slot_dequeue_head() should make sure slot skb chain is correct in both
ways, or we can crash if all possible flows are in use.

Jarek pointed out slot_queue_init() can now be done in sfq_init() once,
instead each time a flow is setup.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFQ is currently 'limited' to small packets, because it uses a 15bit
allotment number per flow. Introduce a scale by 8, so that we can handle
full size TSO/GRO packets.

Use appropriate handling to make sure allot is positive before a new
packet is dequeued, so that fairness is respected.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sky2 driver uses the legacy PCI power management, so it has to do
some PCI-specific things in its ->suspend() and ->resume() callbacks,
which isn't necessary and should better be done by the PCI
sybsystem-level power management code.  Moreover, it uses
device_set_wakeup_enable() incorrectly (that function should be
used when the WoL setting is changed rather than during suspend).

Convert sky2 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.

Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tg3 driver uses the legacy PCI power management, so it has to do
some PCI-specific things in its ->suspend() and ->resume() callbacks,
which isn't necessary and should better be done by the PCI
sybsystem-level power management code.

Convert tg3 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.

Tested on HP nx6325 with a NetXtreme BCM5788 adapter.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already verified that "dev->udev->actconfig->extralen" was non-zero
so "len" is non-zero here as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update MIPS firmware to 6.2.1, with improved small packet performance
in RSS mode, and iSCSI CID allocation bug fix on 5708.

Update driver version to 2.0.21.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing ring size, we free all memory including status block
memory.  If we're in INTA mode and sharing IRQ, the IRQ handler can
be called and it will reference the NULL status block pointer.

Because of the lockless design of the IRQ handler, there is no simple
way to synchronize and prevent this.  So we avoid this problem by
freeing the IRQ handler before freeing the status block memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver supports only Intelligent Ethernet Adapters.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A couple of small cleanups for patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding dcbnl implementation to bnx2x allowing users to manage the
embedded DCBX engine.

This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a pair of set-get routines to dcbnl for setting the negotiation
flags of the various DCB features. Conforms to the CEE flavor of DCBX
The user sets these flags (enable, advertise, willing) for each feature
to be used by the DCBX engine. The 'get' routine returns which of the
features is enabled after the negotiation.

This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding an optional DCBX capability and a pair for get-set routines for
setting the device DCBX mode. The DCBX capability is a bit field of
supported attributes. The user is expected to set the DCBX mode with a
subset of the advertised attributes.

This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DCBx applications priorities can be changed dynamically. If
application stacks are expected to keep the skb priority
consistent with the dcbx priority the stack will need to
be notified when these changes occur.

This patch adds application notifiers for the stack to register
with.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds application tlv handlers. Networking stacks
may use the application priority to set the skb priority of
their stack using the negoatiated dcbx priority.

This patch provides the dcb_{get|set}app() routines for the
stack to query these parameters. Notice lower layer drivers
can use the dcbnl_ops routines if additional handling is
needed. Perhaps in the firmware case for example
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IEEE8021Qaz is the IEEE standard version of CEE. The
standard has had enough significant changes from the CEE
version that many of the CEE attributes have no meaning
in the new spec or do not easily map to IEEE standards.

Rather then attempt to create a complicated mapping
between CEE and IEEE standards this patch adds a nested
IEEE attribute to the list of DCB attributes. The policy
is,

	[DCB_ATTR_IFNAME]
	[DCB_ATTR_STATE]
	...
	[DCB_ATTR_IEEE]
		[DCB_ATTR_IEEE_ETS]
		[DCB_ATTR_IEEE_PFC]
		[DCB_ATTR_IEEE_APP_TABLE]
			[DCB_ATTR_IEEE_APP]
			...

