- 16 Jun, 2009 19 commits
-
-
David Brownell authored
Minor HNP bugfixes, so the initial role switch works: - A-Device: * disconnect-during-suspend enters A_PERIPHERAL state * kill OTG timer after reset as A_PERIPHERAL ... * ... and also pass that reset to the gadget * once HNP succeeds, clear the "ignore_disconnect" flag * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON - B-Device: * kill OTG timer on entry to B_HOST state (HNP succeeded) * once HNP succeeds, clear "ignore_disconnect" flag * kick the root hub only _after_ the state is adjusted Other state transitions are left alone. Notably, exit paths from the "roles have switched" state ... A_PERIPHERAL handling of that stays seriously broken. Signed-off-by:David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
David Brownell authored
Minor cleanup of OTG timer handling: * unify decls for OTG time constants, in the core header * set up and use that timer in a more normal way * move to the driver struct, so it's usable outside core And tighten use and setup of T(a_wait_bcon) so that if it's used, it's always valid. (If that timer expires, the A-device will stop powering VBUS. For non-OTG systems, that will be a surprise.) No behavioral changes, other than more consistency when applying that core HNP timeout. Signed-off-by: -
David Brownell authored
Let the otg_transceiver in MUSB be managed by an external driver; don't assume it's integrated. OMAP3 chips need it to be external, and there may be ways to interact with the transceiver which add functionality to the system. Platform init code is responsible for setting up the transeciver, probably using the NOP transceiver for integrated transceivers. External ones will use whatever the board init code provided, such as twl4030 or something more hands-off. Signed-off-by:
-
David Brownell authored
The NOP OTG transceiver driver needs to be usable from modules. Make sure its symbols are always accessible at both compile and link time, and make sure the device instance is allocated from the heap so that device lifetime rules are obeyed. Signed-off-by:
-
David Brownell authored
Fix a reporting glitch in the twl4030 USB transceiver code. It wasn't properly distinguishing the two types of active USB link: ID grounded, vs not. In the current code that distinction doesn't much matter; in the future this bugfix should help support better USB controller communications. Provide a comment sorting out some of the cryptic bits of the manual: different sections use different names for key signals, and the register definitions don't help much without the explanations and diagrams. Signed-off-by:
-
Uwe Kleine-König authored
A pointer to ehci_orion_drv_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Ronen Shitrit <rshitrit@marvell.com> Cc: Lennert Buytenhek <buytenh@marvell.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: Nicolas Pitre <nico@marvell.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Tzachi Perelstein <tzachi@marvell.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Uwe Kleine-König authored
A pointer to r8a66597_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by:
Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Cc: Magnus Damm <damm@igel.co.jp> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Uwe Kleine-König authored
A pointer to twl4030_usb_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by:
-
Sergei Shtylyov authored
As DaVinci DM646x has a dedicated CPPI DMA interrupt, replace cppi_completion() (which has always been kind of layering violation) by a complete CPPI interrupt handler. [ dbrownell@users.sourceforge.net: only cppi_dma.c needs platform device header, not cppi_dma.h ] Signed-off-by:
Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com> Signed-off-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Sergei Shtylyov authored
As musb_advance_schedule() is now the only remaning caller of musb_giveback() (and the only valid context of such call), just fold the latter into the former and then rename __musb_giveback() into musb_giveback(). This is a net minor shrink. Signed-off-by:
-
Sergei Shtylyov authored
The argument for the 'is_in' parameter of musb_cleanup_urb() is always extracted from an URB that's passed to the function. So that parameter is superfluous; remove it. Signed-off-by:
-
Sergei Shtylyov authored
The existance of the scheduling list shouldn't matter in determining whether there's currectly an URB executing on a hardware endpoint. What should actually matter is the 'in_qh' or 'out_qh' fields of the 'struct musb_hw_ep' -- those are set in musb_start_urb() and cleared in musb_giveback() when the endpoint's URB list drains. Hence we should be able to replace the big *switch* statements in musb_urb_dequeue() and musb_h_disable() with mere musb_ep_get_qh() calls... While at it, do some more changes: - add 'is_in' variable to musb_urb_dequeue(); - remove the unnecessary 'epnum' variable from musb_h_disable(); - fix the comment style in the vicinity. This is a minor shrink of source and object code. Signed-off-by:
-
Sergei Shtylyov authored
Factor out the often used code to get/set the active 'qh' pointer for the hardware endpoint. Change the way the case of a shared FIFO is handled by setting *both* 'in_qh' and 'out_qh' fields of 'struct musb_hw_ep'. That seems more consistent and makes getting to the current 'qh' easy when the code knows the direction beforehand. While at it, turn some assignments into intializers and fix declaration style in the vicinity. Signed-off-by:
