Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-12-05 (i40e)

Michal clears XPS init flag on reset to allow for updated values to be
written.

Sylwester adds sleep to VF reset to resolve issue of VFs not getting
resources.

Przemyslaw rejects filters for raw IPv4 or IPv6 l4_4_bytes filters as they
 are not supported.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  i40e: Disallow ip4 and ip6 l4_4_bytes
  i40e: Fix for VF MAC address 0
  i40e: Fix not setting default xps_cpus after reset
====================

Link: https://lore.kernel.org/r/20221205212523.3197565-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When dsa_devlink_region_create failed in sja1105_setup_devlink_regions(),
priv->regions is not released.

Fixes: bf425b82 ("net: dsa: sja1105: expose static config as devlink region")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205012132.2110979-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ido Schimmel says:

====================
ipv4: Two small fixes for bugs in IPv4 routing code.

A variation of the second bug was reported by an FRR 5.0 (released
06/18) user as this version was setting a table ID of 0 for the
default VRF, unlike iproute2 and newer FRR versions.

The first bug was discovered while fixing the second.

Both bugs are not regressions (never worked) and are not critical
in my opinion, so the fixes can be applied to net-next, if desired.

No regressions in other tests:

 # ./fib_tests.sh
 ...
 Tests passed: 191
 Tests failed:   0
====================

Link: https://lore.kernel.org/r/20221204075045.3780097-1-idosch@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cited commit added the table ID to the FIB info structure, but did not
properly initialize it when table ID 0 is used. This can lead to a route
in the default VRF with a preferred source address not being flushed
when the address is deleted.

Consider the following example:

 # ip address add dev dummy1 192.0.2.1/28
 # ip address add dev dummy1 192.0.2.17/28
 # ip route add 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 100
 # ip route add table 0 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 200
 # ip route show 198.51.100.0/24
 198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 100
 198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200

Both routes are installed in the default VRF, but they are using two
different FIB info structures. One with a metric of 100 and table ID of
254 (main) and one with a metric of 200 and table ID of 0. Therefore,
when the preferred source address is deleted from the default VRF,
the second route is not flushed:

 # ip address del dev dummy1 192.0.2.17/28
 # ip route show 198.51.100.0/24
 198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200

Fix by storing a table ID of 254 instead of 0 in the route configuration
structure.

Add a test case that fails before the fix:

 # ./fib_tests.sh -t ipv4_del_addr

 IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Table ID 0
     TEST: Route removed in default VRF when source address deleted      [FAIL]

 Tests passed:   8
 Tests failed:   1

And passes after:

 # ./fib_tests.sh -t ipv4_del_addr

 IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Table ID 0
     TEST: Route removed in default VRF when source address deleted      [ OK ]

 Tests passed:   9
 Tests failed:   0

Fixes: 5a56a0b3 ("net: Don't delete routes in different VRFs")
Reported-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Cited commit added the table ID to the FIB info structure, but did not
prevent structures with different table IDs from being consolidated.
This can lead to routes being flushed from a VRF when an address is
deleted from a different VRF.

Fix by taking the table ID into account when looking for a matching FIB
info. This is already done for FIB info structures backed by a nexthop
object in fib_find_info_nh().

Add test cases that fail before the fix:

 # ./fib_tests.sh -t ipv4_del_addr

 IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [FAIL]
     TEST: Route in default VRF not removed                              [ OK ]
 RTNETLINK answers: File exists
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [FAIL]

 Tests passed:   6
 Tests failed:   2

And pass after:

 # ./fib_tests.sh -t ipv4_del_addr

 IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]

 Tests passed:   8
 Tests failed:   0

Fixes: 5a56a0b3 ("net: Don't delete routes in different VRFs")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Prior to the Fixes: commit, the initialization code went through the
same fec_enet_set_coalesce() function as used by ethtool, and that
function correctly checks whether the current variant has support for
irq coalescing.

Now that the initialization code instead calls fec_enet_itr_coal_set()
directly, that call needs to be guarded by a check for the
FEC_QUIRK_HAS_COALESCE bit.

Fixes: df727d45 (net: fec: don't reset irq coalesce settings to defaults on "ip link up")
Reported-by: Greg Ungerer <gregungerer@westnet.com.au>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205204604.869853-1-linux@rasmusvillemoes.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In commit 4d633d1b ("bonding: fix ICMPv6 header handling when receiving
IPv6 messages"), there is a copy/paste issue for NA daddr. I found that
in my testing and fixed it in my local branch. But I forgot to re-format
the patch and sent the wrong mail.

