_config_eee.

priv->hw->xpcs is of the type "const struct mdio_xpcs_ops *" and is used
as a placeholder/synonym for priv->plat->mdio_bus_data->has_xpcs. It is
done that way because the mdio_bus_data pointer might or might not be
populated in all stmmac instantiations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling a function pointer with a single implementation through
struct mdio_xpcs_ops is clunky, and the stmmac_do_callback system forces
this to return int, even though it always returns zero.

Simply remove the "validate" function pointer from struct mdio_xpcs_ops
and replace it with an exported xpcs_validate symbol which is called
directly by stmmac.

priv->hw->xpcs is of the type "const struct mdio_xpcs_ops *" and is used
as a placeholder/synonym for priv->plat->mdio_bus_data->has_xpcs. It is
done that way because the mdio_bus_data pointer might or might not be
populated in all stmmac instantiations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The operating mode of the driver is currently to populate its
struct mdio_xpcs_args::supported and struct mdio_xpcs_args::an_mode
statically in xpcs_probe(), based on the passed phy_interface_t,
and work with those.

However this is not the operation that phylink expects from a PCS
driver, because the port might be attached to an SFP cage that triggers
changes of the phy_interface_t dynamically as one SFP module is
unpluggged and another is plugged.

To migrate towards that model, the struct mdio_xpcs_args should not
cache anything related to the phy_interface_t, but just look up the
statically defined, const struct xpcs_compat structure corresponding to
the detected PCS OUI/model number.

So we delete the "supported" and "an_mode" members of struct
mdio_xpcs_args, and add the "id" structure there (since the ID is not
expected to change at runtime).

Since xpcs->supported is used deep in the code in _xpcs_config_aneg_c73(),
we need to modify some function headers to pass the xpcs_compat from all
callers. In turn, the xpcs_compat is always supplied externally to the
xpcs module:
- Most of the time by phylink
- In xpcs_probe() it is needed because xpcs_soft_reset() writes to
  MDIO_MMD_PCS or to MDIO_MMD_VEND2 depending on whether an_mode is clause
  37 or clause 73. In order to not introduce functional changes related
  to when the soft reset is issued, we continue to require the initial
  phy_interface_t argument to be passed to xpcs_probe() so we can pass
  this on to xpcs_soft_reset().
- stmmac_open() wants to know whether to call stmmac_init_phy() or not,
  and for that it looks inside xpcs->an_mode, because the clause 73
  (backplane) AN modes supposedly do not have a PHY. Because we moved
  an_mode outside of struct mdio_xpcs_args, this is now no longer
  directly possible, so we introduce a helper function xpcs_get_an_mode()
  which protects the data encapsulation of the xpcs module and requires
  a phy_interface_t to be passed as argument. This function can look up
  the appropriate compat based on the phy_interface_t.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xpcs driver has an apparently inadequate structure for the actual
hardware it drives.

These defines and the xpcs_probe() function would suggest that there is
one PHY ID per supported PHY interface type, and the driver simply
validates whether the mode it should operate in (the argument of
xpcs_probe) matches what the hardware is capable of:

	#define SYNOPSYS_XPCS_USXGMII_ID	0x7996ced0
	#define SYNOPSYS_XPCS_10GKR_ID		0x7996ced0
	#define SYNOPSYS_XPCS_XLGMII_ID		0x7996ced0
	#define SYNOPSYS_XPCS_SGMII_ID		0x7996ced0
	#define SYNOPSYS_XPCS_MASK		0xffffffff

but that is not the case, because upon closer inspection, all the above
4 PHY ID definitions are in fact equal.

So it is the same XPCS that is compatible with all 4 sets of PHY
interface types.

This change introduces an array of struct xpcs_compat which is populated
by the single struct xpcs_id instance. It also eliminates the bogus
defines for multiple Synopsys XPCS PHY IDs and replaces them with a
single XPCS_ID, which better reflects the way in which the hardware
operates.

