- 04 Apr, 2024 40 commits
-
-
Somnath Kotur authored
Change bnxt_rx_xdp() to take a pointer to xdp instead of stack variable. This is in prepartion for the XDP metadata patch change where the BPF program can change the value of the xdp.meta_data. Signed-off-by:
Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by:
Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Jesper Dangaard Brouer <hawk@kernel.org> Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240402093753.331120-5-pavan.chebbi@broadcom.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Somnath Kotur authored
Driver's Page Pool allocation code looks at the node local to the PCIe device to determine where to allocate memory. In scenarios where the core count per NUMA node is low (< default rings) it makes sense to exhaust page pool allocations on Node 0 first and then moving on to allocating page pools for the remaining rings from Node 1. With this patch, and the following configuration on the NIC $ ethtool -L ens1f0np0 combined 16 (core count/node = 12, first 12 rings on node#0, last 4 rings node#1) and traffic redirected to a ring on node#1 , we see a performance improvement of ~20% Signed-off-by:
-
Somnath Kotur authored
Enable XPS on default during NIC open. The choice of Tx queue is based on the CPU executing the thread that submits the Tx request. The pool of Tx queues will be spread evenly across both device-attached NUMA nodes(local) and remote NUMA nodes. Signed-off-by:
-
Vikas Gupta authored
In case of DPC, after issuing the hot reset, the kernel waits for 100ms for the device to complete the reset. However on some older chips, the firmware may take up to 1 second to complete the reset, only after which the driver can restart the card. Introduce delay of 900ms to handle this scenario on the older chipsets. Signed-off-by:
Vikas Gupta <vikas.gupta@broadcom.com> Reviewed-by:
-
linke li authored
In mtk_flow_entry_update_l2, the hwe->ib1 is read using READ_ONCE at the beginning of the function, checked, and then re-read from hwe->ib1, may void all guarantees of the checks. Reuse the value that was read by READ_ONCE to ensure the consistency of the ib1 throughout the function. Signed-off-by:
linke li <lilinke99@qq.com> Link: https://lore.kernel.org/r/tencent_C699E9540505523424F11A9BD3D21B86840A@qq.comSigned-off-by:
-
Nikita Kiryushin authored
As of now, tg3_power_down_prepare always ends with success, but the error handling code from former tg3_set_power_state call is still here. This code became unreachable in commit c866b7ea ("tg3: Do not use legacy PCI power management"). Remove (now unreachable) error handling code for simplification and change tg3_power_down_prepare to a void function as its result is no more checked. Signed-off-by:
Nikita Kiryushin <kiryushin@ancud.ru> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240401191418.361747-1-kiryushin@ancud.ruSigned-off-by:
-
Jakub Kicinski authored
Petr Machata says: ==================== mlxsw: Preparations for improving performance Amit Cohen writes: mlxsw driver will use NAPI for event processing in a next patch set. Some additional improvements will be added later. This patch set prepares the code for NAPI usage and refactor some relevant areas. See more details in commit messages. Patch Set overview: Patches #1-#2 are preparations for patch #3 Patch #3 setups tasklets as part of queue initializtion Patch #4 removes handling of unlikely scenario Patch #5 removes unused counters Patch #6 makes style change in mlxsw_pci_eq_tasklet() Patch #7-#10 poll command interface instead of EQ0 usage Patches #11-#12 make style change and break the function mlxsw_pci_cq_tasklet() Patches #13-#14 remove functions which can be replaced by a stored value Patch #15 improves accessing to descriptor queue instance ==================== Link: https://lore.kernel.org/r/cover.1712062203.git.petrm@nvidia.comSigned-off-by:
-
Amit Cohen authored
Currently, for each completion, we check the number of descriptor queue and take it via mlxsw_pci_{sdq,rdq}_get(). This is inefficient, the DQ should be the same for all the completions in CQ, as each CQ handles only one DQ - SDQ or RDQ. This mapping is handled as part of DQ initialization via mlxsw_cmd_mbox_sw2hw_dq_cq_set(). Instead, as part of DQ initialization, set DQ pointer in the appropriate CQ structure. When we handle completions, warn in case that the DQ number that we expect is different from the number we get in the CQE. Call WARN_ON_ONCE() only after checking the value, to avoid calling this method for each completion. Signed-off-by:Amit Cohen <amcohen@nvidia.com> Reviewed-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
-
Amit Cohen authored
Currently, for each interrupt we call mlxsw_pci_cq_count() to determine the number of CQs. This call makes additional two function's calls. This can be removed by storing this value as part of structure 'mlxsw_pci', as we already do for number of SDQs. Remove the function and __mlxsw_pci_queue_count() which is now not used and store the value instead. Signed-off-by:
