axnet_cs:
    Some Ax88790 chip need to reinitialize the CISREG_CCSR register
    after resume.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.

Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")

The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.

Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

Now with improved comma support.

On parsing malformed X.25 facilities, decrementing the remaining length
may cause it to underflow.  Since the length is an unsigned integer,
this will result in the loop continuing until the kernel crashes.

This patch adds checks to ensure decrementing the remaining length does
not cause it to wrap around.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add call to Firmware to reset its VF State when we first attach to the VF.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fail open if link_start() fails.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a bunch of T4 Device IDs for the VF Driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were some errors in the way that internal Gather Lists were being
translated into skb's.  This also makes the VF Driver look more like the PF
Driver to facilitate easier comarison.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix botch in Generic Receive Offload (the Packet Gather List Total length
field wasn't being initialized).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't implement (struct net_device_ops *)->ndo_select_queue() with simple
call to skb_tx_hash().  This leads to non-persistent TX queue selection in
the Linux dev_pick_tx() routine for TCP connections.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol.  However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol.  This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags.  Instead,
look inside the header if necessary to determine the correct
protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on how a packet is vlan tagged (i.e. hardware accelerated or
not), the encapsulated protocol is stored in different locations.  This
provides a consistent method of accessing that protocol, which is needed
by drivers, security checks, etc.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For device that supports VIRTIO_NET_F_STATUS, there's no need to
assume the link is up and we need to call nerif_carrier_off() before
querying device status, otherwise we may get wrong operstate after
diver was loaded because the link watch event was not fired as
expected.

For device that does not support VIRITO_NET_F_STATUS, we could not get
its status through virtnet_update_status() and what we can only do is
always assuming the link is up.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This script:
 while [ 1==1 ] ; do ifconfig eth0 up; usleep 1950000 ;ifconfig eth0 down; dmesg -c ;done
causes in just a second or two:
INFO: task ifconfig:572 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ifconfig      D 0ff65760     0   572    369 0x00000000
Call Trace:
[c6157be0] [c6008460] 0xc6008460 (unreliable)
[c6157ca0] [c0008608] __switch_to+0x4c/0x6c
[c6157cb0] [c028fecc] schedule+0x184/0x310
[c6157ce0] [c0290e54] __mutex_lock_slowpath+0xa4/0x150
[c6157d20] [c0290c48] mutex_lock+0x44/0x48
[c6157d30] [c01aba74] phy_stop+0x20/0x70
[c6157d40] [c01aef40] ucc_geth_stop+0x30/0x98
[c6157d60] [c01b18fc] ucc_geth_close+0x9c/0xdc
[c6157d80] [c01db0cc] __dev_close+0xa0/0xd0
[c6157d90] [c01deddc] __dev_change_flags+0x8c/0x148
[c6157db0] [c01def54] dev_change_flags+0x1c/0x64
[c6157dd0] [c0237ac8] devinet_ioctl+0x678/0x784
[c6157e50] [c0239a58] inet_ioctl+0xb0/0xbc
[c6157e60] [c01cafa8] sock_ioctl+0x174/0x2a0
[c6157e80] [c009a16c] vfs_ioctl+0xcc/0xe0
[c6157ea0] [c009a998] do_vfs_ioctl+0xc4/0x79c
[c6157f10] [c009b0b0] sys_ioctl+0x40/0x74
[c6157f40] [c00117c4] ret_from_syscall+0x0/0x38

The reason appears to be ucc_geth_stop meets adjust_link as the
PHY reports PHY changes. I belive adjust_link hangs somewhere,
holding the PHY lock, because ucc_geth_stop disabled the
controller HW.
Fix is to stop the PHY before disabling the controller.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:

Don't bring the interface down and up, just reinit controller HW
and PHY.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parameter 'len' is size_t type so it will never get negative.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.

Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.

The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The type of FRAG6_CB(prev)->offset is int, skb->len is *unsigned* int,
and offset is int.

Without this patch, type conversion occurred to this expression, when
(FRAG6_CB(prev)->offset + prev->len) is less than offset.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

The NF_HOOK_COND returns 0 when it shouldn't due to what I believe to be an
error in the code as the order of operations is not what was intended.  C will
evalutate == before =.  Which means ret is getting set to the bool result,
rather than the return value of the function call.  The code says

if (ret = function() == 1)
when it meant to say:
if ((ret = function()) == 1)

Normally the compiler would warn, but it doesn't notice it because its
a actually complex conditional and so the wrong code is wrapped in an explict
set of () [exactly what the compiler wants you to do if this was intentional].
Fixing this means that errors when netfilter denies a packet get propagated
back up the stack rather than lost.

Problem introduced by commit 2249065f (netfilter: get rid of the grossness
in netfilter.h).
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

As noted by Steve Chen, since commit
f5fff5dc ("tcp: advertise MSS
requested by user") we can end up with a situation where
tcp_select_initial_window() does a divide by a zero (or
even negative) mss value.