Because we are touching this area of the code anyway, the new array of
struct xpcs_compat, as well as the array of xpcs_id, have been moved
towards the end of the file, since they are variable declarations not
definitions. If whichever of struct xpcs_compat or struct xpcs_id need
to gain a function pointer member in the future, it is easier to
reference functions (no forward declarations needed) if we have the
const variable declarations at the end of the file.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CONFIG_STMMAC_ETH selects CONFIG_PCS_XPCS, so there should be no
situation where the shim should be needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peng Li says:

====================
net: hdlc_cisco: clean up some code style issues

This patchset clean up some code style issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Space prohibited between function name and open parenthesis '('.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unnecessary out of memory message,
to fix the following checkpatch.pl warning:
"WARNING: Possible unnecessary 'out of memory' message"
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add spaces required after the close parenthesis '}'.
Add spaces required after that ','.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the checkpatch error as "foo* bar" and should be "foo *bar",
and "(foo*)" should be "(foo *)".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix some spelling mistakes in comments:
enconding  ==> encoding
ambigous  ==> ambiguous
orignal  ==> original
encyption  ==> encryption
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmytro Linkin says:

====================
devlink: rate objects API

Resending without RFC.

Currently kernel provides a way to change tx rate of single VF in
switchdev mode via tc-police action. When lots of VFs are configured
management of theirs rates becomes non-trivial task and some grouping
mechanism is required. Implementing such grouping in tc-police will bring
flow related limitations and unwanted complications, like:
- tc-police is a policer and there is a user request for a traffic
  shaper, so shared tc-police action is not suitable;
- flows requires net device to be placed on, means "groups" wouldn't
  have net device instance itself. Taking into the account previous
  point was reviewed a sollution, when representor have a policer and
  the driver use a shaper if qdisc contains group of VFs - such approach
  ugly, compilated and misleading;
- TC is ingress only, while configuring "other" side of the wire looks
  more like a "real" picture where shaping is outside of the steering
  world, similar to "ip link" command;

According to that devlink is the most appropriate place.

This series introduces devlink API for managing tx rate of single devlink
port or of a group by invoking callbacks (see below) of corresponding
driver. Also devlink port or a group can be added to the parent group,
where driver responsible to handle rates of a group elements. To achieve
all of that new rate object is added. It can be one of the two types:
- leaf - represents a single devlink port; created/destroyed by the
  driver and bound to the devlink port. As example, some driver may
  create leaf rate object for every devlink port associated with VF.
  Since leaf have 1to1 mapping to it's devlink port, in user space it is
  referred as pci/<bus_addr>/<port_index>;
- node - represents a group of rate objects; created/deleted by request
  from the userspace; initially empty (no rate objects added). In
  userspace it is referred as pci/<bus_addr>/<node_name>, where node name
  can be any, except decimal number, to avoid collisions with leafs.

devlink_ops extended with following callbacks:
- rate_{leaf|node}_tx_{share|max}_set
- rate_node_{new|del}
- rate_{leaf|node}_parent_set

KAPI provides:
- creation/destruction of the leaf rate object associated with devlink
  port
- destruction of rate nodes to allow a vendor driver to free allocated
  resources on driver removal or due to the other reasons when nodes
  destruction required

UAPI provides:
- dumping all or single rate objects
- setting tx_{share|max} of rate object of any type
- creating/deleting node rate object
- setting/unsetting parent of any rate object

Added devlink rate object support for netdevsim driver

Issues/open questions:
- Does user need DEVLINK_CMD_RATE_DEL_ALL_CHILD command to clean all
  children of particular parent node? For example:
  $ devlink port function rate flush netdevsim/netdevsim10/group
- priv pointer passed to the callbacks is a source of bugs; in leaf case
  driver can embed rate object into internal structure and use
  container_of() on it; in node case it cannot be done since nodes are
  created from userspace

v1->v2:
- fixed kernel-doc for devlink_rate_leaf_{create|destroy}()
- s/func/function/ for all devlink port command occurences

v2->v3:
- devlink:
  - added devlink_rate_nodes_destroy() function
- netdevsim:
  - added call of devlink_rate_nodes_destroy() function
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink rate objects section at devlink port documentation.
Add devlink rate support info at netdevsim devlink documentation.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test verifies that netdevsim correctly implements devlink ops callbacks
that set node as a parent of devlink leaf or node rate object.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement new devlink ops that allow setting rate node as a parent for
devlink port (leaf) or another devlink node through devlink API.
Expose parent names to netdevsim debugfs in read only mode.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor DEVLINK_CMD_RATE_{GET|SET} command handlers to support setting
a node as a parent for another rate object (leaf or node) by means of
new attribute DEVLINK_ATTR_RATE_PARENT_NODE_NAME. Extend devlink ops
with new callbacks rate_{leaf|node}_parent_set() to set node as a parent
for rate object to allow supporting drivers to implement rate grouping
through devlink. Driver implementations are allowed to support leafs
or node children only. Invoking callback with NULL as parent should be
threated by the driver as unset parent action.
Extend rate object struct with reference counter to disallow deleting a
node with any child pointing to it. User should unset parent for the
child explicitly.