Fix it by reading the correct dest address.

Fixes: 4d633d1b ("bonding: fix ICMPv6 header handling when receiving IPv6 messages")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20221206032055.7517-1-liuhangbin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the potential risk of OOB if skb_linearize() fails in
tipc_link_proto_rcv().

Fixes: 5cbb28a4 ("tipc: linearize arriving NAME_DISTR and LINK_PROTO buffers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20221203094635.29024-1-yuehaibing@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The skb is delivered to napi_gro_receive() which may free it, after
calling this, dereferencing skb may trigger use-after-free.

Fixes: 57c5bc9a ("net: hisilicon: add hix5hd2 mac driver")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221203094240.1240211-2-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

There is warning report about of_node refcount leak
while probing mdio device:

OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@710700c0/ethernet@4

In of_mdiobus_register_device(), we increase fwnode refcount
by fwnode_handle_get() before associating the of_node with
mdio device, but it has never been decreased in normal path.
Since that, in mdio_device_release(), it needs to call
fwnode_handle_put() in addition instead of calling kfree()
directly.

After above, just calling mdio_device_free() in the error handle
path of of_mdiobus_register_device() is enough to keep the
refcount balanced.

Fixes: a9049e0c ("mdio: Add support for mdio drivers.")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221203073441.3885317-1-zengheng4@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The skb is delivered to napi_gro_receive() which may free it, after
calling this, dereferencing skb may trigger use-after-free.

Fixes: 542ae60a ("net: hisilicon: Add Fast Ethernet MAC driver")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221203094240.1240211-1-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The nicvf_probe() won't destroy workqueue when register_netdev()
failed. Add destroy_workqueue err handle case to fix this issue.

Fixes: 2ecbe4f4 ("net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.")
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20221203094125.602812-1-liuyongqiang13@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The skb is delivered to napi_gro_receive() which may free it, after calling this,
dereferencing skb may trigger use-after-free.

Fixes: 1c59eb67 ("ravb: Fillup ravb_rx_gbeth() stub")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221203092941.10880-1-yuehaibing@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The mchp_sparx5_probe() won't destroy workqueue created by
create_singlethread_workqueue() in sparx5_start() when later
inits failed. Add destroy_workqueue in the cleanup_ports case,
also add it in mchp_sparx5_remove()

Fixes: b37a1bae ("net: sparx5: add mactable support")
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Link: https://lore.kernel.org/r/20221203070259.19560-1-linqiheng@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Although the type I ERSPAN is based on the barebones IP + GRE
encapsulation and no extra ERSPAN header. Report erspan version on GRE
interface looks unreasonable. Fix this by separating the erspan and gre
fill info.

IPv6 GRE does not have this info as IPv6 only supports erspan version
1 and 2.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: f989d546 ("erspan: Add type I version 0 support.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Link: https://lore.kernel.org/r/20221203032858.3130339-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When failed to alloc ipc_mux->ul_adb.pp_qlt in ipc_mux_init(), ipc_mux
is not released.

Fixes: 1f52d7b6 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Link: https://lore.kernel.org/r/20221203020903.383235-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

After calling napi_complete_done(), the NAPIF_STATE_SCHED bit may be
cleared, and another CPU can start napi thread and access per-CQ variable,
cq->work_done. If the other thread (for example, from busy_poll) sets
it to a value >= budget, this thread will continue to run when it should
stop, and cause memory corruption and panic.

To fix this issue, save the per-CQ work_done variable in a local variable
before napi_complete_done(), so it won't be corrupted by a possible
concurrent thread after napi_complete_done().

Also, add a flag bit to advertise to the NIC firmware: the NAPI work_done
variable race is fixed, so the driver is able to reliably support features
like busy_poll.

Cc: stable@vger.kernel.org
Fixes: e1b5683f ("net: mana: Move NAPI from EQ to CQ")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1670010190-28595-1-git-send-email-haiyangz@microsoft.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.

Fixes: afea0365 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

While running under CONFIG_FORTIFY_SOURCE=y, syzkaller reported:

  memcpy: detected field-spanning write (size 129) of single field "target->sensf_res" at net/nfc/nci/ntf.c:260 (size 18)

This appears to be a legitimate lack of bounds checking in
nci_add_new_protocol(). Add the missing checks.

