- 14 Sep, 2020 16 commits
-
-
Mauro Carvalho Chehab authored
Use 474 MHz frequency for DVB-T/DVB-C, as this is the at the channel range that it is valid on most places for DVB-T. In the case of DVB-S, let's add Astra 19.2E initial frequency at the scan files as the default, e. g. 12.5515 GHz. Signed-off-by:Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Mauro Carvalho Chehab authored
Right now, there are some issues at the tuning logic: 1) the config struct is not copied at the tuner driver. so, it won't use any frequency table at all; 2) the code that checks for frequency shifts is called at set_params. So, lock_status will never be zeroed; 3) the signal strength will also report a strong signal, even if not tuned; 4) the logic is not excluding non-set frequencies. Fix those issues. Signed-off-by: -
Mauro Carvalho Chehab authored
The two places where ENDIAN_BITFIELD is used is for a single 8-bits integer. No need to correct endiannes on such cases. Signed-off-by: -
Mauro Carvalho Chehab authored
Genmask is always highest order to low order. It doesn't make any sense to make it depends on endiannes. Signed-off-by: -
Mauro Carvalho Chehab authored
There are several warnings produced when the driver is built for 32-bit archs. Solve them. Reported-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
It is better to use the higher level dev_foo() than pr_foo() for printks. Change them at vidtv at the more trivial places. Signed-off-by: -
Mauro Carvalho Chehab authored
As this virtual driver is probed manually, add modaliases for this driver. Signed-off-by: -
Stanimir Varbanov authored
In order to boot some of the new Venus firmware versions TZ call to set virtual address ranges is needed. Add virtual address ranges for CP and CP_NONPIX in resource structure and use them when loading and booting the firmware on remote processor. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Stanimir Varbanov authored
This adds a new SCM memprotect command to set virtual address ranges. Signed-off-by:
Elliot Berman <eberman@codeaurora.org> Acked-by:
-
Stanimir Varbanov authored
We have a new helper to set profile and level use it instead. Signed-off-by:
-
Stanimir Varbanov authored
Currently the returned profile and level is not aligned with v4l2 ctrl id. Correct that by use the helpers which translate the v4l2 <-> hfi mapping internally. Signed-off-by:
-
Stanimir Varbanov authored
Get and set VP9 codec profile and levels. Signed-off-by:
-
Stanimir Varbanov authored
Introduce a helper to set and get profile and levels which includes the translation between v4l2 ctrl ids and HFI ids. The input arguments are always in v4l2 ids space. Signed-off-by:
-
Stanimir Varbanov authored
Add HFI defines for VP9 codec profile and levels. Signed-off-by:
-
Stanimir Varbanov authored
Add menu control for VP9 codec levels. A total of 14 levels are defined for Profile 0 (8bit) and Profile 2 (10bit). Each level is a set of constrained bitstreams coded with targeted resolutions, frame rates, and bitrates. The definitions have been taken from webm project [1]. [1] https://www.webmproject.org/vp9/levels/Signed-off-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Robin Murphy authored
Since commit 9495b7e9 ("driver core: platform: Initialize dma_parms for platform devices"), struct platform_device already provides a dma_parms structure, so we can save allocating another one. Also the DMA segment size is simply a size, not a bitmask. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
- 12 Sep, 2020 7 commits
-
-
Hans Verkuil authored
menuconfig DVB_TEST_DRIVERS should be added after the V4L_TEST_DRIVERS, otherwise there are no drivers listed in these two menus. Signed-off-by:
-
Mauro Carvalho Chehab authored
The current remove logic is broken and causes an OOPS. Fix it. Signed-off-by: -
Daniel W. S. Almeida authored
Add documentation for the Virtual Digital TV driver (vidtv) in the Restructured Text (ReST) format. This discusses: - What is vidtv - Why vidtv is needed - How to build and run vidtv - How vidtv is structured - How to test vidtv - How to improve vidtv [mchehab: fixed bad whitespaces] Signed-off-by:
Daniel W. S. Almeida <dwlsalmeida@gmail.com> Signed-off-by:
-
Daniel W. S. Almeida authored
