On low-effciency embedded platforms, transmission performance is poor
due to on Bulk-out with single packet.
Adding TSO feature improves the transmission performance and reduces
the number of interrupt caused by Bulk-out complete.

Reference to module, net: usb: aqc111.
Signed-off-by: Jacky Chou <jackychou@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matt Johnston says:

====================
MCTP I2C driver

This patch series adds a netdev driver providing MCTP transport over
I2C.

It applies against net-next using recent MCTP changes there, though also
has I2C core changes for review. I'll leave it to maintainers where it
should be applied - please let me know if it needs to be submitted
differently.

The I2C patches were previously sent as RFC though the only feedback
there was an ack to 255 bytes for aspeed.

The dt-bindings patch went through review on the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.

Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.

In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.

The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.

(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)

This driver requires I2C adapters that allow 255 byte transfers
(SMBus 3.0) as the specification requires a minimum MTU of 68 bytes.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Used to define a local endpoint to communicate with MCTP peripherals
attached to an I2C bus. This I2C endpoint can communicate with remote
MCTP devices on the I2C bus.

In the example I2C topology below (matching the second yaml example) we
have MCTP devices on busses i2c1 and i2c6. MCTP-supporting busses are
indicated by the 'mctp-controller' DT property on an I2C bus node.

A mctp-i2c-controller I2C client DT node is placed at the top of the
mux topology, since only the root I2C adapter will support I2C slave
functionality.
                                               .-------.
                                               |eeprom |
    .------------.     .------.               /'-------'
    | adapter    |     | mux  --@0,i2c5------'
    | i2c1       ----.*|      --@1,i2c6--.--.
    |............|    \'------'           \  \  .........
    | mctp-i2c-  |     \                   \  \ .mctpB  .
    | controller |      \                   \  '.0x30   .
    |            |       \  .........        \  '.......'
    | 0x50       |        \ .mctpA  .         \ .........
    '------------'         '.0x1d   .          '.mctpC  .
                            '.......'          '.0x31   .
                                                '.......'
(mctpX boxes above are remote MCTP devices not included in the DT at
present, they can be hotplugged/probed at runtime. A DT binding for
specific fixed MCTP devices could be added later if required)
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

255 byte support has been tested on a npcm750 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

255 byte transfers have been tested on an AST2500 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I2C_SMBUS is limited to 32 bytes due to compatibility with the
32 byte i2c_smbus_data.block

I2C_RDWR allows larger transfers if sufficient sized buffers are passed.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMBus 3.0 increased the maximum block transfer size from 32 bytes to
255 bytes. We increase the size of struct i2c_smbus_data's block[]
member.

i2c_smbus_xfer() and i2c_smbus_xfer_emulated() now support 255 byte
block operations, other block functions remain limited to 32 bytes for
compatibility with existing callers.

We allow adapters to indicate support for the larger size with
I2C_FUNC_SMBUS_V3_BLOCK. Most emulated drivers should be able to use 255
byte blocks by replacing I2C_SMBUS_BLOCK_MAX with I2C_SMBUS_V3_BLOCK_MAX
though some will have hardware limitations that need testing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'inuse' bitmap is local to this function. So we can use the
non-atomic '__set_bit()' to save a few cycles.

While at it, also remove some useless {}.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed comments to match description with variable names and
refactored code to match the convention as per [1].

To match the convention mapping is done as follows:
State 3 - LOST_IN_BURST_PERIOD
State 4 - LOST_IN_GAP_PERIOD

[1] S. Salsano, F. Ludovici, A. Ordine, "Definition of a general
and intuitive loss model for packet networks and its implementation
in the Netem module in the Linux kernel"

Fixes: a6e2fe17 ("sch_netem: replace magic numbers with enumerate")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vsc73xx_remove() returns zero unconditionally and no caller checks the
returned value. So convert the function to return no value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous stmmac_xdp_set_prog() implementation uses stmmac_release()
and stmmac_open() which tear down the PHY device and causes undesirable
autonegotiation which causes a delay whenever AFXDP ZC is setup.

