Common SHA-1 structures are defined in <crypto/sha.h> for code sharing.

This patch changes SHA-1/ARM glue code to use these structures.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The platforms selecting NEED_MACH_MEMORY_H defined the start address of
their physical memory in the respective <mach/memory.h>. With
ARM_PATCH_PHYS_VIRT=y (which is quite common today) this is useless
though because the definition isn't used but determined dynamically.

So remove the definitions from all <mach/memory.h> and provide the
Kconfig symbol PHYS_OFFSET with the respective defaults in case
ARM_PATCH_PHYS_VIRT isn't enabled.

This allows to drop the dependency of PHYS_OFFSET on !NEED_MACH_MEMORY_H
which prevents compiling an integrator nommu-kernel.
(CONFIG_PAGE_OFFSET which has "default PHYS_OFFSET if !MMU" expanded to
"0x" because CONFIG_PHYS_OFFSET doesn't exist as INTEGRATOR selects
NEED_MACH_MEMORY_H.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Broadcom Brahma-B15 (r0p0..r0p2) is also affected by Cortex-A15
erratum 798181, so enable the workaround for Brahma-B15.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Perform any CPU-specific initialization required on the
Broadcom Brahma-15 core.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

For LPAE, we have the following means for encoding writable or dirty
ptes:
                              L_PTE_DIRTY       L_PTE_RDONLY
    !pte_dirty && !pte_write        0               1
    !pte_dirty && pte_write         0               1
    pte_dirty && !pte_write         1               1
    pte_dirty && pte_write          1               0

So we can't distinguish between writeable clean ptes and read only
ptes. This can cause problems with ptes being incorrectly flagged as
read only when they are writeable but not dirty.

This patch renumbers L_PTE_RDONLY from AP[2] to a software bit #58,
and adds additional logic to set AP[2] whenever the pte is read only
or not dirty. That way we can distinguish between clean writeable ptes
and read only ptes.

HugeTLB pages will use this new logic automatically.

We need to add some logic to Transparent HugePages to ensure that they
correctly interpret the revised pgprot permissions (L_PTE_RDONLY has
moved and no longer matches PMD_SECT_AP2). In the process of revising
THP, the names of the PMD software bits have been prefixed with L_ to
make them easier to distinguish from their hardware bit counterparts.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Long descriptors on ARM are 64 bits, and some pte functions such as
pte_dirty return a bitwise-and of a flag with the pte value. If the
flag to be tested resides in the upper 32 bits of the pte, then we run
into the danger of the result being dropped if downcast.

For example:
	gather_stats(page, md, pte_dirty(*pte), 1);
where pte_dirty(*pte) is downcast to an int.

This patch introduces a new macro pte_isset which performs the bitwise
and, then performs a double logical invert (where needed) to ensure
predictable downcasting. The logical inverse pte_isclear is also
introduced.

Equivalent pmd functions for Transparent HugePages have also been
added.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The CP15 diagnostic register holds ARM errata bits on Cortex-A9, so it
needs to be saved/restored on suspend/resume.  Otherwise, the
effectiveness of errata workaround gets lost together with diagnostic
register bit across suspend/resume cycle.  And the CP15 power control
register of Cortex-A9 shares the same problem.

The patch adds a couple of Cortex-A9 specific suspend/resume functions
to save/restore these two Cortex-A9 CP15 registers across the
suspend/resume cycle.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch introduces a wfe-based polling loop for spinning on contended
MCS locks and waking up corresponding waiters when the lock is released.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Recent contributions, including to DRM and binder, introduce 64-bit
values in their interfaces. A common motivation for this is to allow
the same ABI for 32- and 64-bit userspaces (and therefore also a shared
ABI for 32/64 hybrid userspaces). Anyhow, the developers would like to
avoid gotchas like having to use copy_from_user().

This feature is already implemented on x86-32 and the majority of other
32-bit architectures. The current list of get_user_8 hold out
architectures are: arm, avr32, blackfin, m32r, metag, microblaze,
mn10300, sh.

Credit:

    My name sits rather uneasily at the top of this patch. The v1 and
    v2 versions of the patch were written by Rob Clark and to produce v4
    I mostly copied code from Russell King and H. Peter Anvin. However I
    have mangled the patch sufficiently that *blame* is rightfully mine
    even if credit should more widely shared.

Changelog:

v5: updated to use the ret macro (requested by Russell King)
v4: remove an inlined add on big endian systems (spotted by Russell King),
    used __ARMEB__ rather than BIG_ENDIAN (to match rest of file),
    cleared r3 on EFAULT during __get_user_8.
v3: fix a couple of checkpatch issues
v2: pass correct size to check_uaccess, and better handling of narrowing
    double word read with __get_user_xb() (Russell King's suggestion)
v1: original
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit cb8db5d4 (UAPI: (Scripted) Disintegrate arch/arm/include/asm) moved
these syscall comments out of their context into the UAPI headers. Fix this.