-
Amit Cohen authored
The number of SDQs is stored as part of 'mlxsw_pci' structure. In some cases, the driver uses this value and in some cases it calls mlxsw_pci_sdq_count() to get the value. Align the code to use the stored value. This simplifies the code and makes it clearer that the value is always the same. Rename 'mlxsw_pci->num_sdq_cqs' to 'mlxsw_pci->num_sdqs' as now it is used not only in CQ context. Signed-off-by:
-
Amit Cohen authored
Completion queues are used for completions of RDQ or SDQ. Each completion queue is used for one DQ. The first CQs are used for SDQs and the rest are used for RDQs. Currently, for each CQE (completion queue element), we check 'sr' value (send/receive) to know if it is completion of RDQ or SDQ. Actually, we do not really have to check it, as according to the queue number we know if it handles completions of Rx or Tx. Break the tasklet into two - one for Rx (RDQ) and one for Tx (SDQ). Then, setup the appropriate tasklet for each queue as part of queue initialization. Use 'sr' value for unlikely case that we get completion with type that we do not expect. Call WARN_ON_ONCE() only after checking the value, to avoid calling this method for each completion. A next patch set will use NAPI to handle events, then we will have a separate poll method for Rx and Tx. This change is a preparation for NAPI usage. Signed-off-by:
-
Amit Cohen authored
This function will be broken into several functions later. As preparation, reorder variables to reverse xmas tree. Signed-off-by:
-
Amit Cohen authored
The previous patch changed the code to do not handle command interface from event queue. With this change the wait queue is not used anymore. Remove it and 'wait_done' variable. Signed-off-by:
-
Amit Cohen authored
The device supports two event queues. EQ0 is used for command interface completion events. EQ1 is used for completion events of RDQ or SDQ. Currently, for each EQE (event queue element), we check the queue number and handle accordingly. More than that, for each interrupt we schedule tasklets for both EQs. This is really ineffective, especially because of the fact that EQ0 is used only as part of driver init/fini, when EMADs are not available. There is no point to schedule the tasklet for it and check each EQE. A previous patch changed the code to poll command interface for each use of it. It means that now there is no real reason to use EQ0, as we poll the command interface. Initialize only one event queue and use it as EQ1 (this is determined by queue number). Then, for each interrupt we can schedule the tasklet only for one queue and we do not have to check the queue number. This simplifies the code and should improve performance. Note that polling command interface is ok as we use it only as part of driver init/fini. Signed-off-by:
-
Amit Cohen authored
Currently we use MLXSW_PCI_EQS_COUNT event queues. A next patch will change the driver to initialize only EQ1, as EQ0 is not required anymore when we poll command interface. Rename the macro to MLXSW_PCI_EQS_MAX as later we will not initialize the maximum supported EQs, this value represents the maximum and a new macro will be added to represent the actual used queues. Signed-off-by:
-
Amit Cohen authored
Command interface is used for configuring and querying FW when EMADs are not available. During the time that the driver sets up the asynchronous queues, it polls the command interface for getting completions. Then, there is a short period when asynchronous queues work, but EMADs are not available (marked in the code as nopoll = true). During this time, we send commands via command interface, but we do not poll it, as we can get an interrupt for the completion. Completions of command interface are received from HW in EQ0 (event queue 0). The usage of EQ0 instead of polling is done only 4 times during initialization and one time during tear down, but it makes an overhead during lifetime of the driver. For each interrupt, we have to check if we get events in EQ0 or EQ1 and handle them. This is really ineffective, especially because of the fact that EQ0 is used only as part of driver init/fini. Instead, we can poll command interface for each call of cmd_exec(). It means that when we send a command via command interface (as EMADs are not available), we will poll it, regardless of availability of the asynchronous queues. This will allow us to configure later only EQ1 and simplify the flow. Remove 'nopoll' indication and change mlxsw_pci_cmd_exec() to poll till answer/timeout regardless of queues' state. For now, completions are handled also by EQ0, but it will be removed in next patch. Additional cleanups will be added in next patches. Signed-off-by:
-
Amit Cohen authored
This function will be used later only for EQ1. As preparation, reorder variables to reverse xmas tree and return earlier when it is possible, to simplify the code. Signed-off-by:
-
Amit Cohen authored