Digital TV devices consist of several independent hardware components which are controlled by different drivers. Each media device is controlled by a group of cooperating drivers with the bridge driver as the main driver. This patch adds a bridge driver for the Virtual Digital TV driver [vidtv]. The bridge driver binds to the other drivers, that is, vidtv_tuner and vidtv_demod and implements the digital demux logic, providing userspace with a MPEG Transport Stream. The MPEG related code is split in the following way: - vidtv_ts: code to work with MPEG TS packets, such as TS headers, adaptation fields, PCR packets and NULL packets. - vidtv_psi: this is the PSI generator. PSI packets contain general information about a MPEG Transport Stream. A PSI generator is needed so userspace apps can retrieve information about the Transport Stream and eventually tune into a (dummy) channel. Because the generator is implemented in a separate file, it can be reused elsewhere in the media subsystem. Currently vidtv supports working with 3 PSI tables: PAT, PMT and SDT. - vidtv_pes: implements the PES logic to convert encoder data into MPEG TS packets. These can then be fed into a TS multiplexer and eventually into userspace. - vidtv_s302m: implements a S302M encoder to make it possible to insert PCM audio data in the generated MPEG Transport Stream. This shall enable passing an audio signal into userspace so it can be decoded and played by media software. - vidtv_channels: Implements a 'channel' abstraction When vidtv boots, it will create some hardcoded channels: Their services will be concatenated to populate the SDT. Their programs will be concatenated to populate the PAT For each program in the PAT, a PMT section will be created The PMT section for a channel will be assigned its streams. Every stream will have its corresponding encoder polled to produce TS packets These packets may be interleaved by the mux and then delivered to the bridge - vidtv_mux - Implements a MPEG TS mux, loosely based on the ffmpeg implementation The multiplexer is responsible for polling encoders, interleaving packets, padding the resulting stream with NULL packets if necessary and then delivering the resulting TS packets to the bridge driver so it can feed the demux. Signed-off-by:
-
Daniel W. S. Almeida authored
Implement a I2C demodulator driver, simulating support for DVB-T, DVB-C and DVB-S. This demodulator will periodically check the signal quality against a table and drop the TS lock if it drops below a threshold value, regaining it in the event that the signal improves. Signed-off-by:
-
Daniel W. S. Almeida authored
The virtual DVB test driver serves as a reference DVB driver and helps validate the existing APIs in the media subsystem. It can also aid developers working on userspace applications. This dummy tuner should support common TV standards such as DVB-T/T2/S/S2, ISDB-T and ATSC when completed. Signed-off-by:
-
Mauro Carvalho Chehab authored
It sounds that earlier versions of GCC have troubles when doing const math at compile time, if no typecast is used: on i386: ERROR: modpost: "__floatunsidf" [drivers/media/pci/ttpci/dvb-ttpci.ko] undefined! ERROR: modpost: "__ltdf2" [drivers/media/pci/ttpci/dvb-ttpci.ko] undefined! The warning was generated on gcc (SUSE Linux) 7.5.0. Gcc 9.2 compiles it fine. As an added bonus, it also fixes this objtool warning: drivers/media/pci/ttpci/av7110_v4l.c:163:11: error: SSE register return with SSE disabled Reported-by:
Randy Dunlap <rdunlap@infradead.org> Acked-by:
-
- 10 Sep, 2020 17 commits
-
-
Robert Foss authored
OV8856 supports 3264x2448 @ 30 FPS, which is added in this commit. Signed-off-by:
Robert Foss <robert.foss@linaro.org> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Robert Foss authored
OV8856 supports 1632x1224 @ 60 FPS, which is added in this commit. Signed-off-by:
-
Sakari Ailus authored
Document that it is possible to provide defaults for multiple bus types to v4l2_fwnode_endpoint_parse and v4l2_fwnode_endpoint_alloc_parse. Also underline the fact that detecting the bus type without bus-type property is only for the old drivers. Also correct capitalisation of BT.656. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Sakari Ailus authored
The bus specific parameters were a union. This made providing bus specific defaults impossible as the memory used to store the defaults for multiple different busses was the same. Make it struct instead. It's not large so the size isn't really an issue. Signed-off-by:
-
Sakari Ailus authored
The maximum is currently four (4). No short is needed. Signed-off-by:
-
Laurent Pinchart authored
