Sridhar Samudrala says:

====================
Enable SW only or HW only offloads with u32 classifier

This set of patches export TCA_CLS_FLAGS_SKIP_HW to userspace and also
introduces another flag TCA_CLS_FLAGS_SKIP_SW. These flags enable offloading
u32 filters to either SW or HW only.

The default semantics with no flags is to add the filter to HW if possible and
also into SW.
With SKIP_HW flag, the filter is only added to SW.
With SKIP_SW flag, the filter is added to HW and an error is returned
to user on failure.
These flags are mutually exclusive.
There was an earlier discussion on these semantics in the following email
thread.
	http://thread.gmane.org/gmane.linux.network/401733
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On devices that support TC U32 offloads, this flag enables a filter to be
added only to HW. skip-sw and skip-hw are mutually exclusive flags. By
default without any flags, the filter is added to both HW and SW, but no
error checks are done in case of failure to add to HW. With skip-sw,
failure to add to HW is treated as an error.

Here is a sample script that adds 2 filters, one with skip-sw and the other
with skip-hw flag.

   # add ingress qdisc
   tc qdisc add dev p4p1 ingress

   # enable hw tc offload.
   ethtool -K p4p1 hw-tc-offload on

   # add u32 filter with skip-sw flag.
   tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
      handle 800:0:1 u32 ht 800: flowid 800:1 \
      skip-sw \
      match ip src 192.168.1.0/24 \
      action drop

   # add u32 filter with skip-hw flag.
   tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
      handle 800:0:2 u32 ht 800: flowid 800:2 \
      skip-hw \
      match ip src 192.168.2.0/24 \
      action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vitaly Kuznetsov says:

====================
hv_netvsc: avoid races on mtu change/set channels

Changes since v1:
- Rebased to net-next [Haiyang Zhang]

Original description:

MTU change and set channels operations are implemented as netvsc device
re-creation destroying internal structures (struct net_device stays). This
is really unfortunate but there is no support from Hyper-V host to do it
in a different way. Such re-creation is unsurprisingly racy, Haiyang
reported a crash when netvsc_change_mtu() is racing with
netvsc_link_change() but I was able to identify additional races upon
investigation. Both netvsc_set_channels() and netvsc_change_mtu() race
against:
1) netvsc_link_change()
2) netvsc_remove()
3) netvsc_send()

To solve these issues without introducing new locks some refactoring is
required. We need to get rid of very complex link graph in all the
internal structures and avoid traveling through structures which are being
removed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Crash in netvsc_send() is observed when netvsc device is re-created on
mtu change/set channels. The crash is caused by dereferencing of NULL
channel pointer which comes from chn_table. The root cause is a mixture
of two facts:
- we set nvdev pointer in net_device_context in alloc_net_device()
  before we populate chn_table.
- we populate chn_table[0] only.

The issue could be papered over by checking channel != NULL in
netvsc_send() but populating the whole chn_table and writing the
nvdev pointer afterwards seems more appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When netvsc device is removed during mtu change or channels setup we get
into troubles as both paths are trying to remove the device. Synchronize
them with start_remove flag and rtnl lock.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify netvsvc pointer graph by getting rid of the redundant ndev
pointer. We can always get a pointer to struct net_device from somewhere
else.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have the following structures keeping netvsc adapter state:
- struct net_device
- struct net_device_context
- struct netvsc_device
- struct rndis_device
- struct hv_device
and there are pointers/dependencies between them:
- struct net_device_context is contained in struct net_device
- struct hv_device has driver_data pointer which points to
  'struct net_device' OR 'struct netvsc_device' depending on driver's
  state (!).
- struct net_device_context has a pointer to 'struct hv_device'.
- struct netvsc_device has pointers to 'struct hv_device' and
  'struct net_device_context'.
- struct rndis_device has a pointer to 'struct netvsc_device'.

Different functions get different structures as parameters and use these
pointers for traveling. The problem is (in addition to keeping in mind
this complex graph) that some of these structures (struct netvsc_device
and struct rndis_device) are being removed and re-created on mtu change
(as we implement it as re-creation of hyper-v device) so our travel using
these pointers is dangerous.