-
Sergei Shtylyov authored
Refactor musb_save_toggle() as follows: - replace 'struct musb_hw_ep *ep' parameter by 'struct musb_qh *qh' to avoid re-calculating this value - move usb_settogle() call out of the *if* operator. This is a net minor shrink of source and object code. Signed-off-by:
-
Sergei Shtylyov authored
Suppress "parasitic" endpoint interrupts in the DMA mode when using CPPI DMA driver; they're caused by the MUSB gadget driver using the DMA request mode 0 instead of the mode 1. Signed-off-by:
-
Sergei Shtylyov authored
The gadget EP0 code routinely ignores an interrupt at end of the data phase because of musb_g_ep0_giveback() resetting the state machine to "idle, waiting for SETUP" phase prematurely. The driver also prematurely leaves the status phase on receiving the SetupEnd interrupt. As there were still unhandled endpoint 0 interrupts happening from time to time after fixing these issues, there turned to be yet another culprit: two distinct gadget states collapsed into one. The (missing) state that comes after STATUS IN/OUT states was typically indiscernible from them since the corresponding interrupts tend to happen within too little period of time (due to only a zero-length status packet in between) and so they got coalesced; yet this state is not the same as the next one which is associated with the reception of a SETUP packet. Adding this extra state seems to have fixed the rest of the unhandled interrupts that generic_interrupt() and davinci_interrupt() hid by faking their result and only emitting a debug message -- so, stop doing that. Signed-off-by:
-
Bryan Wu authored
Acked-by:
Mike Frysinger <vapier.adi@gmail.com> Signed-off-by:
-
Michele Valzelli authored
This patch adds support for the Toshiba HSDPA Minicard (which is just a rebranded Novatel EU870D) used in some Toshiba laptops. This is my first patch attempt, I hope I got the conventions right. Signed-off-by:
Michele Valzelli <valz@messagenet.it> Signed-off-by:
-
Daniel Suchy authored
I would like to have added new device to usbserial/ftdi_sio driver. These ids used USB track device (http://www.l-and-b.dk/access_alt.html). They use differend device IDs, but it works as standard usb-serial conventer. From: Daniel Suchy <danny@danysek.cz> Signed-off-by:
-
- 15 Jun, 2009 21 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] fix compile error in arch/ia64/mm/extable.c
-
Linus Torvalds authored
Merge branch 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: timers: Logic to move non pinned timers timers: /proc/sys sysctl hook to enable timer migration timers: Identifying the existing pinned timers timers: Framework for identifying pinned timers timers: allow deferrable timers for intervals tv2-tv5 to be deferred Fix up conflicts in kernel/sched.c and kernel/timer.c manually
-
Linus Torvalds authored
Merge branch 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: clockevent: export register_device and delta2ns clockevents: tick_broadcast_device can become static
-
Linus Torvalds authored
Merge branch 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: clocksource: prevent selection of low resolution clocksourse also for nohz=on clocksource: sanity check sysfs clocksource changes
-
Linus Torvalds authored
Merge branch 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: ntp: fix comment typos ntp: adjust SHIFT_PLL to improve NTP convergence
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1244 commits) pkt_sched: Rename PSCHED_US2NS and PSCHED_NS2US ipv4: Fix fib_trie rebalancing Bluetooth: Fix issue with uninitialized nsh.type in DTL-1 driver Bluetooth: Fix Kconfig issue with RFKILL integration PIM-SM: namespace changes ipv4: update ARPD help text net: use a deferred timer in rt_check_expire ieee802154: fix kconfig bool/tristate muckup bonding: initialization rework bonding: use is_zero_ether_addr bonding: network device names are case sensative bonding: elminate bad refcount code bonding: fix style issues bonding: fix destructor bonding: remove bonding read/write semaphore bonding: initialize before registration bonding: bond_create always called with default parameters x_tables: Convert printk to pr_err netfilter: conntrack: optional reliable conntrack event delivery list_nulls: add hlist_nulls_add_head and hlist_nulls_del ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits) powerpc: Fix bug in move of altivec code to vector.S powerpc: Add support for swiotlb on 32-bit powerpc/spufs: Remove unused error path powerpc: Fix warning when printing a resource_size_t powerpc/xmon: Remove unused variable in xmon.c powerpc/pseries: Fix warnings when printing resource_size_t powerpc: Shield code specific to 64-bit server processors powerpc: Separate PACA fields for server CPUs powerpc: Split exception handling out of head_64.S powerpc: Introduce CONFIG_PPC_BOOK3S powerpc: Move VMX and VSX asm code to vector.S powerpc: Set init_bootmem_done on NUMA platforms as well powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock powerpc/mm: Fix some SMP issues with MMU context handling powerpc: Add PTRACE_SINGLEBLOCK support fbdev: Add PLB support and cleanup DCR