- 03 Apr, 2019 40 commits
-
-
Bjørn Mork authored
commit 84f3b43f upstream. This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Cc: stable@vger.kernel.org Signed-off-by:
Bjørn Mork <bjorn@mork.no> [ johan: use tabs to align comments in adjacent lines ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kristian Evensen authored
commit d1252f02 upstream. The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the same way as the EP06 (including the dynamic configuration behavior), so the same checks on reserved interfaces, etc. are needed. Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mans Rullgard authored
commit f8df5c2c upstream. The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4 of which are serial ports. The fifth is a network interface supported by the qmi-wwan driver. Furthermore, the serial ports do not support modem control signals. Add driver_info flags to reflect this. Signed-off-by:
Mans Rullgard <mans@mansr.com> Fixes: ec0cd94d ("usb: option: add SIMCom SIM5218") Cc: stable <stable@vger.kernel.org> # 3.2 Signed-off-by:
-
Lin Yi authored
commit 2908b076 upstream. The write_parport_reg_nonblock() helper takes a reference to the struct mos_parport, but failed to release it in a couple of error paths after allocation failures, leading to a memory leak. Johan said that move the kref_get() and mos_parport assignment to the end of urbtrack initialisation is a better way, so move it. and mos_parport do not used until urbtrack initialisation. Signed-off-by:
Lin Yi <teroincn@163.com> Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by:
-
George McCollister authored
commit 422c2537 upstream. Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be automatically detected. Signed-off-by:
George McCollister <george.mccollister@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit a595ecdd upstream. Lorenz Messtechnik has a device that is controlled by the cp210x driver, so add the device id to the driver. The device id was provided by Silicon-Labs for the devices from this vendor. Reported-by:
Uli <t9cpu@web.de> Signed-off-by:
-
Hoan Nguyen An authored
commit 93bcefd4 upstream. We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted (if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer, re-enable the SCSCR_TIE bit, which was done at sci_start_tx(). This is unnecessary processing, wasting CPU operation if the data transmission length is large. And further, transmit end, FIFO empty bits disabling have also been performed in the step above. Signed-off-by:
Hoan Nguyen An <na-hoan@jinso.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Aditya Pakki authored
commit 32f47179 upstream. of_match_device on failure to find a matching device can return a NULL pointer. The patch checks for such a scenrio and passes the error upstream. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Aditya Pakki authored
commit 3a10e3dd upstream. of_match_device can return a NULL pointer when matching device is not found. This patch avoids a scenario causing NULL pointer derefernce. Signed-off-by:
-
Chao Yu authored
commit 8bce6dce upstream. erofs_vmap() wrapped vmap() and vm_map_ram() to return virtual continuous memory, but both of them can failed due to a lot of reason, previously, erofs_vmap()'s callers didn't handle them, which can potentially cause NULL pointer access, fix it. Fixes: 3883a79a ("staging: erofs: introduce VLE decompression support") Fixes: 0d40d6e3 ("staging: erofs: add a generic z_erofs VLE decompressor") Cc: <stable@vger.kernel.org> # 4.19+ Signed-off-by:
Gao Xiang <gaoxiang25@huawei.com> Signed-off-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
-
Malcolm Priestley authored
commit 3b9c2f2e upstream. It appears on some slower systems that the driver can find its way out of the workqueue while the interrupt is disabled by continuous polling by it. Move MACvIntEnable to vnt_interrupt_work so that it is always enabled on all routes out of vnt_interrupt_process. Move MACvIntDisable so that the device doesn't keep polling the system while the workqueue is being processed. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> CC: stable@vger.kernel.org # v4.2+ Signed-off-by:
-
Malcolm Priestley authored
commit cc26358f upstream. A check for vif is made in vnt_interrupt_work. There is a small chance of leaving interrupt disabled while vif is NULL and the work hasn't been scheduled. Signed-off-by:
-
Samuel Thibault authored
commit 45ac7b31 upstream. When switching from speakup_soft to another synth, speakup_soft would keep calling synth_buffer_getc() from softsynthx_read. Let's thus make synth.c export the knowledge of the current synth, so that speakup_soft can determine whether it should be running. speakup_soft also needs to set itself alive, otherwise the switch would let it remain silent. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Ian Abbott authored