Simplify this to a the following:
- add struct netvsc_device pointer to struct net_device_context (which is
  a part of struct net_device and thus never disappears)
- remove struct hv_device and struct net_device_context pointers from
  struct netvsc_device
- replace pointer to 'struct netvsc_device' with pointer to
  'struct net_device'.
- always keep 'struct net_device' in hv_device driver_data.

We'll end up with the following 'circular' structure:

net_device:
 [net_device_context] -> netvsc_device -> rndis_device -> net_device
                      -> hv_device -> net_device

On MTU change we'll be removing the 'netvsc_device -> rndis_device'
branch and re-creating it making the synchronization easier.

There is one additional redundant pointer left, it is struct net_device
link in struct netvsc_device, it is going to be removed in a separate
commit.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netvsc_link_change() can race with netvsc_change_mtu() or
netvsc_set_channels() as these functions destroy struct netvsc_device and
rndis filter. Use start_remove flag for syncronization. As
netvsc_change_mtu()/netvsc_set_channels() are called with rtnl lock held
we need to take it before checking start_remove value in
netvsc_link_change().
Reported-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct netvsc_device is destroyed on mtu change so keeping the
protection flag there is not a good idea. Move it to struct
net_device_context which is preserved.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The framework only asserts (for now) that the reset gpio is not active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-05-14

This series contains updates to i40e and i40evf.

Kevin adds support to disable link on all ports and changes bits set
for telling firmware the PHY needs to be modified by the driver.

Anjali adds a feature to enable/disable all multicast for a trusted
VF.  Added priv-flag knob to configure global true promiscuous
support.

Shannon adds the support code for calling the admin queue API call
aq_set_switch_config().

Mitch modifies the VF, to log a message if an untrusted VF attempts to
configure promiscuous mode, but lies to it and returns everything is ok
instead of returning an error.  Corrects the logic for reporting the
receive packet hash.  Fixed the adding of a broadcast filter for VFs,
since that all VSIs are configured to receive broadcasts as default,
so do not need to add a filter.

Catherine refactors the ethtool get_settings to report the possible
supported link modes from what we know about the current PHY type and
that with the firmware supported PHY types.

Jacob changes the driver to use WARN_ONCE in order to highlight the
issue, but do not display a warning every time when receive hang
message is received.

Akeem corrects receive ptype payload layer for non_tunneled IPv6, when
it should be layer 4 for UDP, instead of layer 3.

Dan Carpenter fixes an uninitialized variable bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: updates for net-next.

Non-critical bug fixes, improvements, a new ethtool feature, and a new
device ID.

v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.

Ajit Khaparde (2):
  bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO
  bnxt_en: Report PCIe link speed and width during driver load

Michael Chan (6):
  bnxt_en: Reduce maximum ring pages if page size is 64K.
  bnxt_en: Improve the delay logic for firmware response.
  bnxt_en: Fix length value in dmesg log firmware error message.
  bnxt_en: Simplify and improve unsupported SFP+ module reporting.
  bnxt_en: Add BCM57314 device ID.
  bnxt_en: Use dma_rmb() instead of rmb().

Satish Baddipadige (1):
  bnxt_en: Fix invalid max channel parameter in ethtool -l.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.

Rename bnxt_port_module_event() to bnxt_get_port_module_status().  We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status.  Delete
the unnecessary last_port_module_event.  Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The len value in the hwrm error message is wrong.  Use the properly adjusted
value in the variable len.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code has 2 problems:

1. The maximum wait time is not long enough.  It is about 60% of the
duration specified by the firmware.  It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.

2. The granularity of the delay is too coarse.  Many simple firmware
commands finish in 25 usec or less.

We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.

There is also a second delay loop to wait for the last DMA word to
complete.  This delay loop should be a very short 5 usec wait.

This change results in much faster bring-up/down time:

Before the patch:

time ip link set p4p1 up

real    0m0.120s
user    0m0.001s
sys     0m0.009s

After the patch:

time ip link set p4p1 up

real    0m0.030s
user    0m0.000s
sys     0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE.  The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large.  Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add code to log a message during driver load indicating PCIe link
speed and width.

The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command.  We support SFP+ and QSFP
modules.

v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l.  With only 1
vector, bnxt_get_max_rings() will return -ENOMEM.  bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.

The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.

