- 14 May, 2012 40 commits
-
-
Laurent Pinchart authored
Use the GPIO from the sensor driver instead of calling back to board code. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
Instead of passing a color/monochrome flag through platform data, rely on the I2C device name to identify the chip model. Signed-off-by:
-
Antti Palosaari authored
Add all known reference design USB IDs. Rename two earlier reference design USB IDs. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
We can use tuner ID instead of HW not supported flag. Lesser code is better code. Signed-off-by:
-
Antti Palosaari authored
Fixes most problems when having more than one device connected as demod and tuner configurations are not shared. Signed-off-by:
-
Hans-Frieder Vogt authored
af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt: - bit_cnt is always 0x2710 (10000) - abort_cnt is between 0 and 0x2710 - err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8) in the current implementation BER is calculated as the number of bit errors per processed bits, ignoring those bits that are already discarded and counted in abort_cnt, i.e. UCBLOCKS. Signed-off-by:
Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by:
-
Hans-Frieder Vogt authored
Signed-off-by:
-
Antti Palosaari authored
Not used anymore since new firmware downloader. I forget to remove those earlier when changed firmware downloader. Signed-off-by:
-
Antti Palosaari authored
Fix USB buffer len to maximum possible. Various log writing fixes, remove extra new lines and excessive type casts. Rename and type change some variables. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Sylwester Nawrocki authored
When setting TRY crop on the sub-device the mutex was erroneously acquired rather than released on exit path. This bug is present in kernels starting from v3.2. Cc: stable@vger.kernel.org Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Antonio Ospite authored
Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Antonio Ospite authored
Move drivers/input/fixp-arith.h to include/linux so that the functions defined there can be used by other subsystems, for instance some video devices ISPs can control the output HUE value by setting registers for sin(HUE) and cos(HUE). Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Antonio Ospite authored
Also merge the "COLORS" control into it as it was V4L2_CID_SATURATION anyway. Signed-off-by:
-
Hans de Goede authored
Enabling vflip leads to a much better image, with vflip disabled the image looks washed out as if there is a too high brightness setting. Since we don't know how to lower the brightness setting when not vflipping, simply always vflip and tell userspace to flip the image back, resulting in a much better (less washed out) image. Since the image is now no longer too bright, also modify the luminance level the auto-gain algorithm aims for. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Our init sequence was not setting the register page to point to bank 1 before setting what should be the control reg. This causes the camera to sometimes have its LED on after init. First selecting register bank 1, rather then assuming the current register bank is bank 1, fixes this. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Now that the pac207 driver has been converted to the control framework, there are no remaining users. Signed-off-by:
-
Hans de Goede authored
The pac207's exposure control is a clock-divider, so it goes with quite big steps. So lets use an autogain algorithm optimised for that. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
We intend to eventually port all sub-drivers to the control-framework. At which point it will make more sense to have the ctrl_handler in gspca_dev then to have it in the subdrivers. Lets move it there now, to avoid a lot of work to move it later. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans de Goede authored
Now that stv06xx is using the control framework it is no longer necessary to have a (non const) copy of sd_desc inside the sd specific data struct. Signed-off-by:
-
Hans Verkuil authored
HdG: 1) Let the gspca-core cleanup the controls on control-init error, like with the other converted sub drivers 2) Note this also fixes a bug in the hdcs1020 support which was wrongly reporting an exposure range of 0-65535, even though the effective range was only 0-255 Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans Verkuil authored
HdG: Small fix: don't register some controls for sensors which don't have an implementation for them. Signed-off-by:
-
Hans Verkuil authored
The initial version was done by HV, corrections were made by HdG, and some final small changes again by HV. Signed-off-by:
-
Hans de Goede authored
Even with BRC the highest quality setting is not usable, BRC strips so much data from each MCU that the quality becomes worse then using a lower quality setting to begin with. Signed-off-by:
-
Hans de Goede authored
Always automatically adjust the Bit Rate Control setting as needed, independent of the sensor type. BRC is needed to not run out of bandwidth with higher quality settings independent of the sensor. Also only automatically adjust BRC, and don't adjust the JPEG quality control automatically, as that is not needed and leads to ugly flashes when it is changed. Note that before this patch-set the quality was never changed either due to the bugs in the quality handling fixed in previous patches in this set. Signed-off-by:
-
Hans de Goede authored
The current code is using bits 0-1 of register 8 of the zc3xx controller to set the JPEG quality, but the correct bits are bits 1-2. Bit 0 selects between truncation or rounding in the quantization phase of the compression, since rounding generally gives better results it should thus always be 1. This patch also corrects the quality percentages which belong to the 4 different settings. Last this patch removes the different reg 8 defaults depending on the sensor type. Some of them where going for a default quality setting of 50%, which generally is not necessary in any way and results in poor image quality. 75% is a good default to use for all scenarios. Signed-off-by:
-
Hans de Goede authored
When the user changes the JPEG quality while the camera is streaming, the driver should not only change the JPEG headers send to userspace, but also actually tell the camera to use a different quantization table. Signed-off-by:
-
Hans de Goede authored
The sensor specific dev_post_unset_alt functions all try to write to the bridge, and none free any memory, so they should be skipped if stop0 is called on disconnection. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Just a small cleanup. Signed-off-by:
-
Hans de Goede authored
This is necessary to ensure that worker-threads accessing the device are stopped before our disconnect handler returns. This causes a problem with stream_off calling sd_stop0 a second time when the device handle is closed. This is fixed by setting gscpa_dev->streaming to 0 on disconnect. Note that now stream_off will never be called on a disconnected device, and the present check can thus be removed from stream_off. Signed-off-by:
-
Hans de Goede authored
So that we don't start a read stream when an app is only polling for control events. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans Verkuil authored
Due to latency concerns the VIDIOC_QBUF, DQBUF and QUERYBUF do not use the core lock, instead they rely only on queue_lock. Changes by HdG: 1) Change release from the video_device to the v4l2_device, to avoid a race on disconnect. 2) Adjust for the V4L2 core changes which cause non ioctl fops to no longer take the V4L2 core lock. [mchehab@redhat.com: fix a merge conflict] Signed-off-by:
-
Hans Verkuil authored
There are two bugs here: first the calls to stop0 (in gspca_suspend) and gspca_init_transfer (in gspca_resume) need to be called with the usb_lock held. That's true for the other places they are called and it is what subdrivers expect. Quite a few will unlock the usb_lock in stop0 while waiting for a worker thread to finish, and if usb_lock isn't held then that can cause a kernel oops. The other problem is that a worker thread needs to detect that it has to halt due to a suspend. Otherwise it will just go on looping. So add tests against gspca_dev->frozen in the worker threads that need it. Hdg, 2 minor changes: 1) The finepix device is ok with stopping reading a frame halfway through, so add frozen checks in all places where we also check if we're still streaming 2) Use gspca_dev->dev instead of gspca_dev->present to check for disconnect in all touched drivers. I plan to do this everywhere in the future, and most relevant lines in the touched drivers are already modified by this patch. Signed-off-by:
-
