- 17 May, 2021 14 commits
-
-
Johannes Berg authored
Syzbot reports that in mac80211 we have a potential deadlock between our "local->stop_queue_reasons_lock" (spinlock) and netlink's nl_table_lock (rwlock). This is because there's at least one situation in which we might try to send a netlink message with this spinlock held while it is also possible to take the spinlock from a hardirq context, resulting in the following deadlock scenario reported by lockdep: CPU0 CPU1 ---- ---- lock(nl_table_lock); local_irq_disable(); lock(&local->queue_stop_reason_lock); lock(nl_table_lock); <Interrupt> lock(&local->queue_stop_reason_lock); This seems valid, we can take the queue_stop_reason_lock in any kind of context ("CPU0"), and call ieee80211_report_ack_skb() with the spinlock held and IRQs disabled ("CPU1") in some code path (ieee80211_do_stop() via ieee80211_free_txskb()). Short of disallowing netlink use in scenarios like these (which would be rather complex in mac80211's case due to the deep callchain), it seems the only fix for this is to disable IRQs while nl_table_lock is held to avoid hitting this scenario, this disallows the "CPU0" portion of the reported deadlock. Note that the writer side (netlink_table_grab()) already disables IRQs for this lock. Unfortunately though, this seems like a huge hammer, and maybe the whole netlink table locking should be reworked. Reported-by: syzbot+69ff9dff50dcfe14ddd4@syzkaller.appspotmail.com Signed-off-by:Johannes Berg <johannes.berg@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
If the device_add() for a smcd_dev fails, there's no cleanup step that rolls back the earlier list_add(). The device subsequently gets freed, and we end up with a corrupted list. Add some error handling that removes the device from the list. Fixes: c6ba7c9b ("net/smc: add base infrastructure for SMC-D and ISM") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Johannes Berg authored
If bond_kobj_init() or later kzalloc() in bond_alloc_slave() fail, then we call kobject_put() on the slave->kobj. This in turn calls the release function slave_kobj_release() which will always try to cancel_delayed_work_sync(&slave->notify_work), which shouldn't be done on an uninitialized work struct. Always initialize the work struct earlier to avoid problems here. Syzbot bisected this down to a completely pointless commit, some fault injection may have been at work here that caused the alloc failure in the first place, which may interact badly with bisect. Reported-by: syzbot+bfda097c12a00c8cae67@syzkaller.appspotmail.com Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The http://www.linuxfoundation.org/en/Net does not contain networking subsystem description ("Nothing found"). Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
Xin Long authored
On some host, a crash could be triggered simply by repeating these commands several times: # modprobe tipc # tipc bearer enable media udp name UDP1 localip 127.0.0.1 # rmmod tipc [] BUG: unable to handle kernel paging request at ffffffffc096bb00 [] Workqueue: events 0xffffffffc096bb00 [] Call Trace: [] ? process_one_work+0x1a7/0x360 [] ? worker_thread+0x30/0x390 [] ? create_worker+0x1a0/0x1a0 [] ? kthread+0x116/0x130 [] ? kthread_flush_work_fn+0x10/0x10 [] ? ret_from_fork+0x35/0x40 When removing the TIPC module, the UDP tunnel sock will be delayed to release in a work queue as sock_release() can't be done in rtnl_lock(). If the work queue is schedule to run after the TIPC module is removed, kernel will crash as the work queue function cleanup_beareri() code no longer exists when trying to invoke it. To fix it, this patch introduce a member wq_count in tipc_net to track the numbers of work queues in schedule, and wait and exit until all work queues are done in tipc_exit_net(). Fixes: d0f91938 ("tipc: add ip/udp media type") Reported-by:
Shuang Li <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Jon Maloy <jmaloy@redhat.com> Signed-off-by:
-
Taehee Yoo authored