The problem is that sometimes we effectively subtract
TCPOLEN_TSTAMP_ALIGNED and/or TCPOLEN_MD5SIG_ALIGNED from the mss.

Fix this by increasing the minimum from 8 to 64.
Reported-by: Steve Chen <schen@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]

We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

packet_getname_spkt() doesn't initialize all members of sa_data field of
sockaddr struct if strlen(dev->name) < 13.  This structure is then copied
to userland.  It leads to leaking of contents of kernel stack memory.
We have to fully fill sa_data with strncpy() instead of strlcpy().

The same with packet_getname(): it doesn't initialize sll_pkttype field of
sockaddr_ll.  Set it to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a possibility malicious users can get limited information about
uninitialized stack mem array. Even if sk_run_filter() result is bound
to packet length (0 .. 65535), we could imagine this can be used by
hostile user.

Initializing mem[] array, like Dan Rosenberg suggested in his patch is
expensive since most filters dont even use this array.

Its hard to make the filter validation in sk_chk_filter(), because of
the jumps. This might be done later.

In this patch, I use a bitmap (a single long var) so that only filters
using mem[] loads/stores pay the price of added security checks.

For other filters, additional cost is a single instruction.

[ Since we access fentry->k a lot now, cache it in a local variable
  and mark filter entry pointer as const. -DaveM ]
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes ax25_getname() doesn't initialize all members of fsa_digipeater
field of fsa struct, also the struct has padding bytes between
sax25_call and sax25_ndigis fields.  This structure is then copied to
userland.  It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Followup of commit ef885afb (net: use rcu_barrier() in
rollback_registered_many)

dst_dev_event() scans a garbage dst list that might be feeded by various
network notifiers at device dismantle time.

Its important to call dst_dev_event() after other notifiers, or we might
enter the infamous msleep(250) in netdev_wait_allrefs(), and wait one
second before calling again call_netdevice_notifiers(NETDEV_UNREGISTER,
dev) to properly remove last device references.

Use priority -10 to let dst_dev_notifier be called after other network
notifiers (they have the default 0 priority)
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.

This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Structure sockaddr_tipc is copied to userland with padding bytes after
"id" field in union field "name" unitialized.  It leads to leaking of
contents of kernel stack memory.  We have to initialize them to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As device_set_wakeup_enable can now sleep, move the call to outside
the critical section.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original patch helps under obscure conditions (no pun) but
some 8168 do not like it. The change needs to be tightened with
a specific 8168 version.

This reverts commit 801e147c
("r8169: Handle rxfifo errors on 8168 chips").

Regression at https://bugzilla.kernel.org/show_bug.cgi?id=20882Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Andreas Radke <a.radke@arcor.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 8723e1b4 (inet: RCU changes in inetdev_by_index())
forgot one call site in ip_mc_drop_socket()

We should not decrease idev refcount after inetdev_by_index() call,
since refcount is not increased anymore.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding the new MacBookAir3,1(2) to btusb.

Output without the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Output with the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This cause 'No Bonding' to be used if userspace has not yet been paired
with remote device since the l2cap socket used to create the rfcomm
session does not have any security level set.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Last commit added a wrong endianness conversion. Fixing that.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of
opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes
access will cause data misalignment exeception.  Use get_unaligned_le16/32
and put_unaligned_le16/32 function to avoid data misalignment execption.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

We've done this for a while in Fedora without any obvious problems other
than some interaction with input devices. Those should be fixed now, so
let's try this in mainline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When initiating dedicated bonding a L2CAP raw socket with HIGH security
level is used. The kernel is supposed to trigger the authentication
request in this case but this doesn't happen currently for non-SSP
(pre-2.1) devices. The reason is that the authentication request happens
in the remote extended features callback which never gets called for
non-SSP devices. This patch fixes the issue by requesting also
authentiation in the (normal) remote features callback in the case of
non-SSP devices.

This rule is applied only for HIGH security level which might at first
seem unintuitive since on the server socket side MEDIUM is already
enough for authentication. However, for the clients we really want to
prefer the server side to decide the authentication requrement in most
cases, and since most client sockets use MEDIUM it's better to be
avoided on the kernel side for these sockets. The important socket to
request it for is the dedicated bonding one and that socket uses HIGH
security level.

The patch is based on the initial investigation and patch proposal from
Andrei Emeltchenko <endrei.emeltchenko@nokia.com>.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Fix kconfig dependency warning to satisfy dependencies:

warning: (BT_HIDP && NET && BT && BT_L2CAP && INPUT || USB_HID && HID_SUPPORT && USB && INPUT) selects HID which has unmet direct dependencies (HID_SUPPORT && INPUT)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>