This patch introduces two new functions that just sufficiently tear
down DMA descriptors, buffer, NAPI process, and IRQs and reestablish
them accordingly in both stmmac_xdp_release() and stammac_xdp_open().

As the results of this enhancement, we get rid of transient state
introduced by the link auto-negotiation:

$ ./xdpsock -i eth0 -t -z

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 634444         634560

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632330         1267072

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632438         1899584

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632502         2532160
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This statement is repeated with the initialization statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

there is a same action when the variable is initialized
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assignment in the if statement will be overwritten by the
following statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fix from Herbert Xu:
 "This fixes a boot crash regression"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: api - Fix boot-up crash when crypto manager is disabled

Pull more SCSI updates from James Bottomley:
 "This series is all the stragglers that didn't quite make the first
  merge window pull. It's mostly minor updates and bug fixes of merge
  window code but it also has two driver updates: ufs and qla2xxx"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
  scsi: scsi_debug: Don't call kcalloc() if size arg is zero
  scsi: core: Remove command size deduction from scsi_setup_scsi_cmnd()
  scsi: scsi_ioctl: Validate command size
  scsi: ufs: ufshpb: Properly handle max-single-cmd
  scsi: core: Avoid leaving shost->last_reset with stale value if EH does not run
  scsi: bsg: Fix errno when scsi_bsg_register_queue() fails
  scsi: sr: Remove duplicate assignment
  scsi: ufs: ufs-exynos: Introduce ExynosAuto v9 virtual host
  scsi: ufs: ufs-exynos: Multi-host configuration for ExynosAuto v9
  scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS
  scsi: ufs: ufs-exynos: Add pre/post_hce_enable drv callbacks
  scsi: ufs: ufs-exynos: Factor out priv data init
  scsi: ufs: ufs-exynos: Add EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR option
  scsi: ufs: ufs-exynos: Support custom version of ufs_hba_variant_ops
  scsi: ufs: ufs-exynos: Add setup_clocks callback
  scsi: ufs: ufs-exynos: Add refclkout_stop control
  scsi: ufs: ufs-exynos: Simplify drv_data retrieval
  scsi: ufs: ufs-exynos: Change pclk available max value
  scsi: ufs: Add quirk to enable host controller without PH configuration
  scsi: ufs: Add quirk to handle broken UIC command
  ...

Merge tag 'pwm/for-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "This set is mostly small fixes and cleanups, so more of a janitorial
  update for this cycle"

* tag 'pwm/for-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: vt8500: Rename pwm_busy_wait() to make it obviously driver-specific
  dt-bindings: pwm: tpu: Add R-Car M3-W+ device tree bindings
  dt-bindings: pwm: tpu: Add R-Car V3U device tree bindings
  pwm: pwm-samsung: Trigger manual update when disabling PWM
  pwm: visconti: Simplify using devm_pwmchip_add()
  pwm: samsung: Describe driver in Kconfig
  pwm: Make it explicit that pwm_apply_state() might sleep
  pwm: Add might_sleep() annotations for !CONFIG_PWM API functions
  pwm: atmel: Drop unused header

Pull sound fixes from Takashi Iwai:
 "A collection of fixes for 5.16-rc1, notably for a few regressions that
  were found in 5.15 and pre-rc1:

   - revert of the unification of SG-buffer helper functions on x86 and
     the relevant fix

   - regression fixes for mmap after the recent code refactoring

   - two NULL dereference fixes in HD-audio controller driver

   - UAF fixes in ALSA timer core

   - a few usual HD-audio and FireWire quirks"

