[ Upstream commit fe0640eb ]

Fixes the objtool warning seen with Clang:
arch/x86/mm/fault.o: warning: objtool: no_context()+0x220: unreachable
instruction

Fixes commit 815f0ddb ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive")

Josh noted that the fallback definition was meant to work around a
pre-gcc-4.6 bug. GCC still needs to work around
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365, so compiler-gcc.h
defines its own version of unreachable().  Clang and ICC can use this
shared definition.

Link: https://github.com/ClangBuiltLinux/linux/issues/204Suggested-by: Andy Lutomirski <luto@amacapital.net>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bd18bffc ]

A VMEnter that VMFails (as opposed to VMExits) does not touch host
state beyond registers that are explicitly noted in the VMFail path,
e.g. EFLAGS.  Host state does not need to be loaded because VMFail
is only signaled for consistency checks that occur before the CPU
starts to load guest state, i.e. there is no need to restore any
state as nothing has been modified.  But in the case where a VMFail
is detected by hardware and not by KVM (due to deferring consistency
checks to hardware), KVM has already loaded some amount of guest
state.  Luckily, "loaded" only means loaded to KVM's software model,
i.e. vmcs01 has not been modified.  So, unwind our software model to
the pre-VMEntry host state.

Not restoring host state in this VMFail path leads to a variety of
failures because we end up with stale data in vcpu->arch, e.g. CR0,
CR4, EFER, etc... will all be out of sync relative to vmcs01.  Any
significant delta in the stale data is all but guaranteed to crash
L1, e.g. emulation of SMEP, SMAP, UMIP, WP, etc... will be wrong.

An alternative to this "soft" reload would be to load host state from
vmcs12 as if we triggered a VMExit (as opposed to VMFail), but that is
wildly inconsistent with respect to the VMX architecture, e.g. an L1
VMM with separate VMExit and VMFail paths would explode.

Note that this approach does not mean KVM is 100% accurate with
respect to VMX hardware behavior, even at an architectural level
(the exact order of consistency checks is microarchitecture specific).
But 100% emulation accuracy isn't the goal (with this patch), rather
the goal is to be consistent in the information delivered to L1, e.g.
a VMExit should not fall-through VMENTER, and a VMFail should not jump
to HOST_RIP.

This technically reverts commit "5af41573 (KVM: nVMX: Fix mmu
context after VMLAUNCH/VMRESUME failure)", but retains the core
aspects of that patch, just in an open coded form due to the need to
pull state from vmcs01 instead of vmcs12.  Restoring host state
resolves a variety of issues introduced by commit "4f350c6d
(kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly)",
which remedied the incorrect behavior of treating VMFail like VMExit
but in doing so neglected to restore arch state that had been modified
prior to attempting nested VMEnter.

A sample failure that occurs due to stale vcpu.arch state is a fault
of some form while emulating an LGDT (due to emulated UMIP) from L1
after a failed VMEntry to L3, in this case when running the KVM unit
test test_tpr_threshold_values in L1.  L0 also hits a WARN in this
case due to a stale arch.cr4.UMIP.

L1:
  BUG: unable to handle kernel paging request at ffffc90000663b9e
  PGD 276512067 P4D 276512067 PUD 276513067 PMD 274efa067 PTE 8000000271de2163
  Oops: 0009 [#1] SMP
  CPU: 5 PID: 12495 Comm: qemu-system-x86 Tainted: G        W         4.18.0-rc2+ #2
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:native_load_gdt+0x0/0x10

  ...

  Call Trace:
   load_fixmap_gdt+0x22/0x30
   __vmx_load_host_state+0x10e/0x1c0 [kvm_intel]
   vmx_switch_vmcs+0x2d/0x50 [kvm_intel]
   nested_vmx_vmexit+0x222/0x9c0 [kvm_intel]
   vmx_handle_exit+0x246/0x15a0 [kvm_intel]
   kvm_arch_vcpu_ioctl_run+0x850/0x1830 [kvm]
   kvm_vcpu_ioctl+0x3a1/0x5c0 [kvm]
   do_vfs_ioctl+0x9f/0x600
   ksys_ioctl+0x66/0x70
   __x64_sys_ioctl+0x16/0x20
   do_syscall_64+0x4f/0x100
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

L0:
  WARNING: CPU: 2 PID: 3529 at arch/x86/kvm/vmx.c:6618 handle_desc+0x28/0x30 [kvm_intel]
  ...
  CPU: 2 PID: 3529 Comm: qemu-system-x86 Not tainted 4.17.2-coffee+ #76
  Hardware name: Intel Corporation Kabylake Client platform/KBL S
  RIP: 0010:handle_desc+0x28/0x30 [kvm_intel]

  ...

  Call Trace:
   kvm_arch_vcpu_ioctl_run+0x863/0x1840 [kvm]
   kvm_vcpu_ioctl+0x3a1/0x5c0 [kvm]
   do_vfs_ioctl+0x9f/0x5e0
   ksys_ioctl+0x66/0x70
   __x64_sys_ioctl+0x16/0x20
   do_syscall_64+0x49/0xf0
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 5af41573 (KVM: nVMX: Fix mmu context after VMLAUNCH/VMRESUME failure)
Fixes: 4f350c6d (kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly)
Cc: Jim Mattson <jmattson@google.com>
Cc: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce9d58d3 ]

Redragon Seymur 2 stops working since commit 190d7f02 ("HID: input:
do not increment usages when a duplicate is found").

Use quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE suggested by the commit
can solve the issue.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200995
BugLink: https://bugs.launchpad.net/bugs/1793846Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ca1721c5 ]

On Apple machines, plugging-in or unplugging the power triggers a GPE
for the EC. Since these machines expose an SBS device, this GPE ends
up triggering the acpi_sbs_callback(). This in turn tries to get the
status of the SBS charger. However, on MBP13,* and MBP14,* machines,
performing the smbus-read operation to get the charger's status triggers
the EC's GPE again. The result is an endless re-triggering and handling
of that GPE, consuming significant CPU resources (> 50% in irq).

