- 04 Jun, 2024 33 commits
-
-
Julien Stephan authored
Add compatible support for ad7380/1/3/4-4 parts which are 4 channels variants from ad7380/1/3/4 Signed-off-by:
Julien Stephan <jstephan@baylibre.com> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20240528-adding-new-ad738x-driver-v7-6-4cd70a4c12c8@baylibre.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Julien Stephan authored
The current driver supports only parts with 2 channels. In order to prepare the support of new compatible ADCs with more channels, this commit: - defines MAX_NUM_CHANNEL to specify the maximum number of channels currently supported by the driver - adds available_scan_mask member in ad7380_chip_info structure - fixes spi xfer struct len depending on number of channels - fixes scan_data.raw buffer size to handle more channels - adds a timing specifications structure in ad7380_chip_info structure Signed-off-by: -
David Lechner authored
Add support for AD7383, AD7384 pseudo-differential compatible parts. Pseudo differential parts require common mode voltage supplies so add the support for them and add the support of IIO_CHAN_INFO_OFFSET to retrieve the offset Signed-off-by:
David Lechner <dlechner@baylibre.com> Signed-off-by:
-
David Lechner authored
Adding AD7383 and AD7384 compatible parts that are pseudo-differential. Pseudo-differential require common mode voltage supplies, so add them conditionally Signed-off-by:
-
David Lechner authored
This adds a new driver for the AD7380 family ADCs. The driver currently implements basic support for the AD7380, AD7381, 2-channel differential ADCs. Support for additional single-ended, pseudo-differential and 4-channel chips that use the same register map as well as additional features of the chip will be added in future patches. [Julien Stephan: fix rx/tx buffer for regmap access] [Julien Stephan: fix scale issue] [Julien Stephan: use the new iio_device_claim_direct_scoped instead of iio_device_claim_direct_mode] Co-developed-by:
Stefan Popa <stefan.popa@analog.com> Signed-off-by:
Nuno Sa <nuno.sa@analog.com> Signed-off-by:
-
David Lechner authored
This adds a binding specification for the Analog Devices Inc. AD7380 family of ADCs. Signed-off-by:
-
Nuno Sa authored
When enabling the core, make sure DRP (Dynamic Reconfiguration Port) is locked. Most of the designs don't really use it but we still get the lock bit set. So let's do it all the time so the code is generic. While at it reduce the timeout time to 1 microsecond as it seems to be enough and goes in line with what we have on the similar DAC core (adi-axi-dac). Signed-off-by:
-
Nuno Sa authored
Add proper mutex guards as we should not be able to disable the core in the middle of enabling it. Note there's no need to rush in backporting this as the only user of the backend does not do anything crazy.. Fixes: 794ef0e5 ("iio: adc: adi-axi-adc: move to backend framework") Signed-off-by:
-
Dr. David Alan Gilbert authored
'adt7316_limit_regs' has never been used since the original commit 35f6b6b8 ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver"). The comment above it is a copy-and-paste from a different struct. Remove both the struct and the comment. Reviewed-by:
Dr. David Alan Gilbert <linux@treblig.org> Link: https://lore.kernel.org/r/20240529160055.28489-1-linux@treblig.orgSigned-off-by:
-
Antoniu Miclaus authored
The driver has no clock provider implementation, therefore remove the include. Fixes: 63aaf6d0 ("iio: frequency: adrf6780: add support for ADRF6780") Signed-off-by:
Antoniu Miclaus <antoniu.miclaus@analog.com> Link: https://lore.kernel.org/r/20240530092835.36892-1-antoniu.miclaus@analog.comSigned-off-by:
-
Denis Benato authored
bmi150-accel and bmi323-imu are declared in an almost identical way in the ACPI and in some devices such as the Asus RC71L the "ROTM" property can be found: parse and use the ACPI-defined mount-matrix. Co-developed-by:
Luke D. Jones <luke@ljones.dev> Co-developed-by:
Jonathan LoBue <jlobue10@gmail.com> Signed-off-by:
Denis Benato <benato.denis96@gmail.com> Link: https://lore.kernel.org/r/20240523174736.16692-2-benato.denis96@gmail.comSigned-off-by:
-
David Lechner authored
In the ad7944 driver, the ad7944_convert_and_acquire() had an unused `chan` parameter. This patch removes the parameter. Signed-off-by:
-
David Lechner authored