* tag 'sound-fix-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: fireworks: add support for Loud Onyx 1200f quirk
  ALSA: hda: fix general protection fault in azx_runtime_idle
  ALSA: hda: Free card instance properly at probe errors
  ALSA: hda/realtek: Add quirk for HP EliteBook 840 G7 mute LED
  ALSA: memalloc: Remove a stale comment
  ALSA: synth: missing check for possible NULL after the call to kstrdup
  ALSA: memalloc: Use proper SG helpers for noncontig allocations
  ALSA: pci: rme: Fix unaligned buffer addresses
  ALSA: firewire-motu: add support for MOTU Track 16
  ALSA: PCM: Fix NULL dereference at mmap checks
  ALSA: hda/realtek: Add quirk for ASUS UX550VE
  ALSA: timer: Unconditionally unlink slave instances, too
  ALSA: memalloc: Catch call with NULL snd_dma_buffer pointer
  Revert "ALSA: memalloc: Convert x86 SG-buffer handling with non-contiguous type"
  ALSA: hda/realtek: Add a quirk for Acer Spin SP513-54N
  ALSA: firewire-motu: add support for MOTU Traveler mk3
  ALSA: hda/realtek: Headset fixup for Clevo NH77HJQ
  ALSA: timer: Fix use-after-free problem

Pull more drm updates from Dave Airlie:
 "I missed a drm-misc-next pull for the main pull last week. It wasn't
  that major and isn't the bulk of this at all. This has a bunch of
  fixes all over, a lot for amdgpu and i915.

  bridge:
   - HPD improvments for lt9611uxc
   - eDP aux-bus support for ps8640
   - LVDS data-mapping selection support

  ttm:
   - remove huge page functionality (needs reworking)
   - fix a race condition during BO eviction

  panels:
   - add some new panels

  fbdev:
   - fix double-free
   - remove unused scrolling acceleration
   - CONFIG_FB dep improvements

  locking:
   - improve contended locking logging
   - naming collision fix

  dma-buf:
   - add dma_resv_for_each_fence iterator
   - fix fence refcounting bug
   - name locking fixesA

  prime:
   - fix object references during mmap

  nouveau:
   - various code style changes
   - refcount fix
   - device removal fixes
   - protect client list with a mutex
   - fix CE0 address calculation

  i915:
   - DP rates related fixes
   - Revert disabling dual eDP that was causing state readout problems
   - put the cdclk vtables in const data
   - Fix DVO port type for older platforms
   - Fix blankscreen by turning DP++ TMDS output buffers on encoder->shutdown
   - CCS FBs related fixes
   - Fix recursive lock in GuC submission
   - Revert guc_id from i915_request tracepoint
   - Build fix around dmabuf

  amdgpu:
   - GPU reset fix
   - Aldebaran fix
   - Yellow Carp fixes
   - DCN2.1 DMCUB fix
   - IOMMU regression fix for Picasso
   - DSC display fixes
   - BPC display calculation fixes
   - Other misc display fixes
   - Don't allow partial copy from user for DC debugfs
   - SRIOV fixes
   - GFX9 CSB pin count fix
   - Various IP version check fixes
   - DP 2.0 fixes
   - Limit DCN1 MPO fix to DCN1

  amdkfd:
   - SVM fixes
   - Fix gfx version for renoir
   - Reset fixes

  udl:
   - timeout fix

  imx:
   - circular locking fix

  virtio:
   - NULL ptr deref fix"

* tag 'drm-next-2021-11-12' of git://anongit.freedesktop.org/drm/drm: (126 commits)
  drm/ttm: Double check mem_type of BO while eviction
  drm/amdgpu: add missed support for UVD IP_VERSION(3, 0, 64)
  drm/amdgpu: drop jpeg IP initialization in SRIOV case
  drm/amd/display: reject both non-zero src_x and src_y only for DCN1x
  drm/amd/display: Add callbacks for DMUB HPD IRQ notifications
  drm/amd/display: Don't lock connection_mutex for DMUB HPD
  drm/amd/display: Add comment where CONFIG_DRM_AMD_DC_DCN macro ends
  drm/amdkfd: Fix retry fault drain race conditions
  drm/amdkfd: lower the VAs base offset to 8KB
  drm/amd/display: fix exit from amdgpu_dm_atomic_check() abruptly
  drm/amd/amdgpu: fix the kfd pre_reset sequence in sriov
  drm/amdgpu: fix uvd crash on Polaris12 during driver unloading
  drm/i915/adlp/fb: Prevent the mapping of redundant trailing padding NULL pages
  drm/i915/fb: Fix rounding error in subsampled plane size calculation
  drm/i915/hdmi: Turn DP++ TMDS output buffers back on in encoder->shutdown()
  drm/locking: fix __stack_depot_* name conflict
  drm/virtio: Fix NULL dereference error in virtio_gpu_poll
  drm/amdgpu: fix SI handling in amdgpu_device_asic_has_dc_support()
  drm/amdgpu: Fix dangling kfd_bo pointer for shared BOs
  drm/amd/amdkfd: Don't sent command to HWS on kfd reset
  ...