The structure 'mlxsw_pci_queue' stores several counters which were consumed via debugfs. Since commit 9a32562b ("mlxsw: Remove debugfs interface"), these counters are not used. Remove them. This makes the 'union u' and 'struct eq' redundant. Maintain 'struct cq' as it will be extended later. Replace increasing 'q->u.eq.ev_other_count' with WARN_ON_ONCE(), as it is used in an unreasonable case of receiving event in EQ which is not EQ0 or EQ1. When the queues are initialized, we check number of event queues and fail with the print "Unsupported number of queues" in case that the driver tries to initialize more than two queues. Signed-off-by:
-
Amit Cohen authored
Currently, as part of mlxsw_pci_cq_tasklet(), we check if any item was handled, and only in such case we arm doorbell. This is unlikely case, as we schedule tasklet only for CQs that we get an event for them, which means that they contain completions to handle. Remove this check, which is supposed to be true always, and even if it is false, it is not a mistake to ring the doorbell. We can warn on such case, but it is not really worth to add a check which will be run for each CQ handling when we do not expect to reach it and it does not point to logic error that should be handled. Signed-off-by:
-
Amit Cohen authored
Currently, the structure 'mlxsw_pci_queue_ops' holds a pointer to the callback function of tasklet. This is used only for EQ and CQ. mlxsw driver will use NAPI in a following patch set, so CQ will not use tasklet anymore. As preparation, remove this pointer from the shared operation structure and setup the tasklet as part of queue initialization. For now, setup tasklet for EQ and CQ. Later, CQ code will be changed. Signed-off-by:
-
Amit Cohen authored
Move mlxsw_pci_cq_{init, fini}() after mlxsw_pci_cq_tasklet() as a next patch will setup the tasklet as part of initialization. Signed-off-by: -
Amit Cohen authored
Move mlxsw_pci_eq_{init, fini}() after mlxsw_pci_eq_tasklet() as a next patch will setup the tasklet as part of initialization. Signed-off-by: -
Jakub Kicinski authored
Tariq Toukan says: ==================== mlx5 misc patches This patchset includes small features and misc code enhancements for the mlx5 core and EN drivers. Patches 1-4 by Gal improves the mlx5e ethtool stats implementation, for example by using standard helpers ethtool_sprintf/puts. Patch 5 by me adds a reset option for the FW command interface debugfs stats entries. This allows explicit FW command interface stats reset between different runs of a test case. Patches 6 and 7 are simple cleanups. Patch 8 by Gal adds driver support for 800Gbps link modes. Patch 9 by Jianbo enhances the L4 steering abilities. Patches 10-11 by Jianbo save redundant operations. ==================== Link: https://lore.kernel.org/r/20240402133043.56322-1-tariqt@nvidia.comSigned-off-by:
-
Jianbo Liu authored
Firmware will return 0 on query BOOT/INIT PAGES for non-page supplier functions (external host PF/VF/SF), so no page is needed to be allocated for them. Signed-off-by:
Jianbo Liu <jianbol@nvidia.com> Reviewed-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Moshe Shemesh <moshe@nvidia.com> Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20240402133043.56322-12-tariqt@nvidia.comSigned-off-by:
-
Jianbo Liu authored
Page events are not issued by device on the function if page_request_disable is set, so no need to create pages EQ. Signed-off-by:
-
Jianbo Liu authored
Replace matching on TCP and UDP protocols with new l4_type field which is parsed by steering for ttc_table. It is enabled by the outer_l4_type or inner_l4_type bits in nic_rx or port_sel flow table capabilities and used only if pcc_ifa2 bit in HCA capabilities is set. Signed-off-by:
Mark Bloch <mbloch@nvidia.com> Signed-off-by:
-
Gal Pressman authored
Add support for 800Gbps speed, link modes of 100Gbps per lane. Signed-off-by:
Gal Pressman <gal@nvidia.com> Reviewed-by:
Cosmin Ratiu <cratiu@nvidia.com> Signed-off-by:
-
Gal Pressman authored
In the kernel, the preferred types are uX. Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
-
Carolina Jubran authored
Starting from commit eb9b9fdc ("net/mlx5e: Introduce extended version for mlx5e_xmit_data") sinfo is no longer passed as an argument to mlx5e_xmit_xdp_frame(), the comment is inconsistent. check_result must be zero when the packet is fragmented. Signed-off-by:
Carolina Jubran <cjubran@nvidia.com> Reviewed-by:
-
Tariq Toukan authored
Resetting stats just before some test/debug case allows us to eliminate out the impact of previous commands. Useful in particular for the average latency calculation. The average_write() callback was unreachable, as "average" is a read-only file. Extend, rename, and use it for a newly exposed write-only "reset" file. Signed-off-by:
-
Gal Pressman authored
The fill_strings() callbacks were changed to accept a **data pointer, and not rely on propagating the index value. Make a similar change to fill_stats() callbacks to keep the API consistent. Signed-off-by:
-
Gal Pressman authored
Use ethtool_sprintf/puts() helper functions which handle the common pattern of printing a string into the ethtool strings interface and incrementing the string pointer by ETH_GSTRING_LEN. Change the fill_strings callback to accept a **data pointer, and remove the index and return value. Signed-off-by:
-
Gal Pressman authored
Use ethtool_sprintf/puts() helper functions which handle the common pattern of printing a string into the ethtool strings interface and incrementing the string pointer by ETH_GSTRING_LEN. The int return value in mlx5e_self_test_fill_strings() is not removed as it is still used to return the number of selftests. Signed-off-by:
-
Gal Pressman authored
Use ethtool_sprintf/puts() helper functions which handle the common pattern of printing a string into the ethtool strings interface and incrementing the string pointer by ETH_GSTRING_LEN. Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.10 The first "new features" pull request for v6.10 with changes both in stack and in drivers. The big thing in this pull request is that wireless subsystem is now almost free of sparse warnings. There's only one warning left in ath11k which was introduced in v6.9-rc1 and will be fixed via the wireless tree. Realtek drivers continue to improve, now we have support for RTL8922AE and RTL8723CS devices. ath11k also has long waited support for P2P. This time we have a small conflict in iwlwifi, Stephen has an example merge resolution which should help with fixing the conflict: https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/ Major changes: rtw89 * RTL8922AE Wi-Fi 7 PCI device support rtw88 * RTL8723CS SDIO device support iwlwifi * don't support puncturing in 5 GHz * support monitor mode on passive channels * BZ-W device support * P2P with HE/EHT support ath11k * P2P support for QCA6390, WCN6855 and QCA2066 * tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits) wifi: mt76: mt7915: workaround dubious x | !y warning wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask net: rfkill: gpio: Convert to platform remove callback returning void wifi: mac80211: use kvcalloc() for codel vars wifi: iwlwifi: reconfigure TLC during HW restart wifi: iwlwifi: mvm: don't change BA sessions during restart wifi: iwlwifi: mvm: select STA mask only for active links wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9 wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces wifi: iwlwifi: mvm: Remove outdated comment wifi: iwlwifi: add support for BZ_W wifi: iwlwifi: Print a specific device name. wifi: iwlwifi: remove wrong CRF_IDs wifi: iwlwifi: remove devices that never came out wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator wifi: iwlwifi: mvm: fix active link counting during recovery wifi: iwlwifi: mvm: assign link STA ID lookups during restart ... ==================== Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.orgSigned-off-by:
-
Rahul Rameshbabu authored
ethtool.py depends on yml files in a specific location of the linux kernel tree. Using relative lookup for those files means that ethtool.py would need to be run under tools/net/ynl/. Lookup needed yml files without depending on the current working directory that ethtool.py is invoked from. Signed-off-by:
Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by:
Dragos Tatulea <dtatulea@nvidia.com> Link: https://lore.kernel.org/r/20240402204000.115081-1-rrameshbabu@nvidia.comSigned-off-by:
-
Pawel Dembicki authored
This commit implements VCT in 88E308X/88E609X Family. It require two workarounds with some magic configuration. Regular use require only one register configuration. But Open Circuit require second workaround. It cause implementation two phases for fault length measuring. Fast Ethernet PHY have implemented very simple version of VCT. It's complitley different than vct5 or vct7. Signed-off-by:
Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240402201123.2961909-3-paweldembicki@gmail.comSigned-off-by:
-
Pawel Dembicki authored
Some PHYs can recognize during a cable test if the impedance in the cable is okay. They can detect reflections caused by impedance discontinuity between a regular 100 Ohm cable and an abnormal part with a higher or lower impedance. This commit introduces a new result code: ETHTOOL_A_CABLE_RESULT_CODE_IMPEDANCE_MISMATCH, which represents the results of a cable test indicating issues with impedance integrity. Signed-off-by:
-
Pawel Dembicki authored
This patch implements only basic support. It covers PHY used in multiple IC: PHY: 88E3082, 88E3083 Switch: 88E6096, 88E6097 Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240402201123.2961909-1-paweldembicki@gmail.comSigned-off-by:
-
Christophe JAILLET authored
In "struct muram_info", the 'size' field is unused. In "struct memac_cfg", the 'fixed_link' field is unused. Remove them. Found with cppcheck, unusedStructMember. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Sean Anderson <sean.anderson@seco.com> Reviewed-by:
-