v4l2_async_notifier_add_subdev() requires the asd to be allocated dynamically, but the max9286 driver embeds it in the max9286_source structure. This causes memory corruption when the notifier is destroyed at remove time with v4l2_async_notifier_cleanup(). Fix this issue by registering the asd with v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically internally. A new max9286_asd structure is introduced, to store a pointer to the corresonding max9286_source that needs to be accessed from bound and unbind callbacks. There's no need to take an extra explicit reference to the fwnode anymore as v4l2_async_notifier_add_fwnode_subdev() does so internally. While at it, use %u instead of %d to print the unsigned index in the error message from the v4l2_async_notifier_add_fwnode_subdev() error path. Fixes: 66d8c9d2 ("media: i2c: Add MAX9286 driver") Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
v4l2_async_notifier_add_subdev() requires the asd to be allocated dynamically, but the rcar-csi2 driver embeds it in the rcar_csi2 structure. This causes memory corruption when the notifier is destroyed at remove time with v4l2_async_notifier_cleanup(). Fix this issue by registering the asd with v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically internally. Fixes: 769afd21 ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver") Signed-off-by:
-
Laurent Pinchart authored
v4l2_async_notifier_add_subdev() requires the asd to be allocated dynamically, but the rcar-drif driver embeds it in the rcar_drif_graph_ep structure. This causes memory corruption when the notifier is destroyed at remove time with v4l2_async_notifier_cleanup(). Fix this issue by registering the asd with v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically internally. Fixes: d079f94c ("media: platform: Switch to v4l2_async_notifier_add_subdev") Signed-off-by:
-
Laurent Pinchart authored
The fwnode reference corresponding to the endpoint is leaked in an error path of the rcar_drif_parse_subdevs() function. Fix it, and reorganize fwnode reference handling in the function to release references early, simplifying error paths. Signed-off-by:
-
Laurent Pinchart authored
The v4l2_async_notifier_add_subdev() function requires the asd pointer it receives to be allocated dynamically, but doesn't explicitly say so. Only one driver out of 13 get its right (atmel-sama5d2-isc.c, but with memory leaks in the error paths), clearly showing we have an issue. Update the v4l2_async_notifier_add_subdev() documentation to clearly state the allocation requirement. Whether this will be enough to avoid new offending code isn't certain, but it's a good first step nonetheless. Fixes: 9ca46531 ("media: v4l: fwnode: Support generic parsing of graph endpoints in a device") Signed-off-by:
-
Lad Prabhakar authored
Fail probe if unsupported bus_type is detected. Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Lad Prabhakar authored
Enable support for BT656 mode. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
-
Lad Prabhakar authored
Configure HVP lines in s_power callback instead of configuring everytime in ov5640_set_stream_dvp(). Alongside also disable MIPI in DVP mode. Signed-off-by:
-
Lad Prabhakar authored
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP mode with rcar-vin bridge noticed the capture worked fine for the first run (with yavta), but for subsequent runs the bridge driver waited for the frame to be captured. Debugging further noticed the data lines were enabled/disabled in stream on/off callback and dumping the register contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct values, but yet frame capturing failed. To get around this issue data lines are enabled in s_power callback. (Also the sensor remains in power down mode if not streaming so power consumption shouldn't be affected) Fixes: f22996db ("media: ov5640: add support of DVP parallel interface") Signed-off-by:
-
Lad Prabhakar authored
In preparation for adding DVP configuration in s_power callback move mipi configuration into separate function Signed-off-by:
-
Lad Prabhakar authored
Keep the sensor in software power down mode and wake up only in ov5640_set_stream_dvp() callback. Signed-off-by:
-
Sakari Ailus authored
pr_info() was accidentally used to print the link frequencies whereas the rest of the information is printed on debug level. Fix that by using pr_debug() also for link frequencies. Signed-off-by:
-