Reported-by: syzbot+210e196cef4711b65139@syzkaller.appspotmail.com
Link: https://lore.kernel.org/lkml/0000000000001c590f05ee7b3ff4@google.com
Fixes: 019c4fba ("NFC: Add NCI multiple targets support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221202214410.never.693-kees@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return -EOPNOTSUPP, when user requests l4_4_bytes for raw IP4 or
IP6 flow director filters. Flow director does not support filtering
on l4 bytes for PCTYPEs used by IP4 and IP6 filters.
Without this patch, user could create filters with l4_4_bytes fields,
which did not do any filtering on L4, but only on L3 fields.

Fixes: 36777d9f ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Kamil Maziarz  <kamil.maziarz@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

After spawning max VFs on a PF, some VFs were not getting resources and
their MAC addresses were 0. This was caused by PF sleeping before flushing
HW registers which caused VIRTCHNL_VFR_VFACTIVE to not be set in time for
VF.

Fix by adding a sleep after hw flush.

Fixes: e4b433f4 ("i40e: reset all VFs in parallel when rebuilding PF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

During tx rings configuration default XPS queue config is set and
__I40E_TX_XPS_INIT_DONE is locked. __I40E_TX_XPS_INIT_DONE state is
cleared and set again with default mapping only during queues build,
it means after first setup or reset with queues rebuild. (i.e.
ethtool -L <interface> combined <number>) After other resets (i.e.
ethtool -t <interface>) XPS_INIT_DONE is not cleared and those default
maps cannot be set again. It results in cleared xps_cpus mapping
until queues are not rebuild or mapping is not set by user.

Add clearing __I40E_TX_XPS_INIT_DONE state during reset to let
the driver set xps_cpus to defaults again after it was cleared.

Fixes: 6f853d4f ("i40e: allow XPS with QoS enabled")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The pp->indir[0] value comes from the user.  It is passed to:

	if (cpu_online(pp->rxq_def))

inside the mvneta_percpu_elect() function.  It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.

Fixes: cad5d847 ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A NAPI is setup for each network sring to poll data to kernel
The sring with source host is destroyed before live migration and
new sring with target host is setup after live migration.
The NAPI for the old sring is not deleted until setup new sring
with target host after migration. With busy_poll/busy_read enabled,
the NAPI can be polled before got deleted when resume VM.

BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: xennet_poll+0xae/0xd20
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
Call Trace:
 finish_task_switch+0x71/0x230
 timerqueue_del+0x1d/0x40
 hrtimer_try_to_cancel+0xb5/0x110
 xennet_alloc_rx_buffers+0x2a0/0x2a0
 napi_busy_loop+0xdb/0x270
 sock_poll+0x87/0x90
 do_sys_poll+0x26f/0x580
 tracing_map_insert+0x1d4/0x2f0
 event_hist_trigger+0x14a/0x260

 finish_task_switch+0x71/0x230
 __schedule+0x256/0x890
 recalc_sigpending+0x1b/0x50
 xen_sched_clock+0x15/0x20
 __rb_reserve_next+0x12d/0x140
 ring_buffer_lock_reserve+0x123/0x3d0
 event_triggers_call+0x87/0xb0
 trace_event_buffer_commit+0x1c4/0x210
 xen_clocksource_get_cycles+0x15/0x20
 ktime_get_ts64+0x51/0xf0
 SyS_ppoll+0x160/0x1a0
 SyS_ppoll+0x160/0x1a0
 do_syscall_64+0x73/0x130
 entry_SYSCALL_64_after_hwframe+0x41/0xa6
...
RIP: xennet_poll+0xae/0xd20 RSP: ffffb4f041933900
CR2: 0000000000000008
---[ end trace f8601785b354351c ]---

xen frontend should remove the NAPIs for the old srings before live
migration as the bond srings are destroyed

There is a tiny window between the srings are set to NULL and
the NAPIs are disabled, It is safe as the NAPI threads are still
frozen at that time
Signed-off-by: Lin Liu <lin.liu@citrix.com>
Fixes: 4ec24119 ([NET]: Do not check netif_running() and carrier state in ->poll())
Signed-off-by: David S. Miller <davem@davemloft.net>

consume_skb on transmitted, kfree_skb on dropped, do not free on
TX_BUSY.

Previously the xmit function could return -EBUSY without freeing, which
supposedly is interpreted as a drop. And was using kfree on successfully
transmitted packets.

sparx5_fdma_xmit and sparx5_inject returns error code, where -EBUSY
indicates TX_BUSY and any other error code indicates dropped.

