Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Cc: Hunyue Yau <hyau@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

board-omap3touchbook.c adds an LCD device, but the kernel doesn't
contain a driver for the device. So let's remove the unneeded LCD
device.

Cc: Gregoire Gentil <gregoire@gentil.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

RX51 uses the new DSS2 display driver, but the board file still
contained some code for the old omapfb driver. The old code can be
removed.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

An on-board projector named picodlp is available for OMAP4430 SDP.

Entry for this picodlp as a panel is being added in dss_devices array to
the board file.  It needs 4 GPIO pins for interfacing with host
processor and these are defined and two of them are configured in board
file.  Two GPIOs power_on and display_select are configured here.
picodlp also needs an i2c client over i2c controller-2 at address 0x1b.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP has two Taal DSI panels, connected to DSI 1 and DSI 2 modules.
The panels use a common PWM backlight, which will be implemented later
when the PWM driver has been improved to support the backlight.

Until the PWM driver has been improved, the following hack added to
arch/arm/mach-omap2/board-4430sdp.c can be used to set the backlight to
max:

static int omap_4430sdp_hack_backlight(void)
{
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2OFF);
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2ON);
       twl_i2c_write_u8(TWL6030_MODULE_ID1, 0x30, TWL6030_TOGGLE3);
       return 0;
}
late_initcall(omap_4430sdp_hack_backlight);
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP board file contains some unused old LCD configurations. They are
not used and can be removed.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.

This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add support to dump the HDMI wrapper, core, PLL and PHY registers
through debugfs.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add some of the missing register definitions, which are h/w indexable.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Remove usage of hdmi_reg struct to use u16 instead in the HDMI IP header
file. hdmi_reg struct is not really needed, and the same change was also
made for dispc earlier.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Move the comments in AVI infoframe structure above each parameter
to align with other comments in the header file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).

That said, the new driver works fine for basic use.

Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Port the old omapfb panel driver for Apollon to DSS2.

Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Port the old omapfb panel driver for H4 to DSS2.

Cc: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Port the old omapfb panel driver for 2430SDP to DSS2.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drivers/video/omap/ contains some lcd drivers which are not used by any
board. They can be removed.

Cc: Arun C <arunedarath@mistralsolutions.com>
Acked-by: Koen Kooi <koen@openembedded.org>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.

The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.

This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Move DISPC scaling related code from dispc_ovl_setup() to a new function
dispc_ovl_calc_scaling(). Use overlay caps to check if the overlay can scale or
not. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The function calc_fclk_five_taps() uses a fixed value of pixels per line which
is used in calculations to get the minimum fclk needed for scaling with five
taps to work.

Remove this by providing the width of the panel connected to the manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dispc_mgr_pclk_rate() is used to calculate minimum required functional clock for
scaling in calc_fclk() and calc_fclk_five_taps(). This function returns the
correct pixel clock for LCD and LCD2 managers, but not for TV manager. Extend
this function so that it gets the correct pixel clock for TV manager.

This also prevents the crash we get when we try to scale overlays connected to
TV manager. The current code leads to a BUG() being executed if we call
dispc_mgr_pclk_rate() for the TV manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Create a helper function called dispc_mgr_is_lcd() which returns true if the
manager is LCD or LCD2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dispc_ovl_enable_replication() and dispc_ovl_set_fifo_threshold() are currently
called in configure_overlay(). These are the only functions which cause DISPC
register writes of overlay parameters outside of dispc_ovl_setup().

Move these to dispc_ovl_setup() and pass replication, fifo_low and fifo_high
thresholds as arguments to dispc_ovl_setup() in order to be aligned with other
overlay parameters. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dispc_ovl_setup() currently takes a large number of overlay arguments, most of
these are members of the overlay_info struct. Replace these arguments by
passing a overlay_info pointer instead.

In configure_overlay(), we create an overlay_info struct called new_oi, this is
a copy of the overlay cache's overlay_info member. Update the new_oi parameters
which could have been possibly changed in configure_overlay(). Pass its pointer
pointer to dispc_ovl_setup().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use the new read_edid() function to get EDID information from the
display (when available), and use the information to use a suitable mode
at initialization time.

Hot-plug is not yet supported, so the timings selected at init time will
stay even if the monitor would be changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add i2c bus number for DVI output for boards with DVI output where the
i2c bus has been confirmed to be connected and working. The driver uses
this to detect if a panel is connected and to read EDID.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Remove the "generic" panel config entry, which is not used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3 Stalker board has definitions for LCD, but uses the generic driver
without any information what kind of LCD it has. The board should use a
particular panel type from panel-generic-dpi driver, not the generic
one.

As I haven't gotten response the signer-off of stalker board about the
issue, this patch removes the LCD support from the board file. This will
allow us to clean up the panel-generic-dpi driver and make it support
only fixed size panels.

CC: Jason Lam <lzg@ema-tech.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Multiple OMAP3/4 boards have a DVI framer output. This patch makes the
boards use the new panel-dvi driver, instead of the panel-generic-dpi
driver.

Separate drivers for fixed size panels and DVI framer gives us cleaner
driver code.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.

The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).

Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Implement detect() by checking the hot plug detect status.

The implementation is not very good, as it always turns on the HDMI
output to get the detection working. HDMI driver needs improvements so
that we could enable only core parts of it.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

check_timings() is supposed to be used to verify if timings are ok or
not. Currently the HDMI driver prints error messages if the timings are
not ok. This is not right, as it is no error to give invalid timings to
check_timings().

Remove the error prints.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Clean up reading of EDID by passing direct address to the block being
read, instead of start address of the whole EDID memory area. Rewrite
the loop which reads the EDID.

This also fixes the checksum calculation, which used to calculate the
checksum only for the first block.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Split the DDC initialization off from hdmi_core_ddc_edid() into a
separate function hdmi_core_ddc_init(). This cleans up the
implementation.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAPFB handles EDID parsing now, using the common helper functions in
fbdev. We can remove the EDID parsing from HDMI driver.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Implement read_edid() for HDMI by implementing necessary functions to
hdmi.c and to hdmi_omap4_panel.c.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Currently the set_timings code for hdmi is quite strange. The display is
disabled in hdmi_omap4_panel.c before setting timings, and enabled in
hdmi.c after setting the timings. Furthermore, the timings were not
permanent, and disabling and enabling the display would lose them.

This patch makes the set_timings handling a bit better.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

detect() can be used to probe if the display is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

read_edid() can be used to get the EDID information from the display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>