In the end this is quite similar to commit 3031cdde (ACPI / SBS:
Don't assume the existence of an SBS charger), except that on the above
machines a status of all 1's is returned. And like there, we just want
ignore the charger here.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=198169Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e0a2e73e ]

Without this usbip fails on a machine with devices
that lexicographically come after vhci_hcd.

ie.
  $ ls -l /sys/devices/platform
  ...
  drwxr-xr-x. 4 root root    0 Sep 19 16:21 serial8250
  -rw-r--r--. 1 root root 4096 Sep 19 23:50 uevent
  drwxr-xr-x. 6 root root    0 Sep 20 13:15 vhci_hcd.0
  drwxr-xr-x. 4 root root    0 Sep 19 16:22 w83627hf.656

Because it detects 'w83627hf.656' as another vhci_hcd controller,
and then fails to be able to talk to it.

Note: this doesn't actually fix usbip's support for multiple
controllers... that's still broken for other reasons
("vhci_hcd.0" is hardcoded in a string macro), but is enough to
actually make it work on the above machine.

See also:
  https://bugzilla.redhat.com/show_bug.cgi?id=1631148

Cc: Jonathan Dieter <jdieter@gmail.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Tested-by: Jonathan Dieter <jdieter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6862fdf2 ]

"S3C2410 PM Suspend Memory CRC" feature (controlled by
SAMSUNG_PM_CHECK config option) is incompatible with highmem
(uses phys_to_virt() instead of proper mapping) which is used by
the majority of Exynos boards. The issue manifests itself in OOPS
on affected boards, i.e. on Odroid-U3 I got the following one:

Unable to handle kernel paging request at virtual address f0000000
pgd = 1c0f9bb4
[f0000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[<c0458034>] (crc32_le) from [<c0121f8c>] (s3c_pm_makecheck+0x34/0x54)
[<c0121f8c>] (s3c_pm_makecheck) from [<c0121efc>] (s3c_pm_run_res+0x74/0x8c)
[<c0121efc>] (s3c_pm_run_res) from [<c0121ecc>] (s3c_pm_run_res+0x44/0x8c)
[<c0121ecc>] (s3c_pm_run_res) from [<c01210b8>] (exynos_suspend_enter+0x64/0x148)
[<c01210b8>] (exynos_suspend_enter) from [<c018893c>] (suspend_devices_and_enter+0x9ec/0xe74)
[<c018893c>] (suspend_devices_and_enter) from [<c0189534>] (pm_suspend+0x770/0xc04)
[<c0189534>] (pm_suspend) from [<c0186ce8>] (state_store+0x6c/0xcc)
[<c0186ce8>] (state_store) from [<c09db434>] (kobj_attr_store+0x14/0x20)
[<c09db434>] (kobj_attr_store) from [<c02fa63c>] (sysfs_kf_write+0x4c/0x50)
[<c02fa63c>] (sysfs_kf_write) from [<c02f97a4>] (kernfs_fop_write+0xfc/0x1e4)
[<c02f97a4>] (kernfs_fop_write) from [<c027b198>] (__vfs_write+0x2c/0x140)
[<c027b198>] (__vfs_write) from [<c027b418>] (vfs_write+0xa4/0x160)
[<c027b418>] (vfs_write) from [<c027b5d8>] (ksys_write+0x40/0x8c)
[<c027b5d8>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)

Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_CHECK config option to hide it on Exynos platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54a58185 ]

Some drivers, for example, QCOM's qdf2xxx, set groups[gpio].name only
when gpio is valid, and leave invalid gpio names as null.
If we want to access the sys node "pinconf-groups",
pinctrl_get_group_selector() -> get_group_name() may return a null
pointer if group_selector is invalid, then the below Kernel panic
would happen since strcmp() uses this null pointer to do comparison.

 Unable to handle kernel NULL pointer dereference at ss 00000000
el:Internal error: Oops: 9600000[ 143.080279]
SMP
 CPU: 19 PID: 2493 Comm: read_all Tainted: G O
.aarch64 #1
 Hardware name: HXT Semiconductor HXT REP-2 System
 PC is at strcmp+0x18/0x154
 LR is at pinctrl_get_group_selector+0x6c/0xe8
 Process read_all (pid: 2493, stack limit =
 Call trace:
 Exception stack
  strcmp+0x18/0x154
  pin_config_group_get+0x64/0xd8
  pinconf_generic_dump_one+0xd8/0x1c0
  pinconf_generic_dump_pins+0x94/0xc8
  pinconf_groups_show+0xb4/0x104
  seq_read+0x178/0x464
  full_proxy_read+0x6c/0xac
  __vfs_read+0x58/0x178
  vfs_read+0x94/0x164
  SyS_read+0x60/0xc0
  __sys_trace_return+0x0/0x4
 --[ end trace]--
 Kernel panic - not syncing: Fatal exception
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9ee3e066 ]

A particular touchpad (SIPODEV SP1064) refuses to supply the HID
descriptors. This patch provides the framework for overriding these
descriptors based on DMI data. It also includes the descriptors for
said touchpad, which were extracted by listening to the traffic of the
windows filter driver, as well as the DMI data for the laptops known
to use this device.

Relevant Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1526312

Cc: Hans de Goede <hdegoede@redhat.com>
Reported-and-tested-by: ahormann@gmx.net
Reported-and-tested-by: Bruno Jesus <bruno.fl.jesus@gmail.com>
Reported-and-tested-by: Dietrich <enaut.w@googlemail.com>
Reported-and-tested-by: kloxdami@yahoo.com
Signed-off-by: Julian Sax <jsbc@gmx.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 30d65e08 ]

Fix crash caused by NULL pointer dereference when debugfs functions
le_max_key_read, le_max_key_size_write, le_min_key_size_read or
le_min_key_size_write and Bluetooth adapter was powered off.

Fix is to move max_key_size and min_key_size from smp_dev to hci_dev.
At the same time they were renamed to le_max_key_size and
le_min_key_size.