mld_newpack() doesn't allow to allocate high order page, only order-0 allocation is allowed. If headroom size is too large, a kernel panic could occur in skb_put(). Test commands: ip netns del A ip netns del B ip netns add A ip netns add B ip link add veth0 type veth peer name veth1 ip link set veth0 netns A ip link set veth1 netns B ip netns exec A ip link set lo up ip netns exec A ip link set veth0 up ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0 ip netns exec B ip link set lo up ip netns exec B ip link set veth1 up ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1 for i in {1..99} do let A=$i-1 ip netns exec A ip link add ip6gre$i type ip6gre \ local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100 ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i ip netns exec A ip link set ip6gre$i up ip netns exec B ip link add ip6gre$i type ip6gre \ local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100 ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i ip netns exec B ip link set ip6gre$i up done Splat looks like: kernel BUG at net/core/skbuff.c:110! invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.12.0+ #891 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:skb_panic+0x15d/0x15f Code: 92 fe 4c 8b 4c 24 10 53 8b 4d 70 45 89 e0 48 c7 c7 00 ae 79 83 41 57 41 56 41 55 48 8b 54 24 a6 26 f9 ff <0f> 0b 48 8b 6c 24 20 89 34 24 e8 4a 4e 92 fe 8b 34 24 48 c7 c1 20 RSP: 0018:ffff88810091f820 EFLAGS: 00010282 RAX: 0000000000000089 RBX: ffff8881086e9000 RCX: 0000000000000000 RDX: 0000000000000089 RSI: 0000000000000008 RDI: ffffed1020123efb RBP: ffff888005f6eac0 R08: ffffed1022fc0031 R09: ffffed1022fc0031 R10: ffff888117e00187 R11: ffffed1022fc0030 R12: 0000000000000028 R13: ffff888008284eb0 R14: 0000000000000ed8 R15: 0000000000000ec0 FS: 0000000000000000(0000) GS:ffff888117c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8b801c5640 CR3: 0000000033c2c006 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600 ? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600 skb_put.cold.104+0x22/0x22 ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600 ? rcu_read_lock_sched_held+0x91/0xc0 mld_newpack+0x398/0x8f0 ? ip6_mc_hdr.isra.26.constprop.46+0x600/0x600 ? lock_contended+0xc40/0xc40 add_grhead.isra.33+0x280/0x380 add_grec+0x5ca/0xff0 ? mld_sendpack+0xf40/0xf40 ? lock_downgrade+0x690/0x690 mld_send_initial_cr.part.34+0xb9/0x180 ipv6_mc_dad_complete+0x15d/0x1b0 addrconf_dad_completed+0x8d2/0xbb0 ? lock_downgrade+0x690/0x690 ? addrconf_rs_timer+0x660/0x660 ? addrconf_dad_work+0x73c/0x10e0 addrconf_dad_work+0x73c/0x10e0 Allowing high order page allocation could fix this problem. Fixes: 72e09ad1 ("ipv6: avoid high order allocations") Signed-off-by:Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Zheyu Ma authored
'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a12987 #13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a12987 #13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100/0x480 [ 3.362175 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.362175 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.362175 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.362175 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.362175 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.362175 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.362175 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.362175 ] ? vprintk+0x76/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Dumping ftrace buffer: [ 3.362175 ] (ftrace buffer empty) [ 3.362175 ] Kernel Offset: disabled [ 3.362175 ] Rebooting in 1 seconds.. Reported-by:
Zheyu Ma <zheyuma97@gmail.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: 2 bug fixes. The first one fixes a bug to properly identify some recently added HyperV device IDs. The second one fixes device context memory set up on systems with 64K page size. Please queue these for -stable as well. Thanks. ==================== Signed-off-by: -
Michael Chan authored
There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in bnxt_hwrm_set_pg_attr(). Fix it and make the code more understandable with a new macro BNXT_SET_CTX_PAGE_ATTR(). Fixes: 1b9394e5 ("bnxt_en: Configure context memory on new devices.") Reviewed-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Andy Gospodarek authored