Pull input updates from Dmitry Torokhov:
 "Just one new driver (Cypress StreetFighter touchkey), and no input
  core changes this time.

  Plus various fixes and enhancements to existing drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
  Input: iforce - fix control-message timeout
  Input: wacom_i2c - use macros for the bit masks
  Input: ili210x - reduce sample period to 15ms
  Input: ili210x - improve polled sample spacing
  Input: ili210x - special case ili251x sample read out
  Input: elantench - fix misreporting trackpoint coordinates
  Input: synaptics-rmi4 - Fix device hierarchy
  Input: i8042 - Add quirk for Fujitsu Lifebook T725
  Input: cap11xx - add support for cap1206
  Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
  Input: ili210x - add ili251x firmware update support
  Input: ili210x - export ili251x version details via sysfs
  Input: ili210x - use resolution from ili251x firmware
  Input: pm8941-pwrkey - respect reboot_mode for warm reset
  reboot: export symbol 'reboot_mode'
  Input: max77693-haptic - drop unneeded MODULE_ALIAS
  Input: cpcap-pwrbutton - do not set input parent explicitly
  Input: max8925_onkey - don't mark comment as kernel-doc
  Input: ads7846 - do not attempt IRQ workaround when deferring probe
  Input: ads7846 - use input_set_capability()
  ...

Pull RTC updates from Alexandre Belloni:
 "This includes new ioctls to get and set parameters and in particular
  the backup switch mode that is needed for some RTCs to actually enable
  the backup voltage (and have a useful RTC).

  The same interface can also be used to get the actual features
  supported by the RTC so userspace has a better way than trying and
  failing.

  Summary:

  Subsystem:
   - Add new ioctl to get and set extra RTC parameters, this includes
     backup switch mode
   - Expose available features to userspace, in particular, when alarmas
     have a resolution of one minute instead of a second.
   - Let the core handle those alarms with a minute resolution

  New driver:
   - MSTAR MSC313 RTC

  Drivers:
   - Add SPI ID table where necessary
   - Add BSM support for rv3028, rv3032 and pcf8523
   - s3c: set RTC range
   - rx8025: set range, implement .set_offset and .read_offset"

* tag 'rtc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
  rtc: rx8025: use .set_offset/.read_offset
  rtc: rx8025: use rtc_add_group
  rtc: rx8025: clear RTC_FEATURE_ALARM when alarm are not supported
  rtc: rx8025: set range
  rtc: rx8025: let the core handle the alarm resolution
  rtc: rx8025: switch to devm_rtc_allocate_device
  rtc: ab8500: let the core handle the alarm resolution
  rtc: ab-eoz9: support UIE when available
  rtc: ab-eoz9: use RTC_FEATURE_UPDATE_INTERRUPT
  rtc: rv3032: let the core handle the alarm resolution
  rtc: s35390a: let the core handle the alarm resolution
  rtc: handle alarms with a minute resolution
  rtc: pcf85063: silence cppcheck warning
  rtc: rv8803: fix writing back ctrl in flag register
  rtc: s3c: Add time range
  rtc: s3c: Extract read/write IO into separate functions
  rtc: s3c: Remove usage of devm_rtc_device_register()
  rtc: tps80031: Remove driver
  rtc: sun6i: Allow probing without an early clock provider
  rtc: pcf8523: add BSM support
  ...