The Makefile for IIO ADC drivers is intended to be sorted alphabetically. I can be tricky to keep it sorted when adding new drivers when not all of the existing drivers are sorted. So let's sort everything now to make it easier to keep it sorted in the future. Signed-off-by:
-
Angelo Dureghello authored
Use same driver file name (ad3552r) for structure names used for all variants. Signed-off-by:
Angelo Dureghello <adureghello@baylibre.com> Reviewed-by:
-
Angelo Dureghello authored
After model data and num_hw_channles introduction, we have: ad3552r_desc, num_ch: used to keep channel number set in fdt, ad35xxr_model_data, num_hw_channels: for max channel checks, AD3552R_NUM_CH: just actually used to define the max array size on allocated arrays. Renaming AD3552R_NUM_CH to a more consistent name, as AD3552R_MAX_CH. Signed-off-by:
-
Angelo Dureghello authored
Add support for single-output DAC variants. Signed-off-by:
-
Angelo Dureghello authored
Add a "model data" structure to keep useful hardware-related information as from datasheet, avoiding id-based conditional choices later on. Removed id-based checks and filled model-specific structures with device specific features, In particular, num_hw_channels is introduced to keep the number of hardware implemented channels, since 1-channel versions of the DACs are added in this same patchset. Signed-off-by:
-
Angelo Dureghello authored
Add support for ad3541r and ad3551r single output variants. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Angelo Dureghello authored
The adi,gain-scaling-p/n values are an inverted log2, so initial naming was set correctly, but the driver uses just adi,gain-scaling-p/n, and if fdt is created accordingly with the fdt bindings documentation, driver fails the probe. Observing that: - the Linux driver is the only consumer, - there are no upstreamed dts nodes related to ad3552r, the fix to the documentation side is preferred and less-risk. Fixes: b0a96c5f ("dt-bindings: iio: dac: Add adi,ad3552r.yaml") Signed-off-by:
-
Nuno Sa authored
Using tabs and maintaining the start of the variables aligned is a pain and may lead to lot's of unrelated changes when adding new members. Hence, let's change things now and just have a simple space. Signed-off-by:
-
Nuno Sa authored
Make sure we use a DMA safe buffer (IIO_DMA_MINALIGN) for all the spi transfers. Only relevant for writes since for reads spi_write_then_read() is used which does not require DMA safe buffers. Also note that for consistency, ad9467_spi_read() is also taking struct ad9467_state as a parameter (even if not really needed). Fixes: ad679712 ("iio: adc: ad9467: add support AD9467 ADC") Signed-off-by:
-
Barnabás Czémán authored
Add support for more stk3311 variants like stk3311-a and stk3311-s34, they are register compatible but they have different chip ids. Signed-off-by:
Barnabás Czémán <trabarni@gmail.com> Link: https://lore.kernel.org/r/20240521-stk3311-v1-3-07a4966b355a@gmail.comSigned-off-by:
-
Barnabás Czémán authored
Modify chip id check for support easier additions for compatible variants. Signed-off-by:
-
Barnabás Czémán authored
Relax failure to match ID to a warning rather than probe fail. This add abilty to use other compatible variants when chip id is not defined in the driver. Signed-off-by:
-
Dr. David Alan Gilbert authored
'bu27034_result' is unused since the original commit e52afbd6 ("iio: light: ROHM BU27034 Ambient Light Sensor"). Remove it. Signed-off-by:
Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/20240522230457.478156-4-linux@treblig.orgSigned-off-by:
-
Dr. David Alan Gilbert authored
'samp_rate_mapping' has been unused since the original commit 0fb528c8 ("iio: adc: adding support for PAC193x"). Remove it. Signed-off-by:
-
Dr. David Alan Gilbert authored
'bmi088_scale_info' has been unused since the original commit c19ae6be ("iio: accel: Add support for the Bosch-Sensortec BMI088"). Remove it. Signed-off-by:
-
Alisa-Dariana Roman authored
Unlike the other AD719Xs, AD7194 has configurable channels. The user can dynamically configure them in the devicetree. Add sigma_delta_info member to chip_info structure. Since AD7194 is the only chip that has no channel sequencer, num_slots should remain undefined. Also modify config AD7192 description for better scaling. Signed-off-by:
Alisa-Dariana Roman <alisa.roman@analog.com> Link: https://lore.kernel.org/r/20240514120222.56488-7-alisa.roman@analog.comSigned-off-by:
-
Alisa-Dariana Roman authored