BUG: unable to handle kernel NULL pointer dereference at 00000000000002e8
PGD 0 P4D 0
Oops: 0000 [#24] SMP PTI
CPU: 2 PID: 6255 Comm: cat Tainted: G      D    OE     4.18.9-200.fc28.x86_64 #1
Hardware name: LENOVO 4286CTO/4286CTO, BIOS 8DET76WW (1.46 ) 06/21/2018
RIP: 0010:le_max_key_size_read+0x45/0xb0 [bluetooth]
Code: 00 00 00 48 83 ec 10 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 48 8b 87 c8 00 00 00 48 8d 7c 24 04 48 8b 80 48 0a 00 00 <48> 8b 80 e8 02 00 00 0f b6 48 52 e8 fb b6 b3 ed be 04 00 00 00 48
RSP: 0018:ffffab23c3ff3df0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00007f0b4ca2e000 RCX: ffffab23c3ff3f08
RDX: ffffffffc0ddb033 RSI: 0000000000000004 RDI: ffffab23c3ff3df4
RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffab23c3ff3ed8 R11: 0000000000000000 R12: ffffab23c3ff3f08
R13: 00007f0b4ca2e000 R14: 0000000000020000 R15: ffffab23c3ff3f08
FS:  00007f0b4ca0f540(0000) GS:ffff91bd5e280000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000002e8 CR3: 00000000629fa006 CR4: 00000000000606e0
Call Trace:
 full_proxy_read+0x53/0x80
 __vfs_read+0x36/0x180
 vfs_read+0x8a/0x140
 ksys_read+0x4f/0xb0
 do_syscall_64+0x5b/0x160
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4add7104 ]

If au0828_analog_register fails, the dev is kfree'd and then flow
jumps to done, which can call au0828_usb_disconnect. Since all USB
error codes are negative, au0828_usb_disconnect will be called. The
problem is au0828_usb_disconnect uses dev, if dev is NULL then there
is immediate oops encountered.

[    7.454307] au0828: au0828_usb_probe() au0282_dev_register failed to register on V4L2
[    7.454323] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[    7.454421] PGD 0 P4D 0
[    7.454457] Oops: 0002 [#1] SMP PTI
[    7.454500] CPU: 1 PID: 262 Comm: systemd-udevd Tainted: P           O      4.18.3 #1
[    7.454584] Hardware name: Google Panther/Panther, BIOS MattDevo 04/27/2015
[    7.454670] RIP: 0010:_raw_spin_lock_irqsave+0x2c/0x50
[    7.454725] Code: 44 00 00 55 48 89 e5 41 54 53 48 89 fb 9c 58 0f 1f 44 00 00 49 89 c4 fa 66 0f 1f 44 00 00 e8 db 23 1b ff 31 c0 ba 01 00 00 00 <f0> 0f b1 13 85 c0 75 08 4c 89 e0 5b 41 5c 5d c3 89 c6 48 89 df e8
[    7.455004] RSP: 0018:ffff9130f53ef988 EFLAGS: 00010046
[    7.455063] RAX: 0000000000000000 RBX: 0000000000000050 RCX: 0000000000000000
[    7.455139] RDX: 0000000000000001 RSI: 0000000000000003 RDI: 0000000000000050
[    7.455216] RBP: ffff9130f53ef998 R08: 0000000000000018 R09: 0000000000000090
[    7.455292] R10: ffffed4cc53cb000 R11: ffffed4cc53cb108 R12: 0000000000000082
[    7.455369] R13: ffff9130cf2c6188 R14: 0000000000000000 R15: 0000000000000018
[    7.455447] FS:  00007f2ff8514cc0(0000) GS:ffff9130fcb00000(0000) knlGS:0000000000000000
[    7.455535] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    7.455597] CR2: 0000000000000050 CR3: 00000001753f0002 CR4: 00000000000606a0
[    7.455675] Call Trace:
[    7.455713]  __wake_up_common_lock+0x65/0xc0
[    7.455764]  __wake_up+0x13/0x20
[    7.455808]  ir_lirc_unregister+0x57/0xe0 [rc_core]
[    7.455865]  rc_unregister_device+0xa0/0xc0 [rc_core]
[    7.455935]  au0828_rc_unregister+0x25/0x40 [au0828]
[    7.455999]  au0828_usb_disconnect+0x33/0x80 [au0828]
[    7.456064]  au0828_usb_probe.cold.16+0x8d/0x2aa [au0828]
[    7.456130]  usb_probe_interface+0xf1/0x300
[    7.456184]  driver_probe_device+0x2e3/0x460
[    7.456235]  __driver_attach+0xe4/0x110
[    7.456282]  ? driver_probe_device+0x460/0x460
[    7.456335]  bus_for_each_dev+0x74/0xb0
[    7.456385]  ? kmem_cache_alloc_trace+0x15d/0x1d0
[    7.456441]  driver_attach+0x1e/0x20
[    7.456485]  bus_add_driver+0x159/0x230
[    7.456532]  driver_register+0x70/0xc0
[    7.456578]  usb_register_driver+0x7f/0x140
[    7.456626]  ? 0xffffffffc0474000
[    7.456674]  au0828_init+0xbc/0x1000 [au0828]
[    7.456725]  do_one_initcall+0x4a/0x1c9
[    7.456771]  ? _cond_resched+0x19/0x30
[    7.456817]  ? kmem_cache_alloc_trace+0x15d/0x1d0
[    7.456873]  do_init_module+0x60/0x210
[    7.456918]  load_module+0x221b/0x2710
[    7.456966]  ? vfs_read+0xf5/0x120
[    7.457010]  __do_sys_finit_module+0xbd/0x120
[    7.457061]  ? __do_sys_finit_module+0xbd/0x120
[    7.457115]  __x64_sys_finit_module+0x1a/0x20
[    7.457166]  do_syscall_64+0x5b/0x110
[    7.457210]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cd24e457 ]

When a PRRN event is received we are already running in a worker
thread. Instead of spawning off another worker thread on the prrn_work
workqueue to handle the PRRN event we can just call the PRRN handler
routine directly.

With this update we can also pass the scope variable for the PRRN
event directly to the handler instead of it being a global variable.