Fixes: cb8db5d4 ("UAPI: (Scripted) Disintegrate arch/arm/include/asm")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The section of the makefile that determines the TEXT_OFFSET is sorted
by address so that, in multi-arch kernel builds, the architecture with the
most stringent requirements for the kernel base address gets to define
TEXT_OFFSET. The comment should reflect that.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add revision info for PL310_ERRATA_588369 and PL310_ERRATA_727915 to
help people understand if they need to enable the errata for their
hardware.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Since pj4b suspend/resume routines are implemented based on generic
ARMv7 ones, instead of hard-coding cpu_pj4b_suspend_size, we should have
it be cpu_v7_suspend_size plus pj4b specific bytes.  Otherwise, if
cpu_v7_suspend_size gets updated alone, the pj4b suspend/resume will
likely be broken.

While at it, fix the comments in cpu_pj4b_do_resume, as we're restoring
CP15 registers rather than saving in there.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 78d7530a ("ARM: Clean up linker script using new linker script
macros.") modified the arm kernel linker script to use the STABS_DEBUG
macro, but left a .comment section definition. As STABS_DEBUG defines
the .comment section in an identical way, the second section definition
is redundant and can be removed.

This patch removes the redundant .comment section definition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use the newly introduced API so that FP is correctly referenced from
either R7/R11 based on whether we are running in THUMB2 mode or not.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Robert Richter <rric@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use the newly-introduced frame_pointer macro to extract
the correct FP based on whether we are in THUMB2 mode or not.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make the unwind code use the correct API so that the frame pointer
is extracted from the correct register.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make use of the arm_get_current_stackframe api so that
the frame pointer is correctly referenced in THUMB2 mode
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make the perf backend use the API so that it correctly references the FP
when in THUMB2 mode
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently there are numerous places where "struct pt_regs" are used to
populate "struct stackframe", however all of those location do not
consider the situation where the kernel might be compiled in THUMB2
mode, in which case the framepointer member of pt_regs become ARM_r7
instead of ARM_fp (r11). Document this idiosyncracy in the
definition of "struct stackframe"

The easiest solution is to introduce a new function (in the spirit of
https://groups.google.com/forum/#!topic/linux.kernel/dA2YuUcSpZ4)
which would hide the complexity of initializing the stackframe struct
from pt_regs.

Also implement a macro frame_pointer(regs) that would return the correct
register so that we can use it in cases where we just require the frame
pointer and not a whole struct stackframe
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Robert Richter <rric@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

With patch #8067/1 ("zImage: ensure header in LE format for BE8 kernels")
applied, it is no longer possible to determine the endianness of a compiled
kernel image.  This normally shouldn't matter to the boot environment,
except for those cases where the selection of a ramdisk or root filesystem
with a matching endianness has to be automated.

Let's add a flag to the zImage header indicating the actual endianness.
Four bytes from offset 0x30 can be interpreted as follows:

	04 03 02 01	big endian kernel

	01 02 03 04	little endian kernel

Anything else should be interpreted as "unknown", in which case it is
most likely that patch #8067/1 was not applied either and the zImage
magic number at offset 0x24 could be used instead to determine
endianness. No zImage before this patch ever produced 0x01020304 nor
0x04030201 at offset 0x30 so there is no confusion possible.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Save and report (via the procfs file) the last kernel unaligned fault
location.  This allows us to trivially inspect where the last fault
happened for cases which we don't expect to occur.

Since we expect the kernel to generate misalignment faults (due to
the networking layer), even when warnings are enabled, we don't log
them for the kernel.
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls.  Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).

We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.

Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code.  This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ensure that platform maintainers check the CPU part number in the right
manner: the CPU part number is meaningless without also checking the
CPU implement(e|o)r (choose your preferred spelling!)  Provide an
interface which returns both the implementer and part number together,
and update the definitions to include the implementer.

Mark the old function as being deprecated... indeed, using the old
function with the definitions will now always evaluate as false, so
people must update their un-merged code to the new function.  While
this could be avoided by adding new definitions, we'd also have to
create new names for them which would be awkward.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Building of EXYNOS5420_MCPM with disabled SUSPEND fails:
arch/arm/mach-exynos/built-in.o: In function `exynos_mcpm_init':
arch/arm/mach-exynos/mcpm-exynos.c:361: undefined reference to `mcpm_loopback'

The exynos_mcpm_init() in mcp-exynos.c calls mcpm_loopback() which
depends on cpu_suspend function (ARM_CPU_SUSPEND).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The Chromebook firmware doesn't enable the CCI for the boot cpu, and
arguably it shouldn't have to either. Let's have the kernel handle the

CCI on its own for the boot CPU the same way it does it for secondary CPUs
by using the MCPM loopback.