The following dcbnl_rtnl_ops routines were added to handle
the IEEE standard,

	int (*ieee_getets) (struct net_device *, struct ieee_ets *);
	int (*ieee_setets) (struct net_device *, struct ieee_ets *);
	int (*ieee_getpfc) (struct net_device *, struct ieee_pfc *);
	int (*ieee_setpfc) (struct net_device *, struct ieee_pfc *);
	int (*ieee_getapp) (struct net_device *, struct dcb_app *);
	int (*ieee_setapp) (struct net_device *, struct dcb_app *);
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is just a cleanup to make the static checkers happy.  We don't need
to check "own" twice.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv4/fib_frontend.c

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  ipv4: dont create routes on down devices
  epic100: hamachi: yellowfin: Fix skb allocation size
  sundance: Fix oopses with corrupted skb_shared_info
  Revert "ipv4: Allow configuring subnets as local addresses"
  USB: mcs7830: return negative if auto negotiate fails
  irda: prevent integer underflow in IRLMP_ENUMDEVICES
  tcp: fix listening_get_next()
  atl1c: Do not use legacy PCI power management
  mac80211: fix mesh forwarding
  MAINTAINERS: email address change
  net: Fix range checks in tcf_valid_offset().
  net_sched: sch_sfq: fix allot handling
  hostap: remove netif_stop_queue from init
  mac80211/rt2x00: add ieee80211_tx_status_ni()
  typhoon: memory corruption in typhoon_get_drvinfo()
  net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
  net_sched: always clone skbs
  ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
  netlink: fix gcc -Wconversion compilation warning
  asix: add USB ID for Logitec LAN-GTJ U2A
  ...

In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.

# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
  kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3

After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.

Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Made IOC auto_recovery synchronized and not timer based.
	- Only one PCI function will attempt to recover and reinitialize
	the ASIC on a failure, that too after all the active PCI
	functions acknowledge the IOC failure.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Retrieve the VLAN configuration from the networking stack
	and apply it to the base interface during ifconfig up
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Remove unused APIs and code cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Added a check in ioc firmware lock function to see if IOC is
	in BFI_IOC_UNINIT state or not. If it is not in UNINIT state
	and the last IOC boot was not done by OS driver, force IOC state
	to BFI_IOC_UNINIT
	- Unused macro and API cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Call netif_wake_queue() if we have freed up sufficient elements
	at the end of completion processing
	- Add netif_queue_stopped counter back to bnad_drv_stats {}
	- Get netif_queue_stopped value from stack
	- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Enable reception of pure priority tagged packets by default by
	turning on VLAN Id = 0
	- Clear the promiscuous mode, all multicast mode flags when
	bna_rxf_uninit is called
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Removed semaphore register dump from ethtool
	- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Fixed port enable/disable sync through a change in LL port state
	machine
	- Change txq->priority masking to 0x7 (3 bits) from 0x3 (2 bits)
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Check HW ready condition before accessing h/w register in data-path
	- Postpone clean-up of data buffers to the data-path restart path and
	wait in the cleanup routines for in-flight DMA to complete
	- Separate out Tx completion processing from Rx poll routine
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The X540 introduces a new Virtual Function device ID so that the X540
VF device can be distinguished from the 82599 VF device.  The X540 VF
device will have additional capability over the 82599 VF device so it
is necessary to be able to discern the difference.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for the anti-spoofing feature in the HW.  Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and a counter incremented.  During the watchdog timer the spoofed
packet dropped counter is read and if it is non-zero then a warning
message is displayed on the host VMM's console.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add X540 specific feature support to X540
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print warnings to the system log when the VF attempts to override
MAC/VLAN settings that were configured by the VMM Host administrator
using the ip link set commands.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support to igbvf for the new i350 virtual function device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change forces the link down when a mailbox timeout has occurred.
Previously it was possible for a mailbox timeout to occur but for the
interface to stay up.  The problem with this was that it became possible
for an interface to stay up and miss multiple requests resulting in a
possible issue since the interface will be running in an unknown state.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for the anti-spoofing feature in the HW.  Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and an event generated.  When the watchdog task runs it will call a
function to check if any spoof events occurred.  If an event was
detected then a warning message is dumped to the system log.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does the following:

1. Changes the existing supported device id's so now DH89xxCC is not supported when EEPROM is not read.
2. Adds two more device ids for DH89xxCC in backplane mode and SFP.
3. Driver now initializes previously possibly uninitialized value in igb_reset_mdicnfg_82580().
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>