This patch fixes the following oops mnessage we are seeing in PRRN testing:

  Oops: Bad kernel stack pointer, sig: 6 [#1]
  SMP NR_CPUS=2048 NUMA pSeries
  Modules linked in: nfsv3 nfs_acl rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache binfmt_misc reiserfs vfat fat rpadlpar_io(X) rpaphp(X) tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag af_packet xfs libcrc32c dm_service_time ibmveth(X) ses enclosure scsi_transport_sas rtc_generic btrfs xor raid6_pq sd_mod ibmvscsi(X) scsi_transport_srp ipr(X) libata sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4
  Supported: Yes, External                                                     54
  CPU: 7 PID: 18967 Comm: kworker/u96:0 Tainted: G                 X 4.4.126-94.22-default #1
  Workqueue: pseries hotplug workque pseries_hp_work_fn
  task: c000000775367790 ti: c00000001ebd4000 task.ti: c00000070d140000
  NIP: 0000000000000000 LR: 000000001fb3d050 CTR: 0000000000000000
  REGS: c00000001ebd7d40 TRAP: 0700   Tainted: G                 X  (4.4.126-94.22-default)
  MSR: 8000000102081000 <41,VEC,ME5  CR: 28000002  XER: 20040018   4
  CFAR: 000000001fb3d084 40 419   1                                3
  GPR00: 000000000000000040000000000010007 000000001ffff400 000000041fffe200
  GPR04: 000000000000008050000000000000000 000000001fb15fa8 0000000500000500
  GPR08: 000000000001f40040000000000000001 0000000000000000 000005:5200040002
  GPR12: 00000000000000005c000000007a05400 c0000000000e89f8 000000001ed9f668
  GPR16: 000000001fbeff944000000001fbeff94 000000001fb545e4 0000006000000060
  GPR20: ffffffffffffffff4ffffffffffffffff 0000000000000000 0000000000000000
  GPR24: 00000000000000005400000001fb3c000 0000000000000000 000000001fb1b040
  GPR28: 000000001fb240004000000001fb440d8 0000000000000008 0000000000000000
  NIP [0000000000000000] 5         (null)
  LR [000000001fb3d050] 031fb3d050
  Call Trace:            4
  Instruction dump:      4                                       5:47 12    2
  XXXXXXXX XXXXXXXX XXXXX4XX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
  XXXXXXXX XXXXXXXX XXXXX5XX XXXXXXXX 60000000 60000000 60000000 60000000
  ---[ end trace aa5627b04a7d9d6b ]---                                       3NMI watchdog: BUG: soft lockup - CPU#27 stuck for 23s! [kworker/27:0:13903]
  Modules linked in: nfsv3 nfs_acl rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache binfmt_misc reiserfs vfat fat rpadlpar_io(X) rpaphp(X) tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag af_packet xfs libcrc32c dm_service_time ibmveth(X) ses enclosure scsi_transport_sas rtc_generic btrfs xor raid6_pq sd_mod ibmvscsi(X) scsi_transport_srp ipr(X) libata sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4
  Supported: Yes, External
  CPU: 27 PID: 13903 Comm: kworker/27:0 Tainted: G      D          X 4.4.126-94.22-default #1
  Workqueue: events prrn_work_fn
  task: c000000747cfa390 ti: c00000074712c000 task.ti: c00000074712c000
  NIP: c0000000008002a8 LR: c000000000090770 CTR: 000000000032e088
  REGS: c00000074712f7b0 TRAP: 0901   Tainted: G      D          X  (4.4.126-94.22-default)
  MSR: 8000000100009033 <SF,EE,ME,IR,DR,RI,LE>  CR: 22482044  XER: 20040000
  CFAR: c0000000008002c4 SOFTE: 1
  GPR00: c000000000090770 c00000074712fa30 c000000000f09800 c000000000fa1928 6:02
  GPR04: c000000775f5e000 fffffffffffffffe 0000000000000001 c000000000f42db8
  GPR08: 0000000000000001 0000000080000007 0000000000000000 0000000000000000
  GPR12: 8006210083180000 c000000007a14400
  NIP [c0000000008002a8] _raw_spin_lock+0x68/0xd0
  LR [c000000000090770] mobility_rtas_call+0x50/0x100
  Call Trace:            59                                        5
  [c00000074712fa60] [c000000000090770] mobility_rtas_call+0x50/0x100
  [c00000074712faf0] [c000000000090b08] pseries_devicetree_update+0xf8/0x530
  [c00000074712fc20] [c000000000031ba4] prrn_work_fn+0x34/0x50
  [c00000074712fc40] [c0000000000e0390] process_one_work+0x1a0/0x4e0
  [c00000074712fcd0] [c0000000000e0870] worker_thread+0x1a0/0x6105:57       2
  [c00000074712fd80] [c0000000000e8b18] kthread+0x128/0x150
  [c00000074712fe30] [c0000000000096f8] ret_from_kernel_thread+0x5c/0x64
  Instruction dump:
  2c090000 40c20010 7d40192d 40c2fff0 7c2004ac 2fa90000 40de0018 5:540030   3
  e8010010 ebe1fff8 7c0803a6 4e800020 <7c210b78> e92d0000 89290009 792affe3
Signed-off-by: John Allen <jallen@linux.ibm.com>
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4bb1ce23 ]

When console device is rebinded, console_setup() is called again.
But marking it as __init means that function will be clear after boot is
complete. If console device is binded again console_setup() is not found
and error "Unable to handle kernel paging request at virtual address"
is reported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0d704967 ]

cgroup v2 path field is PATH_MAX which is too large, this is placing too
much pressure on memory allocation for people with many rules doing
cgroup v1 classid matching, side effects of this are bug reports like:

https://bugzilla.kernel.org/show_bug.cgi?id=200639

This patch registers a new revision that shrinks the cgroup path to 512
bytes, which is the same approach we follow in similar extensions that
have a path field.

Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 042be0f8 ]

https://bugzilla.kernel.org/show_bug.cgi?id=200219

Reproduction way:
- mount image
- run poc code
- umount image

F2FS-fs (loop1): Bitmap was wrongly set, blk:15364
------------[ cut here ]------------
kernel BUG at /home/yuchao/git/devf2fs/segment.c:2061!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 2 PID: 17686 Comm: umount Tainted: G        W  O      4.18.0-rc2+ #39
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
EIP: update_sit_entry+0x459/0x4e0 [f2fs]
Code: e8 1c b5 fd ff 0f 0b 0f 0b 8b 45 e4 c7 44 24 08 9c 7a 6c f8 c7 44 24 04 bc 4a 6c f8 89 44 24 0c 8b 06 89 04 24 e8 f7 b4 fd ff <0f> 0b 8b 45 e4 0f b6 d2 89 54 24 10 c7 44 24 08 60 7a 6c f8 c7 44
EAX: 00000032 EBX: 000000f8 ECX: 00000002 EDX: 00000001
ESI: d7177000 EDI: f520fe68 EBP: d6477c6c ESP: d6477c34
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010282
CR0: 80050033 CR2: b7fbe000 CR3: 2a99b3c0 CR4: 000406f0
Call Trace:
 f2fs_allocate_data_block+0x124/0x580 [f2fs]
 do_write_page+0x78/0x150 [f2fs]
 f2fs_do_write_node_page+0x25/0xa0 [f2fs]
 __write_node_page+0x2bf/0x550 [f2fs]
 f2fs_sync_node_pages+0x60e/0x6d0 [f2fs]
 ? sync_inode_metadata+0x2f/0x40
 ? f2fs_write_checkpoint+0x28f/0x7d0 [f2fs]
 ? up_write+0x1e/0x80
 f2fs_write_checkpoint+0x2a9/0x7d0 [f2fs]
 ? mark_held_locks+0x5d/0x80
 ? _raw_spin_unlock_irq+0x27/0x50
 kill_f2fs_super+0x68/0x90 [f2fs]
 deactivate_locked_super+0x3d/0x70
 deactivate_super+0x40/0x60
 cleanup_mnt+0x39/0x70
 __cleanup_mnt+0x10/0x20
 task_work_run+0x81/0xa0
 exit_to_usermode_loop+0x59/0xa7
 do_fast_syscall_32+0x1f5/0x22c
 entry_SYSENTER_32+0x53/0x86
EIP: 0xb7f95c51
Code: c1 1e f7 ff ff 89 e5 8b 55 08 85 d2 8b 81 64 cd ff ff 74 02 89 02 5d c3 8b 0c 24 c3 8b 1c 24 c3 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d 76 00 58 b8 77 00 00 00 cd 80 90 8d 76
EAX: 00000000 EBX: 0871ab90 ECX: bfb2cd00 EDX: 00000000
ESI: 00000000 EDI: 0871ab90 EBP: 0871ab90 ESP: bfb2cd7c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b EFLAGS: 00000246
Modules linked in: f2fs(O) crc32_generic bnep rfcomm bluetooth ecdh_generic snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq pcbc joydev aesni_intel snd_seq_device aes_i586 snd_timer crypto_simd snd cryptd soundcore mac_hid serio_raw video i2c_piix4 parport_pc ppdev lp parport hid_generic psmouse usbhid hid e1000 [last unloaded: f2fs]
---[ end trace d423f83982cfcdc5 ]---

The reason is, different log headers using the same segment, once
one log's next block address is used by another log, it will cause
panic as above.

Main area: 24 segs, 24 secs 24 zones
  - COLD  data: 0, 0, 0
  - WARM  data: 1, 1, 1
  - HOT   data: 20, 20, 20
  - Dir   dnode: 22, 22, 22
  - File   dnode: 22, 22, 22
  - Indir nodes: 21, 21, 21

So this patch adds sanity check to detect such condition to avoid
this issue.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ae7d1247 ]

In functions snd_soc_get_volsw_sx() or snd_soc_put_volsw_sx(),
if the result of (min + max) is negative, then fls() returns
signed integer with value as 32. This leads to signed integer
overflow as complete operation is considered as signed integer.

UBSAN: Undefined behaviour in sound/soc/soc-ops.c:382:50
signed integer overflow:
-2147483648 - 1 cannot be represented in type 'int'
Call trace:
[<ffffff852f746fe4>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffff852f746fe4>] dump_stack+0xec/0x158 lib/dump_stack.c:51
[<ffffff852f7b5f3c>] ubsan_epilogue+0x18/0x50 lib/ubsan.c:164
[<ffffff852f7b6840>] handle_overflow+0xf8/0x130 lib/ubsan.c:195
[<ffffff852f7b68f0>] __ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:211
[<ffffff85307971a0>] snd_soc_get_volsw_sx+0x1a8/0x1f8 sound/soc/soc-ops.c:382

Typecast the operation to unsigned int to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5e172f75 ]

The default P9_LOCK_TIMEOUT can be too long for some users exporting
a local file system to a guest VM (30s), make this configurable at
mount time.

Link: http://lkml.kernel.org/r/1536295827-3181-1-git-send-email-asmadeus@codewreck.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195727Signed-off-by: Dinu-Razvan Chis-Serban <justcsdr@gmail.com>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2803cf43 ]

v9fs_dir_readdir() could deadloop if a struct was sent with a size set
to -2

Link: http://lkml.kernel.org/r/1536134432-11997-1-git-send-email-asmadeus@codewreck.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88021Signed-off-by: Gertjan Halkes <gertjan@google.com>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7d20c8ab ]

https://bugzilla.kernel.org/show_bug.cgi?id=200951

These is a NULL pointer dereference issue reported in bugzilla:

Hi,
in the setup there is a SATA SSD connected to a SATA-to-USB bridge.

The disc is "Samsung SSD 850 PRO 256G" which supports TRIM.
There are four partitions:
 sda1: FAT  /boot
 sda2: F2FS /
 sda3: F2FS /home
 sda4: F2FS

The bridge is ASMT1153e which uses the "uas" driver.
There is no TRIM pass-through, so, when mounting it reports:
 mounting with "discard" option, but the device does not support discard

The USB host is USB3.0 and UASP capable. It is the one on RK3399.