Unlike the other AD719Xs, AD7194 has configurable channels. The user can dynamically configure them in the devicetree. Also add an example for AD7194 devicetree. Signed-off-by:
-
Alisa-Dariana Roman authored
Devices that have both single-ended channels and differential channels cause a bit of confusion when the channels are configured in the devicetree. Clarify difference between these two types of channels for such devices by adding single-channel property alongside diff-channels. They should be mutually exclusive. Devices that have only single-ended channels can still use reg property to reference a channel like before. Suggested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Alisa-Dariana Roman authored
AINCOM should actually be a supply. AINx inputs are referenced to AINCOM in pseudo-differential operation mode. AINCOM voltage represents the offset of corresponding channels. Signed-off-by:
-
Alisa-Dariana Roman authored
AINCOM should actually be a supply. AINx inputs are referenced to AINCOM in pseudo-differential operation mode. AINCOM voltage represents the offset of corresponding channels. Reviewed-by:
Rob Herring (Arm) <robh@kernel.org> Signed-off-by:
-
Alisa-Dariana Roman authored
Replace custom attribute filter_low_pass_3db_frequency_available with standard attribute. Store the available values in ad7192_state struct. The function that used to compute those values replaced by ad7192_update_filter_freq_avail(). Function ad7192_show_filter_avail() is no longer needed. Note that the initial available values are hardcoded. Also moved the mutex lock and unlock in order to protect the whole switch statement since each branch modifies the state of the device. Reviewed-by:
-
- 27 May, 2024 7 commits
-
-
Vasileios Amoiridis authored
Introduce new linux/cleanup.h with the guard(mutex) functionality. Suggested-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Suggested-by:
Vasileios Amoiridis <vassilisamir@gmail.com> Link: https://lore.kernel.org/r/20240512230524.53990-3-vassilisamir@gmail.comSigned-off-by:
-
Vasileios Amoiridis authored
For BMP18x, BMP28x, BME280, BMP38x the reading of the pressure value requires an update of the t_fine variable which happens through reading the temperature value. So all the bmpxxx_read_press() functions of the above sensors are internally calling the equivalent bmpxxx_read_temp() function in order to update the t_fine value. By just looking at the code this functionality is a bit hidden and is not easy to understand why those channels are not independent. This commit tries to clear these things a bit by splitting the bmpxxx_{read/compensate}_{temp/press/humid}() to the following: i. bmpxxx_read_{temp/press/humid}_adc(): read the raw value from the sensor. ii. bmpxx_calc_t_fine(): calculate the t_fine variable. iii. bmpxxx_get_t_fine(): get the t_fine variable. iv. bmpxxx_compensate_{temp/press/humid}(): compensate the adc values and return the calculated value. v. bmpxxx_read_{temp/press/humid}(): combine calls of the aforementioned functions to return the requested value. Suggested-by: -
Vasileios Amoiridis authored
The raw sensor data that have not been compensated yet cannot be signed values, so use unsigned ones. Also, compensated pressure values cannot be negative so use unsigned also there. Also, drop redundant cast of data->t_fine variable from s32 to s32. Signed-off-by:
-
Vasileios Amoiridis authored
The form 'if (ret)' is used in this driver in order to check for returned error values. There are also some places that 'if (ret < 0)' is used but for no specific reason. Change them to 'if (ret)' to make the driver more consistent. Signed-off-by:
-
Vasileios Amoiridis authored
Remove duplicate error messages, add missing error messages and update redundant ones. Add one missing error check. Signed-off-by:
-
Vasileios Amoiridis authored
The ret value is being checked already in all the previous paths which exit in case of error, so this path can never become true. Signed-off-by:
-
Uwe Kleine-König authored
These drivers don't use the driver_data member of struct i2c_device_id, so don't explicitly initialize this member. This prepares putting driver_data in an anonymous union which requires either no initialization or named designators. But it's also a nice cleanup on its own. While add it, also remove commas after the sentinel entries. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20240508072928.2135858-2-u.kleine-koenig@pengutronix.deSigned-off-by:
-