Fixes: f3cad261 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In otx2_init_tc(), if rhashtable_init() failed, it does not free
tc->tc_entries_bitmap which is allocated in otx2_tc_alloc_ent_bitmap().

Fixes: 2e2a8126 ("octeontx2-pf: Unify flow management variables")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If phy_device_register() or fwnode_mdiobus_phy_device_register()
fail, phy_device_free() is called, the device refcount is decreased
to 0, then fwnode_handle_put() will be called in phy_device_release(),
but in the error path, fwnode_handle_put() has already been called,
so set fwnode to NULL after fwnode_handle_put() in the error path to
avoid double put.

Fixes: cdde1560 ("net: mdiobus: fix unbalanced node reference count")
Reported-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A loop for reading MISTAT register continues while regmap_read() fails
and (mistat & BUSY), but if regmap_read() fails a value of mistat is
undefined.

The patch proposes to check for BUSY flag only when regmap_read()
succeed. Compile test only.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d70e5326 ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d70e5326 ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there's only one buffer to dma and its length is 4096, then
only one data descriptor is needed to carry it according to current
descriptor definition. So the descriptor type should be `simple`
instead of `gather`, the latter requires more than one descriptor,
otherwise it'll be dropped by application firmware.

Fixes: c10d12e3 ("nfp: add support for NFDK data path")
Fixes: d9d95049 ("nfp: nfdk: implement xdp tx path for NFDK")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Richard Donkin <richard.donkin@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221202134646.311108-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The latest version of grep claims the egrep is now obsolete so the build
now contains warnings that look like:
	egrep: warning: egrep is obsolescent; using grep -E
fix this using "grep -E" instead.

  sed -i "s/egrep/grep -E/g" `grep egrep -rwl tools/testing/selftests/net`

Here are the steps to install the latest grep:

  wget http://ftp.gnu.org/gnu/grep/grep-3.8.tar.gz
  tar xf grep-3.8.tar.gz
  cd grep-3.8 && ./configure && make
  sudo make install
  export PATH=/usr/local/bin:$PATH
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1669864248-829-1-git-send-email-yangtiezhu@loongson.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When testing in kci_test_ipsec_offload, srcip is configured as $dstip,
it should add xfrm policy rule in instead of out.
The test result of this patch is as follows:
PASS: ipsec_offload

Fixes: 2766a111 ("selftests: rtnetlink: add ipsec offload API test")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20221201082246.14131-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit d2825fa9 ("crypto: sm3,sm4 - move into crypto directory") moves
SM3 and SM4 algorithm implementations from stand-alone library to crypto
API. The corresponding configuration options for the API version (generic)
are CONFIG_CRYPTO_SM3_GENERIC and CONFIG_CRYPTO_SM4_GENERIC, respectively.

Replace option selected in selftests configuration from the library version
to the API version.

Fixes: d2825fa9 ("crypto: sm3,sm4 - move into crypto directory")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221201131852.38501-1-tianjia.zhang@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return NULL if we got unexpected value from skb_trim_rcsum() in
sja1110_rcv_inband_control_extension()

Fixes: 4913b8eb ("net: dsa: add support for the SJA1110 native tagging protocol")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221201140032.26746-3-artem.chernyshev@red-soft.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return NULL if we got unexpected value from skb_trim_rcsum()
in hellcreek_rcv()

Fixes: 01ef09ca ("net: dsa: Add tag handling for Hirschmann Hellcreek switches")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20221201140032.26746-2-artem.chernyshev@red-soft.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return NULL if we got unexpected value from skb_trim_rcsum()
in ksz_common_rcv()

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: bafe9ba7 ("net: dsa: ksz: Factor out common tag code")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221201140032.26746-1-artem.chernyshev@red-soft.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - Fix regressions with CSR controller clones
 - Fix support for Read Local Supported Codecs V2
 - Fix overflow on L2CAP code
 - Fix missing hci_dev_put on ISO and L2CAP code

* tag 'for-net-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: Fix crash when replugging CSR fake controllers
  Bluetooth: Fix not cleanup led when bt_init fails
  Bluetooth: Fix support for Read Local Supported Codecs V2
  Bluetooth: Remove codec id field in vendor codec definition
  Bluetooth: L2CAP: Fix u8 overflow
  Bluetooth: silence a dmesg error message in hci_request.c
  Bluetooth: hci_conn: add missing hci_dev_put() in iso_listen_bis()
  Bluetooth: 6LoWPAN: add missing hci_dev_put() in get_l2cap_conn()
  Bluetooth: btusb: Add debug message for CSR controllers
  Bluetooth: btusb: Fix CSR clones again by re-adding ERR_DATA_REPORTING quirk
====================