in xilinxfb driver. powerpc/virtex: Add ml510 reference design device tree powerpc/virtex: Add Xilinx ML510 reference design support powerpc/virtex: refactor intc driver and add support for i8259 cascading powerpc/virtex: Add support for Xilinx PCI host bridge ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: regulator/max1586: fix V3 gain calculation integer overflow regulator/max1586: support increased V3 voltage range regulator: lp3971 - fix driver link error when built-in. LP3971 PMIC regulator driver (updated and combined version) regulator: remove driver_data direct access of struct device regulator: Set MODULE_ALIAS for regulator drivers regulator: Support list_voltage for fixed voltage regulator regulator: Move regulator drivers to subsys_initcall() regulator: build fix for powerpc - renamed show_state regulator: add userspace-consumer driver Maxim 1586 regulator driver
-
Rusty Russell authored
ad6561df ("module: trim exception table on init free.") put a bogus trim_init_extable() function into ia64 which didn't compile. Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Tony Luck <tony.luck@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (22 commits) nilfs2: support contiguous lookup of blocks nilfs2: add sync_page method to page caches of meta data nilfs2: use device's backing_dev_info for btree node caches nilfs2: return EBUSY against delete request on snapshot nilfs2: modify list of unsupported features in caveats nilfs2: enable sync_page method nilfs2: set bio unplug flag for the last bio in segment nilfs2: allow future expansion of metadata read out via get info ioctl NILFS2: Pagecache usage optimization on NILFS2 nilfs2: remove nilfs_btree_operations from btree mapping nilfs2: remove nilfs_direct_operations from direct mapping nilfs2: remove bmap pointer operations nilfs2: remove useless b_low and b_high fields from nilfs_bmap struct nilfs2: remove pointless NULL check of bpop_commit_alloc_ptr function nilfs2: move get block functions in bmap.c into btree codes nilfs2: remove nilfs_bmap_delete_block nilfs2: remove nilfs_bmap_put_block nilfs2: remove header file for segment list operations nilfs2: eliminate removal list of segments nilfs2: add sufile function that can modify multiple segment usages ...
-
Philipp Zabel authored
On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote: > On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote: >> The V3 regulator can be configured with an external resistor >> connected to the feedback pin (R24 in the data sheet) to >> increase the voltage range. >> >> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum >> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency. >> >> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> > > Looks good. > > Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Thanks, but it turns out I hit a 32 bit integer overflow in the gain calculation. I'd like to mend that with the following patch. Now max_uV could be increased up to 4.294 V, enough to charge LiPo cells. Signed-off-by:
Philipp Zabel <philipp.zabel@gmail.com> Acked-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Liam Girdwood <lrg@slimlogic.co.uk>
-
Philipp Zabel authored
The V3 regulator can be configured with an external resistor connected to the feedback pin (R24 in the data sheet) to increase the voltage range. For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by:
-
Liam Girdwood authored
lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o Signed-off-by: -
Marek Szyprowski authored
This patch adds regulator drivers for National Semiconductors LP3971 PMIC. This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface. Reviewed-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Acked-by:
-
Greg Kroah-Hartman authored
In the near future, the driver core is going to not allow direct access to the driver_data pointer in struct device. Instead, the functions dev_get_drvdata() and dev_set_drvdata() should be used. These functions have been around since the beginning, so are backwards compatible with all older kernel versions. Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by:
-
Mark Brown authored
Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be auto loaded. Add the MODULE_ALIAS in case they do get built as modules. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
Regulators need to be available early in init in order to allow them to be available for consumers when requested. This is generally done by registering them at subsys_initcall() time but not all regulator drivers have done that. Convert these drivers to do so in order to mimimise future support. Signed-off-by:
Mike Rapoport <mike@compulab.co.il> Signed-off-by:
-
Liam Girdwood authored
This patch fixes the follwing build failure on powerpc:- > Today's linux-next build (powerpc allyesconfig) failed like this: > > drivers/regulator/userspace-consumer.c:43: error: conflicting types > for 'show_state' > include/linux/sched.h:273: note: previous definition of 'show_state' > was here > > Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator: > add userspace-consumer driver") which I have reverted for today. Signed-off-by: -
Mike Rapoport authored
The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by:
-
Robert Jarzmik authored
The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by:
-