Otherwise, some of the recently added HyperV VF IDs would not be recognized as VF devices and they would not initialize properly. Fixes: 7fbf359b ("bnxt_en: Add PCI IDs for Hyper-V VF devices.") Reviewed-by:
Andy Gospodarek <gospo@broadcom.com> Signed-off-by:
-
Zhen Lei authored
Fix to return -EPERM from the error handling case instead of 0, as done elsewhere in this function. Fixes: b6016b76 ("[BNX2]: New Broadcom gigabit network driver.") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by:
-
Dongliang Mu authored
nfcmrvl_disconnect fails to free the hci_dev field in struct nci_dev. Fix this by freeing hci_dev in nci_free_device. BUG: memory leak unreferenced object 0xffff888111ea6800 (size 1024): comm "kworker/1:0", pid 19, jiffies 4294942308 (age 13.580s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 60 fd 0c 81 88 ff ff .........`...... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<000000004bc25d43>] kmalloc include/linux/slab.h:552 [inline] [<000000004bc25d43>] kzalloc include/linux/slab.h:682 [inline] [<000000004bc25d43>] nci_hci_allocate+0x21/0xd0 net/nfc/nci/hci.c:784 [<00000000c59cff92>] nci_allocate_device net/nfc/nci/core.c:1170 [inline] [<00000000c59cff92>] nci_allocate_device+0x10b/0x160 net/nfc/nci/core.c:1132 [<00000000006e0a8e>] nfcmrvl_nci_register_dev+0x10a/0x1c0 drivers/nfc/nfcmrvl/main.c:153 [<000000004da1b57e>] nfcmrvl_probe+0x223/0x290 drivers/nfc/nfcmrvl/usb.c:345 [<00000000d506aed9>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396 [<00000000bc632c92>] really_probe+0x159/0x4a0 drivers/base/dd.c:554 [<00000000f5009125>] driver_probe_device+0x84/0x100 drivers/base/dd.c:740 [<000000000ce658ca>] __device_attach_driver+0xee/0x110 drivers/base/dd.c:846 [<000000007067d05f>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:431 [<00000000f8e13372>] __device_attach+0x122/0x250 drivers/base/dd.c:914 [<000000009cf68860>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:491 [<00000000359c965a>] device_add+0x5be/0xc30 drivers/base/core.c:3109 [<00000000086e4bd3>] usb_set_configuration+0x9d9/0xb90 drivers/usb/core/message.c:2164 [<00000000ca036872>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238 [<00000000d40d36f6>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293 [<00000000bc632c92>] really_probe+0x159/0x4a0 drivers/base/dd.c:554 Reported-by: syzbot+19bcfc64a8df1318d1c3@syzkaller.appspotmail.com Fixes: 11f54f22 ("NFC: nci: Add HCI over NCI protocol support") Signed-off-by:Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by:
-
Dan Carpenter authored
In current kernels, small allocations never actually fail so this patch shouldn't affect runtime. Originally this error handling code written with the idea that if the "serial->tiocmget" allocation failed, then we would continue operating instead of bailing out early. But in later years we added an unchecked dereference on the next line. serial->tiocmget->serial_state_notification = kzalloc(); ^^^^^^^^^^^^^^^^^^ Since these allocations are never going fail in real life, this is mostly a philosophical debate, but I think bailing out early is the correct behavior that the user would want. And generally it's safer to bail as soon an error happens. Fixes: af0de130 ("usb: hso: obey DMA rules in tiocmget") Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Xin Long authored
It's not a good idea to append the frag skb to a skb's frag_list if the frag_list already has skbs from elsewhere, such as this skb was created by pskb_copy() where the frag_list was cloned (all the skbs in it were skb_get'ed) and shared by multiple skbs. However, the new appended frag skb should have been only seen by the current skb. Otherwise, it will cause use after free crashes as this appended frag skb are seen by multiple skbs but it only got skb_get called once. The same thing happens with a skb updated by pskb_may_pull() with a skb_cloned skb. Li Shuang has reported quite a few crashes caused by this when doing testing over macvlan devices: [] kernel BUG at net/core/skbuff.c:1970! [] Call Trace: [] skb_clone+0x4d/0xb0 [] macvlan_broadcast+0xd8/0x160 [macvlan] [] macvlan_process_broadcast+0x148/0x150 [macvlan] [] process_one_work+0x1a7/0x360 [] worker_thread+0x30/0x390 [] kernel BUG at mm/usercopy.c:102! [] Call Trace: [] __check_heap_object+0xd3/0x100 [] __check_object_size+0xff/0x16b [] simple_copy_to_iter+0x1c/0x30 [] __skb_datagram_iter+0x7d/0x310 [] __skb_datagram_iter+0x2a5/0x310 [] skb_copy_datagram_iter+0x3b/0x90 [] tipc_recvmsg+0x14a/0x3a0 [tipc] [] ____sys_recvmsg+0x91/0x150 [] ___sys_recvmsg+0x7b/0xc0 [] kernel BUG at mm/slub.c:305! [] Call Trace: [] <IRQ> [] kmem_cache_free+0x3ff/0x400 [] __netif_receive_skb_core+0x12c/0xc40 [] ? kmem_cache_alloc+0x12e/0x270 [] netif_receive_skb_internal+0x3d/0xb0 [] ? get_rx_page_info+0x8e/0xa0 [be2net] [] be_poll+0x6ef/0xd00 [be2net] [] ? irq_exit+0x4f/0x100 [] net_rx_action+0x149/0x3b0 ... This patch is to fix it by linearizing the head skb if it has frag_list set in tipc_buf_append(). Note that we choose to do this before calling skb_unshare(), as __skb_linearize() will avoid skb_copy(). Also, we can not just drop the frag_list either as the early time. Fixes: 45c8b7b1 ("tipc: allow non-linear first fragment buffer") Reported-by:
-
- 14 May, 2021 8 commits
-
-
Jonathan Davies authored
The old URL is no longer accessible. Signed-off-by:
Jonathan Davies <jonathan.davies@nutanix.com> Signed-off-by:
-
David S. Miller authored
Yunsheng Lin says: ==================== ix packet stuck problem for lockless qdisc This patchset fixes the packet stuck problem mentioned in [1]. Patch 1: Add STATE_MISSED flag to fix packet stuck problem. Patch 2: Fix a tx_action rescheduling problem after STATE_MISSED flag is added in patch 1. Patch 3: Fix the significantly higher CPU consumption problem when multiple threads are competing on a saturated outgoing device. V8: Change function name as suggested by Jakub and fix some typo in patch 3, adjust commit log in patch 2, and add Acked-by from Jakub. V7: Fix netif_tx_wake_queue() data race noted by Jakub. V6: Some performance optimization in patch 1 suggested by Jakub and drop NET_XMIT_DROP checking in patch 3. V5: add patch 3 to fix the problem reported by Michal Kubecek. V4: Change STATE_NEED_RESCHEDULE to STATE_MISSED and add patch 2. [1]. https://lkml.org/lkml/2019/10/9/42 ==================== Signed-off-by: -
Yunsheng Lin authored
The netdev qeueue might be stopped when byte queue limit has reached or tx hw ring is full, net_tx_action() may still be rescheduled if STATE_MISSED is set, which consumes unnecessary cpu without dequeuing and transmiting any skb because the netdev queue is stopped, see qdisc_run_end(). This patch fixes it by checking the netdev queue state before calling qdisc_run() and clearing STATE_MISSED if netdev queue is stopped during qdisc_run(), the net_tx_action() is rescheduled again when netdev qeueue is restarted, see netif_tx_wake_queue(). As there is time window between netif_xmit_frozen_or_stopped() checking and STATE_MISSED clearing, between which STATE_MISSED may set by net_tx_action() scheduled by netif_tx_wake_queue(), so set the STATE_MISSED again if netdev queue is restarted. Fixes: 6b3ba914 ("net: sched: allow qdiscs to handle locking") Reported-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
Currently qdisc_run() checks the STATE_DEACTIVATED of lockless qdisc before calling __qdisc_run(), which ultimately clear the STATE_MISSED when all the skb is dequeued. If STATE_DEACTIVATED is set before clearing STATE_MISSED, there may be rescheduling of net_tx_action() at the end of qdisc_run_end(), see below: CPU0(net_tx_atcion) CPU1(__dev_xmit_skb) CPU2(dev_deactivate) . . . . set STATE_MISSED . . __netif_schedule() . . . set STATE_DEACTIVATED . . qdisc_reset() . . . .