Given this everything works fine, except there is no TRIM support.

In order to enable TRIM a new UDEV rule is added [1]:
 /etc/udev/rules.d/10-sata-bridge-trim.rules:
 ACTION=="add|change", ATTRS{idVendor}=="174c", ATTRS{idProduct}=="55aa", SUBSYSTEM=="scsi_disk", ATTR{provisioning_mode}="unmap"
After reboot any F2FS write hangs forever and dmesg reports:
 Unable to handle kernel NULL pointer dereference

Also tested on a x86_64 system: works fine even with TRIM enabled.
 same disc
 same bridge
 different usb host controller
 different cpu architecture
 not root filesystem

Regards,
  Vicenç.

[1] Post #5 in https://bbs.archlinux.org/viewtopic.php?id=236280

 Unable to handle kernel NULL pointer dereference at virtual address 000000000000003e
 Mem abort info:
   ESR = 0x96000004
   Exception class = DABT (current EL), IL = 32 bits
   SET = 0, FnV = 0
   EA = 0, S1PTW = 0
 Data abort info:
   ISV = 0, ISS = 0x00000004
   CM = 0, WnR = 0
 user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000626e3122
 [000000000000003e] pgd=0000000000000000
 Internal error: Oops: 96000004 [#1] SMP
 Modules linked in: overlay snd_soc_hdmi_codec rc_cec dw_hdmi_i2s_audio dw_hdmi_cec snd_soc_simple_card snd_soc_simple_card_utils snd_soc_rockchip_i2s rockchip_rga snd_soc_rockchip_pcm rockchipdrm videobuf2_dma_sg v4l2_mem2mem rtc_rk808 videobuf2_memops analogix_dp videobuf2_v4l2 videobuf2_common dw_hdmi dw_wdt cec rc_core videodev drm_kms_helper media drm rockchip_thermal rockchip_saradc realtek drm_panel_orientation_quirks syscopyarea sysfillrect sysimgblt fb_sys_fops dwmac_rk stmmac_platform stmmac pwm_bl squashfs loop crypto_user gpio_keys hid_kensington
 CPU: 5 PID: 957 Comm: nvim Not tainted 4.19.0-rc1-1-ARCH #1
 Hardware name: Sapphire-RK3399 Board (DT)
 pstate: 00000005 (nzcv daif -PAN -UAO)
 pc : update_sit_entry+0x304/0x4b0
 lr : update_sit_entry+0x108/0x4b0
 sp : ffff00000ca13bd0
 x29: ffff00000ca13bd0 x28: 000000000000003e
 x27: 0000000000000020 x26: 0000000000080000
 x25: 0000000000000048 x24: ffff8000ebb85cf8
 x23: 0000000000000253 x22: 00000000ffffffff
 x21: 00000000000535f2 x20: 00000000ffffffdf
 x19: ffff8000eb9e6800 x18: ffff8000eb9e6be8
 x17: 0000000007ce6926 x16: 000000001c83ffa8
 x15: 0000000000000000 x14: ffff8000f602df90
 x13: 0000000000000006 x12: 0000000000000040
 x11: 0000000000000228 x10: 0000000000000000
 x9 : 0000000000000000 x8 : 0000000000000000
 x7 : 00000000000535f2 x6 : ffff8000ebff3440
 x5 : ffff8000ebff3440 x4 : ffff8000ebe3a6c8
 x3 : 00000000ffffffff x2 : 0000000000000020
 x1 : 0000000000000000 x0 : ffff8000eb9e5800
 Process nvim (pid: 957, stack limit = 0x0000000063a78320)
 Call trace:
  update_sit_entry+0x304/0x4b0
  f2fs_invalidate_blocks+0x98/0x140
  truncate_node+0x90/0x400
  f2fs_remove_inode_page+0xe8/0x340
  f2fs_evict_inode+0x2b0/0x408
  evict+0xe0/0x1e0
  iput+0x160/0x260
  do_unlinkat+0x214/0x298
  __arm64_sys_unlinkat+0x3c/0x68
  el0_svc_handler+0x94/0x118
  el0_svc+0x8/0xc
 Code: f9400800 b9488400 36080140 f9400f01 (387c4820)
 ---[ end trace a0f21a307118c477 ]---

The reason is it is possible to enable discard flag on block queue via
UDEV, but during mount, f2fs will initialize se->discard_map only if
this flag is set, once the flag is set after mount, f2fs may dereference
NULL pointer on se->discard_map.

So this patch does below changes to fix this issue:
- initialize and update se->discard_map all the time.
- don't clear DISCARD option if device has no QUEUE_FLAG_DISCARD flag
during mount.
- don't issue small discard on zoned block device.
- introduce some functions to enhance the readability.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4c62764d ]

While running regressions, observed below kernel panic when sdio disconnect
called. This is because of, kthread_stop() is taking care of
wait_for_completion() by default. When wait_for_completion triggered
in kthread_stop and as it was done already, giving kernel panic.
Hence, removing redundant wait_for_completion() from rsi_kill_thread().

... skipping ...
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff810a63df>] exit_creds+0x1f/0x50
PGD 0
Oops: 0002 [#1] SMP
CPU: 0 PID: 6502 Comm: rmmod Tainted: G  OE   4.15.9-Generic #154-Ubuntu
Hardware name: Dell Inc. Edge Gateway 3003/ , BIOS 01.00.00 04/17/2017
Stack:
ffff88007392e600 ffff880075847dc0 ffffffff8108160a 0000000000000000
ffff88007392e600 ffff880075847de8 ffffffff810a484b ffff880076127000
ffff88003cd3a800 ffff880074f12a00 ffff880075847e28 ffffffffc09bed15
Call Trace:
[<ffffffff8108160a>] __put_task_struct+0x5a/0x140
[<ffffffff810a484b>] kthread_stop+0x10b/0x110
[<ffffffffc09bed15>] rsi_disconnect+0x2f5/0x300 [ven_rsi_sdio]
[<ffffffff81578bcb>] ? __pm_runtime_resume+0x5b/0x80
[<ffffffff816f0918>] sdio_bus_remove+0x38/0x100
[<ffffffff8156cc64>] __device_release_driver+0xa4/0x150
[<ffffffff8156d7a5>] driver_detach+0xb5/0xc0
[<ffffffff8156c6c5>] bus_remove_driver+0x55/0xd0
[<ffffffff8156dfbc>] driver_unregister+0x2c/0x50
[<ffffffff816f0b8a>] sdio_unregister_driver+0x1a/0x20
[<ffffffffc09bf0f5>] rsi_module_exit+0x15/0x30 [ven_rsi_sdio]
[<ffffffff8110cad8>] SyS_delete_module+0x1b8/0x210
[<ffffffff81851dc8>] entry_SYSCALL_64_fastpath+0x1c/0xbb
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9ce3ebe9 ]