Pull more libata updates from Damien Le Moal:
 "Second round of updates for libata for 5.16:

   - Fix READ LOG EXT and READ LOG DMA EXT command timeouts during disk
     revalidation after a resume or a modprobe of the LLDD (me)

   - Remove unnecessary error message in sata_highbank driver (Xu)

   - Better handling of accesses to the IDENTIFY DEVICE data log for
     drives that do not support this log page (me)

   - Fix ahci_shost_attr_group declaration in ahci driver (me)"

* tag 'libata-5.16-rc1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  libata: libahci: declare ahci_shost_attr_group as static
  libata: add horkage for missing Identify Device log
  ata: sata_highbank: Remove unnecessary print function dev_err()
  libata: fix read log timeout value

TL;DR: While a tool like liblockdep is useful, it probably doesn't
belong within the kernel tree.

liblockdep attempts to reuse kernel code both directly (by directly
building the kernel's lockdep code) as well as indirectly (by using
sanitized headers). This makes liblockdep an integral part of the
kernel.

It also makes liblockdep quite unique: while other userspace code might
use sanitized headers, it generally doesn't attempt to use kernel code
directly which means that changes on the kernel side of things don't
affect (and break) it directly.

All our workflows and tooling around liblockdep don't support this
uniqueness. Changes that go into the kernel code aren't validated to not
break in-tree userspace code.

liblockdep ended up being very fragile, breaking over and over, to the
point that living in the same tree as the lockdep code lost most of it's
value.

liblockdep should continue living in an external tree, syncing with
the kernel often, in a controllable way.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit aeb58c86 ("thermal/drivers/int340x: processor_thermal: Suppot
64 bit RFIM responses") started using 'readq()' to read 64-bit status
responses from the int340x hardware.

That's all fine and good, but on 32-bit targets a 64-bit 'readq()' is
ambiguous, since it's no longer an atomic access.  Some hardware might
require 64-bit accesses, and other hardware might want low word first or
high word first.

It's quite likely that the driver isn't relevant in a 32-bit environment
any more, and there's a patch floating around to just make it depend on
X86_64, but let's make it buildable on x86-32 anyway.

The driver previously just read the low 32 bits, so the hardware
certainly is ok with 32-bit reads, and in a little-endian environment
the low word first model is the natural one.

So just add the include for the 'io-64-nonatomic-lo-hi.h' version.

Fixes: aeb58c86 ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prepare input updates for 5.16 merge window.

 * dma-buf: name_lock fixes
 * prime: Keep object ref during mmap
 * nouveau: Fix a refcount issue; Fix device removal; Protect client
   list with dedicated mutex; Fix address CE0 address calculation
 * ttm: Fix race condition during BO eviction
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YYzY6jeox9EeI15i@linux-uq9g.fritz.box

I got a drm-fixes which had some 5.15 stuff in it, so to avoid
the mess just backmerge here.

Linux 5.15
Signed-off-by: Dave Airlie <airlied@redhat.com>

Pull PCI fixes from Bjorn Helgaas:
 "Revert conversion to struct device.driver instead of struct
  pci_dev.driver.

  The device.driver is set earlier, and using it caused the PCI core to
  call driver PM entry points before .probe() and after .remove(), when
  the driver isn't prepared.

  This caused NULL pointer dereferences in i2c_designware_pci and
  probably other driver issues"

* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
  Revert "PCI: Remove struct pci_dev->driver"

ahci_shost_attr_group is referenced only in drivers/ata/libahci.c.
Declare it as static.

Fixes: c3f69c7f ("scsi: ata: Switch to attribute groups")
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

ACS-3 introduced the ATA Identify Device Data log as mandatory. A
warning message currently signals to the user if a device does not
report supporting this log page in the log directory page, regardless
of the ATA version of the device. Furthermore, this warning will appear
for all attempts at accessing this missing log page during device
revalidation.