Conflicts:
	drivers/net/wireless/intel/iwlwifi/mvm/tx.c
	net/ipv4/ip_gre.c
	net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix mvneta/bm dependencies, from Arnd Bergmann.

 2) RX completion hw bug workaround in bnxt_en, from Michael Chan.

 3) Kernel pointer leak in nf_conntrack, from Linus.

 4) Hoplimit route attribute limits not enforced properly, from Paolo
    Abeni.

 5) qlcnic driver NULL deref fix from Dan Carpenter.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  arm64: bpf: jit JMP_JSET_{X,K}
  net/route: enforce hoplimit max value
  nf_conntrack: avoid kernel pointer value leak in slab name
  drivers: net: xgene: fix register offset
  drivers: net: xgene: fix statistics counters race condition
  drivers: net: xgene: fix ununiform latency across queues
  drivers: net: xgene: fix sharing of irqs
  drivers: net: xgene: fix IPv4 forward crash
  xen-netback: fix extra_info handling in xenvif_tx_err()
  net: mvneta: bm: fix dependencies again
  bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)
  bnxt_en: Add workaround to detect bad opaque in rx completion (part 1)
  qlcnic: potential NULL dereference in qlcnic_83xx_get_minidump_template()

Switchdev has been around for quite a while now, putting "EXPERIMENTAL"
in the description is no longer accurate, drop it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Original implementation commit e54bcde3 ("arm64: eBPF JIT compiler")
had the relevant code paths, but due to an oversight always fail jiting.

As a result, we had been falling back to BPF interpreter whenever a BPF
program has JMP_JSET_{X,K} instructions.

With this fix, we confirm that the corresponding tests in lib/test_bpf
continue to pass, and also jited.

...
[    2.784553] test_bpf: #30 JSET jited:1 188 192 197 PASS
[    2.791373] test_bpf: #31 tcpdump port 22 jited:1 325 677 625 PASS
[    2.808800] test_bpf: #32 tcpdump complex jited:1 323 731 991 PASS
...
[    3.190759] test_bpf: #237 JMP_JSET_K: if (0x3 & 0x2) return 1 jited:1 110 PASS
[    3.192524] test_bpf: #238 JMP_JSET_K: if (0x3 & 0xffffffff) return 1 jited:1 98 PASS
[    3.211014] test_bpf: #249 JMP_JSET_X: if (0x3 & 0x2) return 1 jited:1 120 PASS
[    3.212973] test_bpf: #250 JMP_JSET_X: if (0x3 & 0xffffffff) return 1 jited:1 89 PASS
...

Fixes: e54bcde3 ("arm64: eBPF JIT compiler")
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.

The caller can i.e. set hoplimit to 256, and when such route will
 be used, packets will be sent with hoplimit/ttl equal to 0.

This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.

This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.

Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.

This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.

Fixes: 5b3501fa ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull vfs fixes from Al Viro:
 "Overlayfs fixes from Miklos, assorted fixes from me.

  Stable fodder of varying severity, all sat in -next for a while"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: ignore permissions on underlying lookup
  vfs: add lookup_hash() helper
  vfs: rename: check backing inode being equal
  vfs: add vfs_select_inode() helper
  get_rock_ridge_filename(): handle malformed NM entries
  ecryptfs: fix handling of directory opening
  atomic_open(): fix the handling of create_error
  fix the copy vs. map logics in blk_rq_map_user_iov()
  do_splice_to(): cap the size before passing to ->splice_read()

We removed this initialization but it is required.  Let's put it back.

Fixes: 895106a5 ('i40e: trivial fixes')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.

Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.

Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).

Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects Rx ptype payload layer for non_tunneled ipv6. It
should be layer 4 for UDP, instead of layer 3.

Change-ID: I9382e4458ab3c4e58f6d2e9f195d5d4ee513805e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use WARN_ONCE in order to highlight the issue, but don't display
a warning every time. The user should be able to see the ethtool counter
we created if necessary to see how often it is occurring.

Change-ID: I40c4ea159819b64a7d33b7f5716749089791533a
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.

Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.

Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.

The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.

For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.

Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP                    : off
LinkPolling            : off
flow-director-atr      : on
veb-stats              : off
hw-atr-eviction        : off
vf-true-promisc-support: off

to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on

At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic

Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the support code for calling the AdminQ API call aq_set_switch_config
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>