In the corner case where the gpio driver probe fails, for whatever
reason, the suspend and resume handlers will still be called as they
have to be registered as syscore operations. This applies as well when
no probe was called while the driver has been built in the kernel.

Nicolas tracked this in :
https://bugzilla.kernel.org/show_bug.cgi?id=200905

Therefore, add a failsafe in these function, and test if a proper probe
succeeded and the driver is functional.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit abf7b30d ]

In the Cirrus driver, the regular clean-up code also performs the clean-up
of a failed initialization. If the fbdev's framebuffer was not initialized,
the clean-up will fail within drm_framebuffer_unregister_private. Booting
with cirrus.bpp=16 triggers this bug.

The framebuffer is currently stored directly within struct cirrus_fbdev. To
fix the bug, we turn it into a pointer that is only set for initialized
framebuffers. The fbdev's clean-up code skips uninitialized framebuffers.

The memory for struct drm_framebuffer is allocated dynamically. This requires
additional error handling within cirrusfb_create. The framebuffer clean-up is
now performed by drm_framebuffer_put, which also frees the data strcuture's
memory.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1101822Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20180720112743.27159-1-tzimmermann@suse.deSigned-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 18915b58 ]

The ext4 fstrim implementation uses the block bitmaps to find free space
that can be discarded.  If we haven't replayed the journal, the bitmaps
will be stale and we absolutely *cannot* use stale metadata to zap the
underlying storage.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ffc8599a ]

On machines where the GART aperture is mapped over physical RAM,
/proc/kcore contains the GART aperture range. Accessing the GART range via
/proc/kcore results in a kernel crash.

vmcore used to have the same issue, until it was fixed with commit
2a3e83c6 ("x86/gart: Exclude GART aperture from vmcore")', leveraging
existing hook infrastructure in vmcore to let /proc/vmcore return zeroes
when attempting to read the aperture region, and so it won't read from the
actual memory.

Apply the same workaround for kcore. First implement the same hook
infrastructure for kcore, then reuse the hook functions introduced in the
previous vmcore fix. Just with some minor adjustment, rename some functions
for more general usage, and simplify the hook infrastructure a bit as there
is no module usage yet.
Suggested-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Dave Young <dyoung@redhat.com>
Link: https://lkml.kernel.org/r/20190308030508.13548-1-kasong@redhat.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 85f9987b ]

It was mapped to EIO which can be confusing when user space
queries for an object GUID for an object for which the server
file system doesn't support (or hasn't saved one).

As Amir Goldstein suggested this is similar to ENOATTR
(equivalently ENODATA in Linux errno definitions) so
changing NT STATUS code mapping for OBJECTID_NOT_FOUND
to ENODATA.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e898e69d ]

When building with -Wsometimes-uninitialized, Clang warns:

arch/x86/kernel/hw_breakpoint.c:355:2: warning: variable 'align' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]

The default cannot be reached because arch_build_bp_info() initializes
hw->len to one of the specified cases. Nevertheless the warning is valid
and returning -EINVAL makes sure that this cannot be broken by future
modifications.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/392
Link: https://lkml.kernel.org/r/20190307212756.4648-1-natechancellor@gmail.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5bb71fc7 ]

The spec states in 10.4.16 that the Protected Memory Enable
Register should be treated as read-only for implementations
not supporting protected memory regions (PLMR and PHMR fields
reported as Clear in the Capability register).

Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: mark gross <mgross@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: f8bab735 ("intel-iommu: PMEN support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 909e9c9c ]

pm_runtime_get_sync returns negative on failure.

Fixes: eaeb9010 ("drm/nouveau/debugfs: Wake up GPU before doing any reclocking")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 18fb053f ]

There are comments in processor-cyrix.h advising you to _not_ make calls
using the deprecated macros in this style:

  setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);

This is because it expands the macro into a non-functioning calling
sequence. The calling order must be:

  outb(CX86_CCR2, 0x22);
  inb(0x23);

From the comments:

 * When using the old macros a line like
 *   setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
 * gets expanded to:
 *  do {
 *    outb((CX86_CCR2), 0x22);
 *    outb((({
 *        outb((CX86_CCR2), 0x22);
 *        inb(0x23);
 *    }) | 0x88), 0x23);
 *  } while (0);

The new macros fix this problem, so use them instead. Tested on an
actual Geode processor.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@kernel.org
Link: https://lkml.kernel.org/r/1552596361-8967-2-git-send-email-tedheadster@gmail.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 534c89c2 ]

The page allocation in hv_cpu_init() can fail, but the code does not
have a check for that.

Add a check and return -ENOMEM when the allocation fails.

[ tglx: Massaged changelog ]
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Acked-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: pakki001@umn.edu
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-hyperv@vger.kernel.org
Link: https://lkml.kernel.org/r/20190314054651.1315-1-kjlu@umn.eduSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2e84f116 ]

hpet_virt_address may be NULL when ioremap_nocache fail, but the code lacks
a check.

Add a check to prevent NULL pointer dereference.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: kjlu@umn.edu
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Link: https://lkml.kernel.org/r/20190319021958.17275-1-pakki001@umn.eduSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fca269f2 ]

mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.

The eventid clear call trace:
                free_irq
                __free_irq
                irq_shutdown
                irq_domain_deactivate_irq
                __irq_domain_deactivate_irq
                __irq_domain_deactivate_irq
                msi_domain_deactivate
                platform_msi_write_msg
                mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0dda0966 ]

Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.