This allows to boot all 8 cores on exynos5420-peach-pit,
exynos5800-peach-pi and ARM Chromebook 2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is not strictly needed on TC2 but still a good idea to exercise
that code.
Signed-off-by: nicolas Pitre <nico@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The kernel already has the responsibility to handle resources such as the

CCI when hotplugging CPUs, during the booting of secondary CPUs, and when
resuming from suspend/idle.  It would be more coherent and less confusing
if the CCI for the boot CPU (or cluster)  was also initialized by the
kernel rather than expecting the firmware/bootloader to do it and only in
that case. After all, the kernel has all the necessary code already and
the bootloader shouldn't have to care at all.

The CCI may be turned on only when the cache is off. Leveraging the CPU
suspend code to loop back through the low-level MCPM entry point is all
that is needed to properly turn on the CCI from the kernel by using the
same code as during secondary boot.

Let's provide a generic MCPM loopback function that can be invoked by
backend initialization code to set things (CCI or similar) on the boot
CPU just as it is done for the other CPUs.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

After applying patch:
	"ARM: 8078/1: get rid of hardcoded assumptions about kernel stack size"

following build failure happens on iop13xx platform:

   In file included from include/linux/srcu.h:33:0,
                    from include/linux/notifier.h:15,
                    from include/linux/reboot.h:5,
                    from arch/arm/mach-iop13xx/include/mach/iop13xx.h:6,
                    from arch/arm/mach-iop13xx/include/mach/hardware.h:14,
                    from arch/arm/mach-iop13xx/include/mach/memory.h:4,
                    from arch/arm/include/asm/memory.h:24,
                    from arch/arm/include/asm/page.h:163,
                    from arch/arm/include/asm/thread_info.h:17,
                    from include/linux/thread_info.h:54,
                    from include/asm-generic/preempt.h:4,
                    from arch/arm/include/generated/asm/preempt.h:1,
                    from include/linux/preempt.h:18,
                    from include/linux/spinlock.h:50,
                    from include/linux/seqlock.h:35,
                    from include/linux/time.h:5,
                    from include/uapi/linux/timex.h:56,
                    from include/linux/timex.h:56,
                    from include/linux/sched.h:19,
                    from arch/arm/kernel/asm-offsets.c:13:
   include/linux/rcupdate.h: In function '__rcu_read_lock':
>> include/linux/rcupdate.h:220:2: error: implicit declaration of function 'preempt_disable' [-Werror=implicit-function-declaration]
     preempt_disable();

The problem here is recursive header inclusion which could be avoided by
removing linux/reboot.h from mach/iop13xxx.h.
linux/reboot.h in include/mach/iop13xx.h is needed only for enum reboot_mode,
so header it could be replaced with a enum declaration.

Whatever patch "ARM: 8078/1: get rid of hardcoded assumptions about kernel stack size"
does, I think it's good to avoid unnecessary header inclusion here in any case.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Changing kernel stack size on arm is not as simple as it should be:
1) THREAD_SIZE macro doesn't respect PAGE_SIZE and THREAD_SIZE_ORDER
2) stack size is hardcoded in get_thread_info macro

This patch fixes it by calculating THREAD_SIZE and thread_info address
taking into account PAGE_SIZE and THREAD_SIZE_ORDER.

Now changing stack size becomes simply changing THREAD_SIZE_ORDER.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As we are now using the C preprocessor, we do not need to use sed to
edit constants in this file, and then pass the resulting file through
the C preprocessor.  Instead, rely solely on the C preprocessor to
rewrite TEXT_START and BSS_ADDR.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

All known BE8-capable systems have LE bootloaders, so we need to ensure
that the magic number and image start/end values are in little endian
format.

[ben.dooks@codethink.co.uk: from nico's original email on this subject]
[taras.kondratiuk@linaro.org: removed lds.S->lds rule, added target to extra-y]
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The legacy OMAP DMA API is now deprecated; all remaining users should
now convert over ASAP to using the DMA engine API instead of the OMAP
private API.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull ARM fixes from Russell King:
 "Another round of ARM fixes.  The largest change here is the L2 changes
  to work around problems for the Armada 37x/380 devices, where most of
  the size comes down to comments rather than code.

  The other significant fix here is for the ptrace code, to ensure that
  rewritten syscalls work as intended.  This was pointed out by Kees
  Cook, but Will Deacon reworked the patch to be more elegant.

  The remainder are fairly trivial changes"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
  ARM: 8086/1: Set memblock limit for nommu
  ARM: 8085/1: sa1100: collie: add top boot mtd partition
  ARM: 8084/1: sa1100: collie: revert back to cfi_probe
  ARM: 8080/1: mcpm.h: remove unused variable declaration
  ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache

Note that I don't maintain Documentation/ABI/,
Documentation/devicetree/, or the language translation files.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These days most people use git to send patches so I have added a section
about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.

This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 1c2f87c2 (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>