Since it is useless to constantly access the log directory and warn
about this lack of support once we have discovered that the device
does not support this log page, introduce the horkage flag
ATA_HORKAGE_NO_ID_DEV_LOG to mark a device as lacking support for
the Identify Device Data log page. Set this flag when
ata_log_supported() returns false in ata_identify_page_supported().
The warning is printed only if the device ATA level is 10 or above
(ACS-3 or above), and only once on device scan. With this flag set, the
log directory page is not accessed again to test for Identify Device
Data log page support.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull KCSAN updates from Paul McKenney:
 "This contains initialization fixups, testing improvements, addition of
  instruction pointer to data-race reports, and scoped data-race checks"

* tag 'kcsan.2021.11.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  kcsan: selftest: Cleanup and add missing __init
  kcsan: Move ctx to start of argument list
  kcsan: Support reporting scoped read-write access type
  kcsan: Start stack trace with explicit location if provided
  kcsan: Save instruction pointer for scoped accesses
  kcsan: Add ability to pass instruction pointer of access to reporting
  kcsan: test: Fix flaky test case
  kcsan: test: Use kunit_skip() to skip tests
  kcsan: test: Defer kcsan_test_init() after kunit initialization

Merge tag 'apparmor-pr-2021-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "Features
   - use per file locks for transactional queries
   - update policy management capability checks to work with LSM stacking

  Bug Fixes:
   - check/put label on apparmor_sk_clone_security()
   - fix error check on update of label hname
   - fix introspection of of task mode for unconfined tasks

  Cleanups:
   - avoid -Wempty-body warning
   - remove duplicated 'Returns:' comments
   - fix doc warning
   - remove unneeded one-line hook wrappers
   - use struct_size() helper in kzalloc()
   - fix zero-length compiler warning in AA_BUG()
   - file.h: delete duplicated word
   - delete repeated words in comments
   - remove repeated declaration"

* tag 'apparmor-pr-2021-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: remove duplicated 'Returns:' comments
  apparmor: remove unneeded one-line hook wrappers
  apparmor: Use struct_size() helper in kzalloc()
  apparmor: fix zero-length compiler warning in AA_BUG()
  apparmor: use per file locks for transactional queries
  apparmor: fix doc warning
  apparmor: Remove the repeated declaration
  apparmor: avoid -Wempty-body warning
  apparmor: Fix internal policy capable check for policy management
  apparmor: fix error check
  security: apparmor: delete repeated words in comments
  security: apparmor: file.h: delete duplicated word
  apparmor: switch to apparmor to internal capable check for policy management
  apparmor: update policy capable checks to use a label
  apparmor: fix introspection of of task mode for unconfined tasks
  apparmor: check/put label on apparmor_sk_clone_security()

Merge more updates from Andrew Morton:
 "The post-linux-next material.

  7 patches.

  Subsystems affected by this patch series (all mm): debug,
  slab-generic, migration, memcg, and kasan"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  kasan: add kasan mode messages when kasan init
  mm: unexport {,un}lock_page_memcg
  mm: unexport folio_memcg_{,un}lock
  mm/migrate.c: remove MIGRATE_PFN_LOCKED
  mm: migrate: simplify the file-backed pages validation when migrating its mapping
  mm: allow only SLUB on PREEMPT_RT
  mm/page_owner.c: modify the type of argument "order" in some functions

Pull m68knommu updates from Greg Ungerer:
 "Only two changes.

  One removes the now unused CONFIG_MCPU32 symbol. The other sets a
  default for the CONFIG_MEMORY_RESERVE config symbol (this aids
  scripting and other automation) so you don't interactively get asked
  for a value at configure time.

  Summary:

   - remove unused CONFIG_MCPU32 symbol

   - default CONFIG_MEMORY_RESERVE value (for scripting)"

* tag 'm68knommu-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: Remove MCPU32 config symbol
  m68k: set a default value for MEMORY_RESERVE

This reverts commit 2a4d9408.

Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method.  i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().

Prior to 2a4d9408 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.

2a4d9408 and b5f9c644 ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.

Fixes: 2a4d9408 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

This reverts commit b5f9c644.

Revert b5f9c644 ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").

2a4d9408 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.

Fixes: 2a4d9408 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull tracing fixes from Steven Rostedt:
 "Two locking fixes:

   - Add mutex protection to ring_buffer_reset()

   - Fix deadlock in modify_ftrace_direct_multi()"

* tag 'trace-v5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/direct: Fix lockup in modify_ftrace_direct_multi
  ring-buffer: Protect ring_buffer_reset() from reentrancy

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, can and netfilter.

  Current release - regressions:

   - bpf: do not reject when the stack read size is different from the
     tracked scalar size

   - net: fix premature exit from NAPI state polling in napi_disable()

   - riscv, bpf: fix RV32 broken build, and silence RV64 warning

  Current release - new code bugs:

   - net: fix possible NULL deref in sock_reserve_memory

   - amt: fix error return code in amt_init(); fix stopping the
     workqueue

   - ax88796c: use the correct ioctl callback

  Previous releases - always broken:

   - bpf: stop caching subprog index in the bpf_pseudo_func insn

   - security: fixups for the security hooks in sctp

   - nfc: add necessary privilege flags in netlink layer, limit
     operations to admin only

   - vsock: prevent unnecessary refcnt inc for non-blocking connect

   - net/smc: fix sk_refcnt underflow on link down and fallback

   - nfnetlink_queue: fix OOB when mac header was cleared

   - can: j1939: ignore invalid messages per standard

   - bpf, sockmap:
      - fix race in ingress receive verdict with redirect to self
      - fix incorrect sk_skb data_end access when src_reg = dst_reg
      - strparser, and tls are reusing qdisc_skb_cb and colliding

   - ethtool: fix ethtool msg len calculation for pause stats

   - vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
     access an unregistering real_dev

   - udp6: make encap_rcv() bump the v6 not v4 stats

   - drv: prestera: add explicit padding to fix m68k build

   - drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge

   - drv: mvpp2: fix wrong SerDes reconfiguration order

  Misc & small latecomers:

   - ipvs: auto-load ipvs on genl access

   - mctp: sanity check the struct sockaddr_mctp padding fields

   - libfs: support RENAME_EXCHANGE in simple_rename()

   - avoid double accounting for pure zerocopy skbs"

* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
  selftests/net: udpgso_bench_rx: fix port argument
  net: wwan: iosm: fix compilation warning
  cxgb4: fix eeprom len when diagnostics not implemented
  net: fix premature exit from NAPI state polling in napi_disable()
  net/smc: fix sk_refcnt underflow on linkdown and fallback
  net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
  gve: fix unmatched u64_stats_update_end()
  net: ethernet: lantiq_etop: Fix compilation error
  selftests: forwarding: Fix packet matching in mirroring selftests
  vsock: prevent unnecessary refcnt inc for nonblocking connect
  net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
  net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
  net: stmmac: allow a tc-taprio base-time of zero
  selftests: net: test_vxlan_under_vrf: fix HV connectivity test
  net: hns3: allow configure ETS bandwidth of all TCs
  net: hns3: remove check VF uc mac exist when set by PF
  net: hns3: fix some mac statistics is always 0 in device version V2
  net: hns3: fix kernel crash when unload VF while it is being reset
  net: hns3: sync rx ring head in echo common pull
  net: hns3: fix pfc packet number incorrect after querying pfc parameters
  ...

Pull char/misc fix from Greg KH:
 "Here is a single fix for 5.16-rc1 to resolve a build problem that came
  in through the coresight tree (and as such came in through the
  char/misc tree merge in the 5.16-rc1 merge window).

  It resolves a build problem with 'allmodconfig' on arm64 and is acked
  by the proper subsystem maintainers. It has been in linux-next all
  week with no reported problems"

* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  arm64: cpufeature: Export this_cpu_has_cap helper