Example:

$ devlink port function rate add netdevsim/netdevsim10/group1

$ devlink port function rate add netdevsim/netdevsim10/group2

$ devlink port function rate set netdevsim/netdevsim10/group1 parent group2

$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node parent group2

$ devlink port function rate set netdevsim/netdevsim10/group1 noparent
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test verifies that it is possible to create, delete and set min/max tx
rate of devlink rate node on netdevsim VF.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement new devlink ops that allow creation, deletion and setting of
shared/max tx rate of devlink rate nodes through devlink API.
Expose rate node and it's tx rates to netdevsim debugfs.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement support for DEVLINK_CMD_RATE_{NEW|DEL} commands that are used
to create and delete devlink rate nodes. Add new attribute
DEVLINK_ATTR_RATE_NODE_NAME that specify node name string. The node name
is an alphanumeric identifier. No valid node name can be a devlink port
index, eg. decimal number. Extend devlink ops with new callbacks
rate_node_{new|del}() and rate_node_tx_{share|max}_set() to allow
supporting drivers to implement ports rate grouping and setting tx rate
of rate nodes through devlink.
Expose devlink_rate_nodes_destroy() function to allow vendor driver do
proper cleanup of internally allocated resources for the nodes if the
driver goes down or due to any other reasons which requires nodes to be
destroyed.
Disallow moving device from switchdev to legacy mode if any node exists
on that device. User must explicitly delete nodes before switching mode.

Example:

$ devlink port function rate add netdevsim/netdevsim10/group1

$ devlink port function rate set netdevsim/netdevsim10/group1 \
        tx_share 10mbit tx_max 100mbit

Add + set command can be combined:

$ devlink port function rate add netdevsim/netdevsim10/group1 \
        tx_share 10mbit tx_max 100mbit

$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node tx_share 10mbit tx_max 100mbit

$ devlink port function rate del netdevsim/netdevsim10/group1
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test verifies that netdevsim VFs can set and retrieve shared/max tx
rate through new devlink API.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement new devlink ops that allow shared and max tx rate control for
devlink port rate objects (leafs) through devlink API.

Expose rate values of VF ports to netdevsim debugfs.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement support for DEVLINK_CMD_RATE_SET command with new attributes
DEVLINK_ATTR_RATE_TX_{SHARE|MAX} that are used to set devlink rate
shared/max tx rate values. Extend devlink ops with new callbacks
rate_leaf_tx_{share|max}_set() to allow supporting drivers to implement
rate control through devlink.

New attributes are optional. Driver implementations are allowed to
support either or both of them.

Shared rate example:

$ devlink port function rate set netdevsim/netdevsim10/0 tx_share 10mbit

$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_share 10mbit

Max rate example:

$ devlink port function rate set netdevsim/netdevsim10/0 tx_max 100mbit

$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_max 100mbit
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test verifies that all netdevsim VF ports have rate leaf object created
by default.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register devlink rate leaf objects per VF.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow registering rate object for devlink ports with dedicated
devlink_rate_leaf_{create|destroy}() API. Implement new netlink
DEVLINK_CMD_RATE_GET command that is used to retrieve rate object info.
Add new DEVLINK_CMD_RATE_{NEW|DEL} commands that are used for
notifications when creating/deleting leaf rate object.

Rate API is intended to be used for rate limiting of individual
devlink ports (leafs) and their aggregates (nodes).

Example:

$ devlink port show
pci/0000:03:00.0/0
pci/0000:03:00.0/1

$ devlink port function rate show
pci/0000:03:00.0/0: type leaf
pci/0000:03:00.0/1: type leaf
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement callbacks to set/get eswitch mode value. Add helpers to check
current mode.

Instantiate VFs' net devices and devlink ports on switchdev enabling and
remove them on legacy enabling. Changing number of VFs while in
switchdev mode triggers VFs creation/deletion.

Also disable NDO API callback to set VF rate, since it's legacy API.
Switchdev API to set VF rate will be implemented in one of the next
patches.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow creation of netdevsim ports for VFs along with allocations of
corresponding net devices and devlink ports.
Add enums and helpers to distinguish PFs' ports from VFs' ports.