commit bafd9c64 upstream. `ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO subdevice (subdevice 2) of supported National Instruments M-series cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST` ioctls for this subdevice. There are two causes for a possible divide-by-zero error when validating that the `stop_arg` member of the passed-in command is not too large. The first cause for the divide-by-zero is that calls to `comedi_bytes_per_scan()` are only valid once the command has been copied to `s->async->cmd`, but that copy is only done for the `COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use whatever was left there by the previous `COMEDI_CMD` ioctl, if any. (This is very likely, as it is usual for the application to use `COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous, valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()` will return 0, so the subsequent division in `ni_cdio_cmdtest()` of `s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a divide-by-zero error. To fix this error, call a new function `comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing `comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for its calculations. (Also refactor `comedi_bytes_per_scan()` to call the new function.) Once the first cause for the divide-by-zero has been fixed, the second cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0. Fix it by only performing the division (and validating that `stop_arg` is no more than the maximum value) if `comedi_bytes_per_scan_cmd()` returns a non-zero value. The problem was reported on the COMEDI mailing list here: https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKMReported-by:
Ivan Vasilyev <grabesstimme@gmail.com> Tested-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Nathan Chancellor authored
commit c5cbc78a upstream. When building with -Wsometimes-uninitialized, Clang warns: drivers/tty/serial/qcom_geni_serial.c:1079:6: warning: variable 'baud' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] It's not wrong; when options is NULL, baud has no default value. Use 9600 as that is a sane default. Link: https://github.com/ClangBuiltLinux/linux/issues/395Suggested-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Kangjie Lu authored
commit c85be041 upstream. In case dmaengine_prep_dma_cyclic fails, the fix returns a proper error code to avoid NULL pointer dereference. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Fixes: 34df42f5 ("serial: at91: add rx dma support") Acked-by:
Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Kangjie Lu authored
commit 67343306 upstream. In case ioremap fails, the fix returns -ENOMEM to avoid NULL pointer dereferences. Multiple places use port.membase. Signed-off-by:
-
Jonas Karlman authored
commit e9abc611 upstream. NV12 framebuffers produced by the VPU shows distorted on RK3288 after win has been disabled when scaling is active. This issue can be reproduced using a 1080p modeset by: - Scale a 1280x720 NV12 framebuffer to 1920x1080 on win0 - Disable win0 - Display a 1920x1080 NV12 framebuffer without scaling on win0 - Output will now show the framebuffer distorted And by: - Scale a 1280x720 NV12 framebuffer to 1920x1080 - Change to a 720p modeset (win gets disabled and scaling reset to none) - Output will now show the framebuffer distorted Fix this by setting scale mode to none when win is disabled. Fixes: 4c156c21 ("drm/rockchip: vop: support plane scale") Cc: stable@vger.kernel.org Signed-off-by:
Jonas Karlman <jonas@kwiboo.se> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/AM3PR03MB0966DE3E19BACE07328CD637AC7D0@AM3PR03MB0966.eurprd03.prod.outlook.comSigned-off-by:
-
Steffen Maier authored
commit 242ec145 upstream. Suppose more than one non-NPIV FCP device is active on the same channel. Send I/O to storage and have some of the pending I/O run into a SCSI command timeout, e.g. due to bit errors on the fibre. Now the error situation stops. However, we saw FCP requests continue to timeout in the channel. The abort will be successful, but the subsequent TUR fails. Scsi_eh starts. The LUN reset fails. The target reset fails. The host reset only did an FCP device recovery. However, for non-NPIV FCP devices, this does not close and reopen ports on the SAN-side if other non-NPIV FCP device(s) share the same open ports. In order to resolve the continuing FCP request timeouts, we need to explicitly close and reopen ports on the SAN-side. This was missing since the beginning of zfcp in v2.6.0 history commit ea127f97 ("[PATCH] s390 (7/7): zfcp host adapter."). Note: The FSF requests for forced port reopen could run into FSF request timeouts due to other reasons. This would trigger an internal FCP device recovery. Pending forced port reopen recoveries would get dismissed. So some ports might not get fully reopened during this host reset handler. However, subsequent I/O would trigger the above described escalation and eventually all ports would be forced reopen to resolve any continuing FCP request timeouts due to earlier bit errors. Signed-off-by:
Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by:
Jens Remus <jremus@linux.ibm.com> Reviewed-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Steffen Maier authored
commit fe67888f upstream. An already deleted SCSI device can exist on the Scsi_Host and remain there because something still holds a reference. A new SCSI device with the same H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When we try to unblock an rport, we still find the deleted SCSI device and return early because the zfcp_scsi_dev of that SCSI device is not ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if the new proper SCSI device would be in good state. Therefore, skip deleted SCSI devices when iterating the sdevs of the shost. [cf. __scsi_device_lookup{_by_target}() or scsi_device_get()] The following abbreviated trace sequence can indicate such problem: Area : REC Tag : ersfs_3 LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED Ready count : n not incremented yet Running count : 0x00000000 ERP want : 0x01 ERP need : 0xc1 ZFCP_ERP_ACTION_NONE Area : REC Tag : ersfs_3 LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x41000000 Ready count : n+1 Running count : 0x00000000 ERP want : 0x01 ERP need : 0x01 ... Area : REC Level : 4 only with increased trace level Tag : ertru_l LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x40000000 Request ID : 0x0000000000000000 ERP status : 0x01800000 ERP step : 0x1000 ERP action : 0x01 ERP count : 0x00 NOT followed by a trace record with tag "scpaddy" for WWPN 0x50050763031bd327. Signed-off-by:
-
Martin K. Petersen authored
commit 1d5de5bd upstream. Commit a83da8a4 ("scsi: sd: Optimal I/O size should be a multiple of physical block size") split one conditional into several separate statements in an effort to provide more accurate warning messages when a device reports a nonsensical value. However, this reorganization accidentally dropped the precondition of the reported value being larger than zero. This lead to a warning getting emitted on devices that do not report an optimal I/O size at all. Remain silent if a device does not report an optimal I/O size. Fixes: a83da8a4 ("scsi: sd: Optimal I/O size should be a multiple of physical block size") Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Reported-by:
Hussam Al-Tayeb <ht990332@gmx.com> Tested-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Bart Van Assche authored
commit c14a5726 upstream. The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and hence needs the disk->private_data pointer. Avoid that that pointer is cleared before all affected I/O requests have finished. This patch avoids that the following crash occurs: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: scsi_mq_uninit_cmd+0x1c/0x30 scsi_end_request+0x7c/0x1b8 scsi_io_completion+0x464/0x668 scsi_finish_command+0xbc/0x160 scsi_eh_flush_done_q+0x10c/0x170 sas_scsi_recover_host+0x84c/0xa98 [libsas] scsi_error_handler+0x140/0x5b0 kthread+0x100/0x12c ret_from_fork+0x10/0x18 Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Jason Yan <yanaijie@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Jason Yan <yanaijie@huawei.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Darrick J. Wong authored
commit e6a9467e upstream. ocfs2_reflink_inodes_lock() can swap the inode1/inode2 variables so that we always grab cluster locks in order of increasing inode number. Unfortunately, we forget to swap the inode record buffer head pointers when we've done this, which leads to incorrect bookkeepping when we're trying to make the two inodes have the same refcount tree. This has the effect of causing filesystem shutdowns if you're trying to reflink data from inode 100 into inode 97, where inode 100 already has a refcount tree attached and inode 97 doesn't. The reflink code decides to copy the refcount tree pointer from 100 to 97, but uses inode 97's inode record to open the tree root (which it doesn't have) and blows up. This issue causes filesystem shutdowns and metadata corruption! Link: http://lkml.kernel.org/r/20190312214910.GK20533@magnolia Fixes: 29ac8e85 ("ocfs2: implement the VFS clone_range, copy_range, and dedupe_range features") Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Tetsuo Handa authored