Fixes: f9fc1745 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6a3b45ad ]

MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
  ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
  ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:

[   25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[   25.677888] ------------[ cut here ]------------
[   25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[   25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[   25.693778] Modules linked in:
[   25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[   25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[   25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[   25.716470] LR is at lock_is_held_type+0x44/0x64

v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 373e915c ]

This patch avoids that the following warning is reported when building
with W=1:

block/blk-iolatency.c:734:5: warning: no previous prototype for 'blk_iolatency_init' [-Wmissing-prototypes]

Cc: Josef Bacik <jbacik@fb.com>
Fixes: d7067512 ("block: introduce blk-iolatency io controller") # v4.19
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2071ac98 ]

Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
  clk_register()
    __clk_core_init()
      clk_prepare_lock()                            ----> acquires prepare_lock
        cs2000_recalc_rate()
          i2c_smbus_read_byte_data()
            rcar_i2c_master_xfer()
              dma_request_chan()
                rcar_dmac_of_xlate()
                  rcar_dmac_alloc_chan_resources()
                    pm_runtime_get_sync()
                      __pm_runtime_resume()
                        rpm_resume()
                          rpm_callback()
                            genpd_runtime_resume()   ----> acquires genpd->mlock

Second thread is attaching any device to the same PM domain
genpd_add_device()
  genpd_lock()                                       ----> acquires genpd->mlock
    cpg_mssr_attach_dev()
      of_clk_get_from_provider()
        __of_clk_get_from_provider()
          __clk_create_clk()
            clk_prepare_lock()                       ----> acquires prepare_lock

Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54e3aca8 ]

When commit 8661423e ("ACPI / utils: Add new acpi_dev_present
helper") introduced acpi_dev_present(), it missed the fact that
bus_find_device() took a reference on the device found by it and
the callers of acpi_dev_present() don't drop that reference.

Drop the reference on the device in acpi_dev_present().

Fixes: 8661423e ("ACPI / utils: Add new acpi_dev_present helper")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d982b331 ]

  =================================================================
  ==20875==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 1160 byte(s) in 1 object(s) allocated from:
      #0 0x7f1b6fc84138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x55bd50005599 in zalloc util/util.h:23
      #2 0x55bd500068f5 in perf_evsel__newtp_idx util/evsel.c:327
      #3 0x55bd4ff810fc in perf_evsel__newtp /home/work/linux/tools/perf/util/evsel.h:216
      #4 0x55bd4ff81608 in test__perf_evsel__tp_sched_test tests/evsel-tp-sched.c:69
      #5 0x55bd4ff528e6 in run_test tests/builtin-test.c:358
      #6 0x55bd4ff52baf in test_and_print tests/builtin-test.c:388
      #7 0x55bd4ff543fe in __cmd_test tests/builtin-test.c:583
      #8 0x55bd4ff5572f in cmd_test tests/builtin-test.c:722
      #9 0x55bd4ffc4087 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #10 0x55bd4ffc45c6 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #11 0x55bd4ffc49ca in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #12 0x55bd4ffc5138 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #13 0x7f1b6e34809a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  Indirect leak of 19 byte(s) in 1 object(s) allocated from:
      #0 0x7f1b6fc83f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
      #1 0x7f1b6e3ac30f in vasprintf (/lib/x86_64-linux-gnu/libc.so.6+0x8830f)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 6a6cd11d ("perf test: Add test for the sched tracepoint format fields")
Link: http://lkml.kernel.org/r/20190316080556.3075-17-changbin.du@gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f97a8991 ]

  =================================================================
  ==7506==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 13 byte(s) in 3 object(s) allocated from:
      #0 0x7f03339d6070 in __interceptor_strdup (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x3b070)
      #1 0x5625e53aaef0 in expr__find_other util/expr.y:221
      #2 0x5625e51bcd3f in test__expr tests/expr.c:52
      #3 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #4 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #5 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #6 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #7 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #8 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #9 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #10 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #11 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 07516736 ("perf tools: Add a simple expression parser for JSON")
Link: http://lkml.kernel.org/r/20190316080556.3075-16-changbin.du@gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 93faa52e ]

  =================================================================
  ==7497==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 40 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a88f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
      #1 0x5625e5326213 in cpu_map__trim_new util/cpumap.c:45
      #2 0x5625e5326703 in cpu_map__read util/cpumap.c:103
      #3 0x5625e53267ef in cpu_map__read_all_cpu_map util/cpumap.c:120
      #4 0x5625e5326915 in cpu_map__new util/cpumap.c:135
      #5 0x5625e517b355 in test__openat_syscall_event_on_all_cpus tests/openat-syscall-all-cpus.c:36
      #6 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #7 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #8 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #9 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #10 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #11 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #12 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #13 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #14 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: f30a79b0 ("perf tools: Add reference counting for cpu_map object")
Link: http://lkml.kernel.org/r/20190316080556.3075-15-changbin.du@gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 42dfa451 ]

Using gcc's ASan, Changbin reports:

  =================================================================
  ==7494==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 48 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x5625e5330a5e in zalloc util/util.h:23
      #2 0x5625e5330a9b in perf_counts__new util/counts.c:10
      #3 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47
      #4 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505
      #5 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347
      #6 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47
      #7 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #8 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #9 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #10 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #11 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #12 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #13 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #14 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #15 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  Indirect leak of 72 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x5625e532560d in zalloc util/util.h:23
      #2 0x5625e532566b in xyarray__new util/xyarray.c:10
      #3 0x5625e5330aba in perf_counts__new util/counts.c:15
      #4 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47
      #5 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505
      #6 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347
      #7 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47
      #8 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #9 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #10 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #11 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #12 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #13 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #14 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #15 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #16 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

His patch took care of evsel->prev_raw_counts, but the above backtraces
are about evsel->counts, so fix that instead.
Reported-by: Changbin Du <changbin.du@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/n/tip-hd1x13g59f0nuhe4anxhsmfp@git.kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>