<--------------- . synchronize_net() clear __QDISC_STATE_SCHED | . . . | . . . | . some_qdisc_is_busy() . | . return *false* . | . . test STATE_DEACTIVATED | . . __qdisc_run() *not* called | . . . | . . test STATE_MISS | . . __netif_schedule()--------| . . . . . . . . __qdisc_run() is not called by net_tx_atcion() in CPU0 because CPU2 has set STATE_DEACTIVATED flag during dev_deactivate(), and STATE_MISSED is only cleared in __qdisc_run(), __netif_schedule is called at the end of qdisc_run_end(), causing tx action rescheduling problem. qdisc_run() called by net_tx_action() runs in the softirq context, which should has the same semantic as the qdisc_run() called by __dev_xmit_skb() protected by rcu_read_lock_bh(). And there is a synchronize_net() between STATE_DEACTIVATED flag being set and qdisc_reset()/some_qdisc_is_busy in dev_deactivate(), we can safely bail out for the deactived lockless qdisc in net_tx_action(), and qdisc_reset() will reset all skb not dequeued yet. So add the rcu_read_lock() explicitly to protect the qdisc_run() and do the STATE_DEACTIVATED checking in net_tx_action() before calling qdisc_run_begin(). Another option is to do the checking in the qdisc_run_end(), but it will add unnecessary overhead for non-tx_action case, because __dev_queue_xmit() will not see qdisc with STATE_DEACTIVATED after synchronize_net(), the qdisc with STATE_DEACTIVATED can only be seen by net_tx_action() because of __netif_schedule(). The STATE_DEACTIVATED checking in qdisc_run() is to avoid race between net_tx_action() and qdisc_reset(), see: commit d518d2ed ("net/sched: fix race between deactivation and dequeue for NOLOCK qdisc"). As the bailout added above for deactived lockless qdisc in net_tx_action() provides better protection for the race without calling qdisc_run() at all, so remove the STATE_DEACTIVATED checking in qdisc_run(). After qdisc_reset(), there is no skb in qdisc to be dequeued, so clear the STATE_MISSED in dev_reset_queue() too. Fixes: 6b3ba914 ("net: sched: allow qdiscs to handle locking") Acked-by: -
Yunsheng Lin authored
Lockless qdisc has below concurrent problem: cpu0 cpu1 . . q->enqueue . . . qdisc_run_begin() . . . dequeue_skb() . . . sch_direct_xmit() . . . . q->enqueue . qdisc_run_begin() . return and do nothing . . qdisc_run_end() . cpu1 enqueue a skb without calling __qdisc_run() because cpu0 has not released the lock yet and spin_trylock() return false for cpu1 in qdisc_run_begin(), and cpu0 do not see the skb enqueued by cpu1 when calling dequeue_skb() because cpu1 may enqueue the skb after cpu0 calling dequeue_skb() and before cpu0 calling qdisc_run_end(). Lockless qdisc has below another concurrent problem when tx_action is involved: cpu0(serving tx_action) cpu1 cpu2 . . . . q->enqueue . . qdisc_run_begin() . . dequeue_skb() . . . q->enqueue . . . . sch_direct_xmit() . . . qdisc_run_begin() . . return and do nothing . . . clear __QDISC_STATE_SCHED . . qdisc_run_begin() . . return and do nothing . . . . . . qdisc_run_end() . This patch fixes the above data race by: 1. If the first spin_trylock() return false and STATE_MISSED is not set, set STATE_MISSED and retry another spin_trylock() in case other CPU may not see STATE_MISSED after it releases the lock. 2. reschedule if STATE_MISSED is set after the lock is released at the end of qdisc_run_end(). For tx_action case, STATE_MISSED is also set when cpu1 is at the end if qdisc_run_end(), so tx_action will be rescheduled again to dequeue the skb enqueued by cpu2. Clear STATE_MISSED before retrying a dequeuing when dequeuing returns NULL in order to reduce the overhead of the second spin_trylock() and __netif_schedule() calling. Also clear the STATE_MISSED before calling __netif_schedule() at the end of qdisc_run_end() to avoid doing another round of dequeuing in the pfifo_fast_dequeue(). The performance impact of this patch, tested using pktgen and dummy netdev with pfifo_fast qdisc attached: threads without+this_patch with+this_patch delta 1 2.61Mpps 2.60Mpps -0.3% 2 3.97Mpps 3.82Mpps -3.7% 4 5.62Mpps 5.59Mpps -0.5% 8 2.78Mpps 2.77Mpps -0.3% 16 2.22Mpps 2.22Mpps -0.0% Fixes: 6b3ba914 ("net: sched: allow qdiscs to handle locking") Acked-by:Juergen Gross <jgross@suse.com> Signed-off-by:
-
Jim Ma authored
In tls_sw_splice_read, checkout MSG_* is inappropriate, should use SPLICE_*, update tls_wait_data to accept nonblock arguments instead of flags for recvmsg and splice. Fixes: c46234eb ("tls: RX path for ktls") Signed-off-by:
Jim Ma <majinjing3@gmail.com> Signed-off-by:
-
Hoang Le authored
This reverts commit 6bf24dc0. Above fix is not correct and caused memory leak issue. Fixes: 6bf24dc0 ("net:tipc: Fix a double free in tipc_sk_mcast_rcv") Acked-by:
Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by:
Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Remove the flowtable hardware refresh state, fall back to the existing hardware pending state instead, from Roi Dayan. 2) Fix crash in pipapo avx2 lookup when FPU is in used from user context, from Stefano Brivio. ==================== Signed-off-by:
-
- 13 May, 2021 7 commits
-
-
Stefano Brivio authored
Arturo reported this backtrace: [709732.358791] WARNING: CPU: 3 PID: 456 at arch/x86/kernel/fpu/core.c:128 kernel_fpu_begin_mask+0xae/0xe0 [709732.358793] Modules linked in: binfmt_misc nft_nat nft_chain_nat nf_nat nft_counter nft_ct nf_tables nf_conntrack_netlink nfnetlink 8021q garp stp mrp llc vrf intel_rapl_msr intel_rapl_common skx_edac nfit libnvdimm ipmi_ssif x86_pkg_temp_thermal intel_powerclamp coretemp crc32_pclmul mgag200 ghash_clmulni_intel drm_kms_helper cec aesni_intel drm libaes crypto_simd cryptd glue_helper mei_me dell_smbios iTCO_wdt evdev intel_pmc_bxt iTCO_vendor_support dcdbas pcspkr rapl dell_wmi_descriptor wmi_bmof sg i2c_algo_bit watchdog mei acpi_ipmi ipmi_si button nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ipmi_devintf ipmi_msghandler ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 dm_mod raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor sd_mod t10_pi crc_t10dif crct10dif_generic raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod ahci libahci tg3 libata xhci_pci libphy xhci_hcd ptp usbcore crct10dif_pclmul crct10dif_common bnxt_en crc32c_intel scsi_mod [709732.358941] pps_core i2c_i801 lpc_ich i2c_smbus wmi usb_common [709732.358957] CPU: 3 PID: 456 Comm: jbd2/dm-0-8 Not tainted 5.10.0-0.bpo.5-amd64 #1 Debian 5.10.24-1~bpo10+1 [709732.358959] Hardware name: Dell Inc. PowerEdge R440/04JN2K, BIOS 2.9.3 09/23/2020 [709732.358964] RIP: 0010:kernel_fpu_begin_mask+0xae/0xe0 [709732.358969] Code: ae 54 24 04 83 e3 01 75 38 48 8b 44 24 08 65 48 33 04 25 28 00 00 00 75 33 48 83 c4 10 5b c3 65 8a 05 5e 21 5e 76 84 c0 74 92 <0f> 0b eb 8e f0 80 4f 01 40 48 81 c7 00 14 00 00 e8 dd fb ff ff eb [709732.358972] RSP: 0018:ffffbb9700304740 EFLAGS: 00010202 [709732.358976] RAX: 0000000000000001 RBX: 0000000000000003 RCX: 0000000000000001 [709732.358979] RDX: ffffbb9700304970 RSI: ffff922fe1952e00 RDI: 0000000000000003 [709732.358981] RBP: ffffbb9700304970 R08: ffff922fc868a600 R09: ffff922fc711e462 [709732.358984] R10: 000000000000005f R11: ffff922ff0b27180 R12: ffffbb9700304960 [709732.358987] R13: ffffbb9700304b08 R14: ffff922fc664b6c8 R15: ffff922fc664b660 [709732.358990] FS: 0000000000000000(0000) GS:ffff92371fec0000(0000) knlGS:0000000000000000 [709732.358993] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [709732.358996] CR2: 0000557a6655bdd0 CR3: 000000026020a001 CR4: 00000000007706e0 [709732.358999] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [709732.359001] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [709732.359003] PKRU: 55555554 [709732.359005] Call Trace: [709732.359009] <IRQ> [709732.359035] nft_pipapo_avx2_lookup+0x4c/0x1cba [nf_tables] [709732.359046] ? sched_clock+0x5/0x10 [709732.359054] ? sched_clock_cpu+0xc/0xb0 [709732.359061] ? record_times+0x16/0x80 [709732.359068] ? plist_add+0xc1/0x100 [709732.359073] ? psi_group_change+0x47/0x230 [709732.359079] ? skb_clone+0x4d/0xb0 [709732.359085] ? enqueue_task_rt+0x22b/0x310 [709732.359098] ? bnxt_start_xmit+0x1e8/0xaf0 [bnxt_en] [709732.359102] ? packet_rcv+0x40/0x4a0 [709732.359121] nft_lookup_eval+0x59/0x160 [nf_tables] [709732.359133] nft_do_chain+0x350/0x500 [nf_tables] [709732.359152] ? nft_lookup_eval+0x59/0x160 [nf_tables] [709732.359163] ? nft_do_chain+0x364/0x500 [nf_tables] [709732.359172] ? fib4_rule_action+0x6d/0x80 [709732.359178] ? fib_rules_lookup+0x107/0x250 [709732.359184] nft_nat_do_chain+0x8a/0xf2 [nft_chain_nat] [709732.359193] nf_nat_inet_fn+0xea/0x210 [nf_nat] [709732.359202] nf_nat_ipv4_out+0x14/0xa0 [nf_nat] [709732.359207] nf_hook_slow+0x44/0xc0 [709732.359214] ip_output+0xd2/0x100 [709732.359221] ? __ip_finish_output+0x210/0x210 [709732.359226] ip_forward+0x37d/0x4a0 [709732.359232] ? ip4_key_hashfn+0xb0/0xb0 [709732.359238] ip_sublist_rcv_finish+0x4f/0x60 [709732.359243] ip_sublist_rcv+0x196/0x220 [709732.359250] ? ip_rcv_finish_core.isra.22+0x400/0x400 [709732.359255] ip_list_rcv+0x137/0x160 [709732.359264] __netif_receive_skb_list_core+0x29b/0x2c0 [709732.359272] netif_receive_skb_list_internal+0x1a6/0x2d0 [709732.359280] gro_normal_list.part.156+0x19/0x40 [709732.359286] napi_complete_done+0x67/0x170 [709732.359298] bnxt_poll+0x105/0x190 [bnxt_en] [709732.359304] ? irqentry_exit+0x29/0x30 [709732.359309] ? asm_common_interrupt+0x1e/0x40 [709732.359315] net_rx_action+0x144/0x3c0 [709732.359322] __do_softirq+0xd5/0x29c [709732.359329] asm_call_irq_on_stack+0xf/0x20 [709732.359332] </IRQ> [709732.359339] do_softirq_own_stack+0x37/0x40 [709732.359346] irq_exit_rcu+0x9d/0xa0 [709732.359353] common_interrupt+0x78/0x130 [709732.359358] asm_common_interrupt+0x1e/0x40 [709732.359366] RIP: 0010:crc_41+0x0/0x1e [crc32c_intel] [709732.359370] Code: ff ff f2 4d 0f 38 f1 93 a8 fe ff ff f2 4c 0f 38 f1 81 b0 fe ff ff f2 4c 0f 38 f1 8a b0 fe ff ff f2 4d 0f 38 f1 93 b0 fe ff ff <f2> 4c 0f 38 f1 81 b8 fe ff ff f2 4c 0f 38 f1 8a b8 fe ff ff f2 4d [709732.359373] RSP: 0018:ffffbb97008dfcd0 EFLAGS: 00000246 [709732.359377] RAX: 000000000000002a RBX: 0000000000000400 RCX: ffff922fc591dd50 [709732.359379] RDX: ffff922fc591dea0 RSI: 0000000000000a14 RDI: ffffffffc00dddc0 [709732.359382] RBP: 0000000000001000 R08: 000000000342d8c3 R09: 0000000000000000 [709732.359384] R10: 0000000000000000 R11: ffff922fc591dff0 R12: ffffbb97008dfe58 [709732.359386] R13: 000000000000000a R14: ffff922fd2b91e80 R15: ffff922fef83fe38 [709732.359395] ? crc_43+0x1e/0x1e [crc32c_intel] [709732.359403] ? crc32c_pcl_intel_update+0x97/0xb0 [crc32c_intel] [709732.359419] ? jbd2_journal_commit_transaction+0xaec/0x1a30 [jbd2] [709732.359425] ? irq_exit_rcu+0x3e/0xa0 [709732.359447] ? kjournald2+0xbd/0x270 [jbd2] [709732.359454] ? finish_wait+0x80/0x80 [709732.359470] ? commit_timeout+0x10/0x10 [jbd2] [709732.359476] ? kthread+0x116/0x130 [709732.359481] ? kthread_park+0x80/0x80 [709732.359488] ? ret_from_fork+0x1f/0x30 [709732.359494] ---[ end trace 081a19978e5f09f5 ]--- that is, nft_pipapo_avx2_lookup() uses the FPU running from a softirq that interrupted a kthread, also using the FPU. That's exactly the reason why irq_fpu_usable() is there: use it, and if we can't use the FPU, fall back to the non-AVX2 version of the lookup operation, i.e. nft_pipapo_lookup(). Reported-by:
Arturo Borrero Gonzalez <arturo@netfilter.org> Cc: <stable@vger.kernel.org> # 5.6.x Fixes: 7400b063 ("nft_set_pipapo: Introduce AVX2-based lookup implementation") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Roi Dayan authored
Offloading conns could fail for multiple reasons and a hw refresh bit is set to try to reoffload it in next sw packet. But it could be in some cases and future points that the hw refresh bit is not set but a refresh could succeed. Remove the hw refresh bit and do offload refresh if requested. There won't be a new work entry if a work is already pending anyway as there is the hw pending bit. Fixes: 8b3646d6 ("net/sched: act_ct: Support refreshing the flow table entries") Signed-off-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
-
Tao Liu authored
We have observed meters working unexpected if traffic is 3+Gbit/s with multiple connections. now_ms is not pretected by meter->lock, we may get a negative long_delta_ms when another cpu updated meter->used, then: delta_ms = (u32)long_delta_ms; which will be a large value. band->bucket += delta_ms * band->rate; then we get a wrong band->bucket. OpenVswitch userspace datapath has fixed the same issue[1] some time ago, and we port the implementation to kernel datapath. [1] https://patchwork.ozlabs.org/project/openvswitch/patch/20191025114436.9746-1-i.maximets@ovn.org/ Fixes: 96fbc13d ("openvswitch: Add meter infrastructure") Signed-off-by:Tao Liu <thomas.liu@ucloud.cn> Suggested-by:
Ilya Maximets <i.maximets@ovn.org> Reviewed-by:
-
Wei Yongjun authored