commit 73601ea5 upstream. syzbot is hitting lockdep warning [1] due to trying to open a fifo during an execve() operation. But we don't need to open non regular files during an execve() operation, for all files which we will need are the executable file itself and the interpreter programs like /bin/sh and ld-linux.so.2 . Since the manpage for execve(2) says that execve() returns EACCES when the file or a script interpreter is not a regular file, and the manpage for uselib(2) says that uselib() can return EACCES, and we use FMODE_EXEC when opening for execve()/uselib(), we can bail out if a non regular file is requested with FMODE_EXEC set. Since this deadlock followed by khungtaskd warnings is trivially reproducible by a local unprivileged user, and syzbot's frequent crash due to this deadlock defers finding other bugs, let's workaround this deadlock until we get a chance to find a better solution. [1] https://syzkaller.appspot.com/bug?id=b5095bfec44ec84213bac54742a82483aad578ce Link: http://lkml.kernel.org/r/1552044017-7890-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpReported-by:
syzbot <syzbot+e93a80c1bb7c5c56e522461c149f8bf55eab1b2b@syzkaller.appspotmail.com> Fixes: 8924feff ("splice: lift pipe_lock out of splice_to_pipe()") Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by:
Kees Cook <keescook@chromium.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric Biggers <ebiggers3@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> [4.9+] Signed-off-by:
-
Fredrik Noring authored
commit 54a7151b upstream. Fix commit 56067812 ("kbuild: modversions: add infrastructure for emitting relative CRCs") where CRCs are interpreted in host byte order rather than proper kernel byte order. The bug is conditional on CONFIG_MODULE_REL_CRCS. For example, when loading a BE module into a BE kernel compiled with a LE system, the error "disagrees about version of symbol module_layout" is produced. A message such as "Found checksum D7FA6856 vs module 5668FAD7" will be given with debug enabled, which indicates an obvious endian problem within __kcrctab within the kernel image. The general solution is to use the macro TO_NATIVE, as is done in similar cases throughout modpost.c. With this correction it has been verified that a BE kernel compiled with a LE system accepts BE modules. This change has also been verified with a LE kernel compiled with a LE system, in which case TO_NATIVE returns its value unmodified since the byte orders match. This is by far the common case. Fixes: 56067812 ("kbuild: modversions: add infrastructure for emitting relative CRCs") Signed-off-by:
Fredrik Noring <noring@nocrew.org> Cc: stable@vger.kernel.org Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Bernhard Rosenkraenzer authored
commit e2a829b3 upstream. On an Acer Predator Helios 500 (Ryzen version), the laptop's speakers don't work out of the box. The problem can be worked around with hdajackretask, remapping the "Black Headphone, Right side" pin (0x21) to the Internal speaker. This patch adds a quirk to change this mapping by default. [ corrected ALC299_FIXUP_PREDATOR_SPK definition and adapted for the latest tree by tiwai ] Signed-off-by:
Bernhard Rosenkraenzer <bero@lindev.ch> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jian-Hong Pan authored
commit 6ac371aa upstream. The ASUS X430UN and X512DK with ALC256 cannot detect the headset MIC until ALC256_FIXUP_ASUS_MIC_NO_PRESENCE quirk applied. Signed-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by:
Daniel Drake <drake@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Chris Chiu authored
commit a806ef1c upstream. The ASUS laptop P5440FF with ALC256 can't detect the headset microphone until ALC256_FIXUP_ASUS_MIC_NO_PRESENCE quirk applied. Signed-off-by:
Chris Chiu <chiu@endlessm.com> Signed-off-by:
-
Jian-Hong Pan authored
commit e1037354 upstream. The ASUS laptop X441MB and X705FD with ALC256 cannot detect the headset MIC until ALC256_FIXUP_ASUS_MIC_NO_PRESENCE quirk applied. Signed-off-by:
-
Chris Chiu authored
commit c7531e31 upstream. The Acer laptop Aspire E5-523G and ES1-432 with ALC255 can't detect the headset microphone until ALC255_FIXUP_ACER_MIC_NO_PRESENCE quirk applied. Signed-off-by:
-
Jian-Hong Pan authored
commit 2733cceb upstream. The Acer Aspire Z24-890 cannot detect the headset MIC until ALC286_FIXUP_ACER_AIO_HEADSET_MIC quirk applied. Signed-off-by:
-
Jian-Hong Pan authored
commit 667a8f73 upstream. Some Acer AIO desktops like Veriton Z6860G, Z4860G and Z4660G cannot record sound from headset MIC. This patch adds the ALC286_FIXUP_ACER_AIO_HEADSET_MIC quirk to fix this issue. Fixes: 9f8aefed ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G") Fixes: b72f936f ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G") Signed-off-by:
Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Kailang Yang authored
commit da484d00 upstream. Enable headset mode support for new WYSE NB platform. Signed-off-by:
-
Kailang Yang authored
commit 136824ef upstream. This patch will enable WYSE AIO for Headset mode. Signed-off-by:
-
Takashi Iwai authored