Link: https://lore.kernel.org/r/20221202213726.2801581-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It seems fake CSR 5.0 clones can cause the suspend notifier to be
registered twice causing the following kernel panic:

[   71.986122] Call Trace:
[   71.986124]  <TASK>
[   71.986125]  blocking_notifier_chain_register+0x33/0x60
[   71.986130]  hci_register_dev+0x316/0x3d0 [bluetooth 99b5497ea3d09708fa1366c1dc03288bf3cca8da]
[   71.986154]  btusb_probe+0x979/0xd85 [btusb e1e0605a4f4c01984a4b9c8ac58c3666ae287477]
[   71.986159]  ? __pm_runtime_set_status+0x1a9/0x300
[   71.986162]  ? ktime_get_mono_fast_ns+0x3e/0x90
[   71.986167]  usb_probe_interface+0xe3/0x2b0
[   71.986171]  really_probe+0xdb/0x380
[   71.986174]  ? pm_runtime_barrier+0x54/0x90
[   71.986177]  __driver_probe_device+0x78/0x170
[   71.986180]  driver_probe_device+0x1f/0x90
[   71.986183]  __device_attach_driver+0x89/0x110
[   71.986186]  ? driver_allows_async_probing+0x70/0x70
[   71.986189]  bus_for_each_drv+0x8c/0xe0
[   71.986192]  __device_attach+0xb2/0x1e0
[   71.986195]  bus_probe_device+0x92/0xb0
[   71.986198]  device_add+0x422/0x9a0
[   71.986201]  ? sysfs_merge_group+0xd4/0x110
[   71.986205]  usb_set_configuration+0x57a/0x820
[   71.986208]  usb_generic_driver_probe+0x4f/0x70
[   71.986211]  usb_probe_device+0x3a/0x110
[   71.986213]  really_probe+0xdb/0x380
[   71.986216]  ? pm_runtime_barrier+0x54/0x90
[   71.986219]  __driver_probe_device+0x78/0x170
[   71.986221]  driver_probe_device+0x1f/0x90
[   71.986224]  __device_attach_driver+0x89/0x110
[   71.986227]  ? driver_allows_async_probing+0x70/0x70
[   71.986230]  bus_for_each_drv+0x8c/0xe0
[   71.986232]  __device_attach+0xb2/0x1e0
[   71.986235]  bus_probe_device+0x92/0xb0
[   71.986237]  device_add+0x422/0x9a0
[   71.986239]  ? _dev_info+0x7d/0x98
[   71.986242]  ? blake2s_update+0x4c/0xc0
[   71.986246]  usb_new_device.cold+0x148/0x36d
[   71.986250]  hub_event+0xa8a/0x1910
[   71.986255]  process_one_work+0x1c4/0x380
[   71.986259]  worker_thread+0x51/0x390
[   71.986262]  ? rescuer_thread+0x3b0/0x3b0
[   71.986264]  kthread+0xdb/0x110
[   71.986266]  ? kthread_complete_and_exit+0x20/0x20
[   71.986268]  ret_from_fork+0x1f/0x30
[   71.986273]  </TASK>
[   71.986274] ---[ end trace 0000000000000000 ]---
[   71.986284] btusb: probe of 2-1.6:1.0 failed with error -17

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216683
Cc: stable@vger.kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Leonardo Eugênio <lelgenio@disroot.org>

bt_init() calls bt_leds_init() to register led, but if it fails later,
bt_leds_cleanup() is not called to unregister it.

This can cause panic if the argument "bluetooth-power" in text is freed
and then another led_trigger_register() tries to access it:

BUG: unable to handle page fault for address: ffffffffc06d3bc0
RIP: 0010:strcmp+0xc/0x30
  Call Trace:
    <TASK>
    led_trigger_register+0x10d/0x4f0
    led_trigger_register_simple+0x7d/0x100
    bt_init+0x39/0xf7 [bluetooth]
    do_one_initcall+0xd0/0x4e0

Fixes: e64c97b5 ("Bluetooth: Add combined LED trigger for controller power")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Handling of Read Local Supported Codecs was broken during the
HCI serialization design change patches.

Fixes: d0b13706 ("Bluetooth: hci_sync: Rework init stages")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>