In case of error, the function devm_platform_ioremap_resource_byname() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: b4cd249a ("net: korina: Use devres functions") Reported-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Ayush Sawal authored
This patch maintain the list of active tids and clear all the active connection resources when DETACH notification comes. Fixes: a8c16e8e ("crypto/chcr: move nic TLS functionality to drivers/net") Signed-off-by:
Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by:
-
Christophe JAILLET authored
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the probe function. So it must not be freed explicitly or there will be a double free. Remove the incorrect 'mdiobus_free' in the error handling path of the probe function and in remove function. Suggested-By:
Andrew Lunn <andrew@lunn.ch> Fixes: 35d2aeac ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
-
Christophe JAILLET authored
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the probe function. So it must not be freed explicitly or there will be a double free. Remove the incorrect 'mdiobus_free' in the remove function. Fixes: 379d7ac7 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Signed-off-by:
-
- 12 May, 2021 11 commits
-
-
Dan Carpenter authored
This error path needs to release some memory and call release_sock(sk); before returning. Fixes: 6919a826 ("Crypto/chtls: add/delete TLS header in driver") Signed-off-by:
-
Krzysztof Kozlowski authored
Keep all NFC related patches in existing linux-nfc@lists.01.org mailing list. Signed-off-by:
Mark Greer <mgreer@animalcreek.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The NFC subsystem is orphaned. I am happy to spend some cycles to review the patches, send pull requests and in general keep the NFC subsystem running. Signed-off-by:
-
Krzysztof Kozlowski authored
Emails to Clément Perrochaud bounce with permanent error "user does not exist", so remove Clément Perrochaud from NXP-NCI driver maintainers entry. Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.13-20210512' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-05-12 this is a pull request of a single patch for net/master. The patch is by Norbert Slusarek and it fixes a race condition in the CAN ISO-TP socket between isotp_bind() and isotp_setsockopt(). ==================== Signed-off-by:
-
Christophe JAILLET authored
If an error occurs after a successful 'pci_ioremap_bar()' call, it must be undone by a corresponding 'pci_iounmap()' call, as already done in the remove function. Fixes: a7e1abad ("ptp: Add clock driver for the OpenCompute TimeCard.") Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Dan Carpenter authored
This function is called from ethtool_set_rxfh() and "*rss_context" comes from the user. Add some bounds checking to prevent memory corruption. Fixes: 81a43620 ("octeontx2-pf: Add RSS multi group support") Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
-
David S. Miller authored
Joakim Zhang says: ==================== net: fixes for fec driver Two small fixes for fec driver. ==================== Signed-off-by: -
Fugang Duan authored
If MAC address read from nvmem efuse by calling .of_get_mac_address(), but nvmem efuse is registered later than the driver, then it return -EPROBE_DEFER value. So modify the driver to support defer probe when read MAC address from nvmem efuse. Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
-
Fugang Duan authored
If the memory allocated for cbd_base is failed, it should free the memory allocated for the queues, otherwise it causes memory leak. And if the memory allocated for the queues is failed, it can return error directly. Fixes: 59d0f746 ("net: fec: init multi queue date structure") Signed-off-by:
-
Richard Sanger authored
The packetmmap tx ring should only return timestamps if requested via setsockopt PACKET_TIMESTAMP, as documented. This allows compatibility with non-timestamp aware user-space code which checks tp_status == TP_STATUS_AVAILABLE; not expecting additional timestamp flags to be set in tp_status. Fixes: b9c32fb2 ("packet: if hw/sw ts enabled in rx/tx ring, report which ts we got") Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by:
Richard Sanger <rsanger@wand.net.nz> Signed-off-by:
-