commit 113ce081 upstream. Currently PCM core sets each opened stream forcibly to SUSPENDED state via snd_pcm_suspend_all() call, and the user-space is responsible for re-triggering the resume manually either via snd_pcm_resume() or prepare call. The scheme works fine usually, but there are corner cases where the stream can't be resumed by that call: the streams still in OPEN state before finishing hw_params. When they are suspended, user-space cannot perform resume or prepare because they haven't been set up yet. The only possible recovery is to re-open the device, which isn't nice at all. Similarly, when a stream is in DISCONNECTED state, it makes no sense to change it to SUSPENDED state. Ditto for in SETUP state; which you can re-prepare directly. So, this patch addresses these issues by filtering the PCM streams to be suspended by checking the PCM state. When a stream is in either OPEN, SETUP or DISCONNECTED as well as already SUSPENDED, the suspend action is skipped. To be noted, this problem was originally reported for the PCM runtime PM on HD-audio. And, the runtime PM problem itself was already addressed (although not intended) by the code refactoring commits 3d21ef0b ("ALSA: pcm: Suspend streams globally via device type PM ops") and 17bc4815 ("ALSA: pci: Remove superfluous snd_pcm_suspend*() calls"). These commits eliminated the snd_pcm_suspend*() calls from the runtime PM suspend callback code path, hence the racy OPEN state won't appear while runtime PM. (FWIW, the race window is between snd_pcm_open_substream() and the first power up in azx_pcm_open().) Although the runtime PM issue was already "fixed", the same problem is still present for the system PM, hence this patch is still needed. And for stable trees, this patch alone should suffice for fixing the runtime PM problem, too. Reported-and-tested-by:
Jon Hunter <jonathanh@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit ca0214ee upstream. The PCM OSS emulation converts and transfers the data on the fly via "plugins". The data is converted over the dynamically allocated buffer for each plugin, and recently syzkaller caught OOB in this flow. Although the bisection by syzbot pointed out to the commit 65766ee0 ("ALSA: oss: Use kvzalloc() for local buffer allocations"), this is merely a commit to replace vmalloc() with kvmalloc(), hence it can't be the cause. The further debug action revealed that this happens in the case where a slave PCM doesn't support only the stereo channels while the OSS stream is set up for a mono channel. Below is a brief explanation: At each OSS parameter change, the driver sets up the PCM hw_params again in snd_pcm_oss_change_params_lock(). This is also the place where plugins are created and local buffers are allocated. The problem is that the plugins are created before the final hw_params is determined. Namely, two snd_pcm_hw_param_near() calls for setting the period size and periods may influence on the final result of channels, rates, etc, too, while the current code has already created plugins beforehand with the premature values. So, the plugin believes that channels=1, while the actual I/O is with channels=2, which makes the driver reading/writing over the allocated buffer size. The fix is simply to move the plugin allocation code after the final hw_params call. Reported-by: syzbot+d4503ae45b65c5bc1194@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Gustavo A. R. Silva authored
commit c709f14f upstream. dev is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/core/seq/oss/seq_oss_synth.c:626 snd_seq_oss_synth_make_info() warn: potential spectre issue 'dp->synths' [w] (local cap) Fix this by sanitizing dev before using it to index dp->synths. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/ Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 2b1d9c8f upstream. info->stream is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/core/rawmidi.c:604 __snd_rawmidi_info_select() warn: potential spectre issue 'rmidi->streams' [r] (local cap) Fix this by sanitizing info->stream before using it to index rmidi->streams. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/ Cc: stable@vger.kernel.org Signed-off-by:
-
Christian Lamparter authored
commit 1eec7151 upstream. This belated patch implements Andrew Lunn's request of "remove the phy_read() and phy_write() functions." <https://lore.kernel.org/patchwork/comment/902734/> While seemingly harmless, this causes the switch's user port PHYs to get registered twice. This is because the DSA subsystem will create a slave mdio-bus not knowing that the qca8k_phy_(read|write) accessors operate on the external mdio-bus. So the same "bus" gets effectively duplicated. Cc: stable@vger.kernel.org Fixes: 6b93fb46 ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Olga Kornievskaia authored
commit 0cb98abb upstream. Allow the async rpc task for finish and update the open state if needed, then free the slot. Otherwise, the async rpc unable to decode the reply. Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Fixes: ae55e59d ("pnfs: Don't release the sequence slot...") Cc: stable@vger.kernel.org # v4.18+ Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by:
-