Ports creation/deletion debugfs API intended to be used with physical
ports only.
VFs instantiation will be done in one of the next patches.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define type of ports, which netdevsim driver currently operates with as
PF. Define new port type - VF, which will be implemented in following
patches. Add helper functions to distinguish them. Add helper function
to get VF index from port index.

Add port indexing logic where PFs' indexes starts from 0, VFs' - from
NSIM_DEV_VF_PORT_INDEX_BASE.
All ports uses same index pool, which means that PF port may be created
with index from VFs' indexes range.
Maximum number of VFs, which the driver can allocate, is limited by
UINT_MAX - BASE.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move VFs disabling from device release() to nsim_dev_reload_destroy() to
make VFs disabling and ports removal simultaneous.
This is a requirement for VFs ports implemented in next patches.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently there is no limit to the number of VFs netdevsim can enable.
In a real systems this value exist and used by the driver.
Fore example, some features might need to consider this value when
allocating memory.

Expose max_vfs variable to debugfs as configurable resource. If are VFs
configured (num_vfs != 0) then changing of max_vfs not allowed.
Co-developed-by: Yuval Avnery <yuvalav@nvidia.com>
Signed-off-by: Yuval Avnery <yuvalav@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
Introduce conntrack offloading to the nfp driver

Louis Peens says:

This is the first in a series of patches to offload conntrack
to the nfp. The approach followed is to flatten out three
different flow rules into a single offloaded flow. The three
different flows are:

1) The rule sending the packet to conntrack (pre_ct)
2) The rule matching on +trk+est after a packet has been through
   conntrack. (post_ct)
3) The rule received via callback from the netfilter (nft)

In order to offload a flow we need a combination of all three flows, but
they could be added/deleted at different times and in different order.

To solve this we save potential offloadable CT flows in the driver,
and every time we receive a callback we check against these saved flows
for valid merges. Once we have a valid combination of all three flows
this will be offloaded to the NFP. This is demonstrated in the diagram
below.

	+-------------+                      +----------+
	| pre_ct flow +--------+             | nft flow |
	+-------------+        v             +------+---+
	                  +----------+              |
	                  | tc_merge +--------+     |
	                  +----------+        v     v
	+--------------+       ^           +-------------+
	| post_ct flow +-------+       +---+nft_tc merge |
	+--------------+               |   +-------------+
	                               |
	                               |
	                               |
	                               v
	                        Offload to nfp

This series is only up to the point of the pre_ct and post_ct
merges into the tc_merge. Follow up series will continue
to add the nft flows and merging of these flows with the result
of the pre_ct and post_ct merged flows.

Changes since v2:
- nfp: flower-ct: add zone table entry when handling pre/post_ct flows
    Fixed another docstring. Should finally have the patch check
    environment properly configured now to avoid more of these.
- nfp: flower-ct: add tc merge functionality
    Fixed warning found by "kernel test robot <lkp@intel.com>"
    Added code comment explaining chain_index comparison

Changes since v1:
- nfp: flower-ct: add ct zone table
    Fixed unused variable compile warning
    Fixed missing colon in struct description
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add merging of pre/post_ct flow rules into the tc_merge table.
Pre_ct flows needs to be merge with post_ct flows and vice versa.

This needs to be done for all flows in the same zone table, as well
as with the wc_zone_table, which is for flows masking out ct_zone
info.

Cleanup is happening when all the tables are cleared up and prints
a warning traceback as this is not expected in the final version.
At this point we are not actually returning success for the offload,
so we do not get any delete requests for flows, so we can't delete
them that way yet. This means that cleanup happens in what would
usually be an exception path.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the table required to store the merge result of pre_ct and post_ct
flows. This is just the initial setup and teardown of the table,
the implementation will be in follow-up patches.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a hashtable which contains entries to map flow cookies to ct
flow entries. Currently the entries are added and not used, but
follow-up patches will use this for stats updates and flow deletes.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit starts adding the structures and lists that will
be used in follow up commits to enable offloading of conntrack.
Some stub functions are also introduced as placeholders by
this commit.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Start populating the pre/post_ct handler functions. Add a zone entry
to the zone table, based on the zone information from the flow. In
the case of a post_ct flow which has a wildcarded match on the zone
create a special entry.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add initial zone table to nfp_flower_priv. This table will be used
to store all the information required to offload conntrack.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>