Milo Kim's email in TI bounces with permanent error (550: Invalid
recipient).  Last email from him on LKML was in 2017.  Move Milo Kim to
credits and remove the separate driver entries for:
 - TI LP855x backlight driver,
 - TI LP8727 charger driver,
 - TI LP8788 MFD (ADC, LEDs, charger and regulator) drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds maintainer info for Intel MAX 10 mfd driver.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds access tables to the MAX 10 BMC regmap. This prevents
the host from accessing the unwanted I/O space. It also filters out the
invalid outputs when reading the regmap debugfs interface.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The version register is the only one in the legacy I/O space to be
accessed, so it is not necessary to define the legacy base & version
register offset. A direct definition of the legacy version register
address would be fine.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch fixes the max register address of MAX 10 BMC. The range
0x20000000 ~ 0x200000fc are for control registers of the QSPI flash
controller, which are not accessible to host.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fixes the following coccicheck warning:

  drivers/mfd/lm3533-core.c:361:60-61: WARNING opportunity for kobj_to_dev()
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Document the LP8756x-Q1 and LP87524-Q1 ICs reset pin.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds maintainer info for Intel MAX 10 mfd driver.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The sparse tool complains as follows:

drivers/mfd/ene-kb3930.c:36:15: warning: symbol 'kb3930_power_off' was not declared. Should it be static?

The symbol is not used outside of this file.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The ST-Ericsson U300 platform has been removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Nobody is passing the module parameter to disable the
battery management portions so just drop this parameter.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In stmpe_devices_init(), the start and end field of these structs are
modified, so they can not be const. Add a comment to those structs that
lacked it to reduce the risk that this happens again.

This reverts commit 8d7b3a6d.

Fixes: 8d7b3a6d ("mfd: stmpe: Constify static struct resource")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This define appears incorrect, but it is completely unused so it can be
removed.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The sparse tool complains as follows:

drivers/mfd/arizona-spi.c:28:31: warning:
 symbol 'reset_gpios' was not declared. Should it be static?
drivers/mfd/arizona-spi.c:29:31: warning:
 symbol 'ldoena_gpios' was not declared. Should it be static?

Those symbols are not used outside of arizona-spi.c, so this
commit marks them static.

Fixes: e9338367 ("mfd: arizona: Add support for ACPI enumeration of WM5102 connected over SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix the following coccicheck warning:

./include/linux/mfd/db8500-prcmu.h:723:8-9: WARNING: return of 0/1 in
function 'db8500_prcmu_is_ac_wake_requested' with return type bool.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the RN5T618 binding to DT schema format. Also
clearly state which regulators are available.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Immutable branch between MFD and Watchdog due for the v5.13 merge window

Merge tags 'ib-mfd-clk-gpio-regulator-rtc-v5.13', 'ib-mfd-extcon-v5.13', 'ib-mfd-input-v5.13-1', 'ib-mfd-platform-x86-v5.13', 'ib-mfd-power-v5.13', 'ib-mfd-pwm-rtc-v5.13-1' and 'ib-regulator-list-ramp-helpers-v5.13' into ibs-for-mfd-merged

Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window

Immutable branch between MFD and Extcon due for the v5.13 merge window

Immutable branch between MFD and Input due for the v5.13 merge window

Immutable branch between MFD and Platform/x86 due for the v5.13 merge window

Immutable branch between MFD and Power due for the v5.13 merge window

Immutable branch between MFD, PWM and RTC due for the v5.13 merge window

Add maintainer entries for ROHM BD71815AGW drivers.
New regulator and GPIO drivers were introduced for these PMICs.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

BD71815 contains similar RTC block as BD71828. Only the address offsets
seem different. Support also BD71815 RTC using rtc-bd70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

ROHM BD71815 also provide clk signal for RTC. Add control
for gating this clock.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Support voltage control for regulators on ROHM BD71815 PMIC.

ROHM BD71815 contains 5 bucks, 7 LDOs and a boost (intended for LED).
Bucks 1 and 2 support HW state based voltage level and enable states. Other
regulators support HW state based enable states. All bucks and LDOs 1-5
allow voltage changes for RUN state and LDO4 can be enabled/disabled via
GPIO.

LDO3 does support changing between two predetermined voltages by using
a GPIO but this functionality is not included in this commit.

This work is derived from driver originally written by Tony Luo
<luofc@embedinfo.com> - although not much of original work is left.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use generic regamp ramp-delay helper function instead of implementing own.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The ROHM BD71815 supports setting voltage levels/regulator status
for HW-states "RUN", "SUSPEND", "LPSR" and "SNVS". Add DT parsing
helper also for SNVS state.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The helper for obtaining HW-state based DVS voltage levels currently only
works for regulators using linear-ranges. Extend support to regulators with
simple linear mappings and add also proper error path if pickable-ranges
regulators call this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Support GPO(s) found from ROHM BD71815 power management IC. The IC has two
GPO pins but only one is properly documented in the data-sheet. The driver
exposes by default only the documented GPO. The second GPO is connected to
E5 pin and is marked as GND in the data-sheet. Control for this
undocumented pin can be enabled using a special DT property.

This driver is derived from work by Peter Yang <yanglsh@embest-tech.com>
although not so much of the original is left.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add core support for ROHM BD71815 Power Management IC.

The IC integrates regulators, a battery charger with a coulomb counter,
a real-time clock (RTC), clock gate and general-purpose outputs (GPO).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Sort the ID list so it is easier to see which ICs are present.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add chip ID for ROHM BD71815 and PMIC so that drivers can identify
this IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Document DT bindings for ROHM BD71815.

BD71815 is a single-chip power management IC mainly for battery-powered
portable devices. The IC integrates 5 bucks, 7 LDOs, a boost driver for
LED, a battery charger with a Coulomb counter, a real-time clock, a 32kHz
clock and two general-purpose outputs although only one is documented by
the data-sheet.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add binding documentation for regulators on ROHM BD71815 PMIC.
5 bucks, 7 LDOs and a boost for LED.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The BD71828 allows configuring the clk32kout pin mode to CMOS or
open-drain. Add device-tree property for specifying the preferred mode.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Most ROHM PMIC sub-devices only use the regmap pointer from
parent device. They can obtain this by dev_get_regamap so in
most cases the MFD device does not need to allocate and populate
the driver data. Simplify drivers by removing this.

The BD70528 still needs the access to watchdog mutex so keep
rohm_regmap_dev in use on BD70528 RTC and WDG drivers for now.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The ROHM BD71828 and BD71815 RTC drivers only need the regmap
pointer from parent. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.

BD70528 on the other hand requires parent data to access the
watchdog so leave the parent data for BD70528 here for now.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Quite a few regulator ICs do support setting ramp-delay by writing a value
matching the delay to a ramp-delay register.

Provide a simple helper for table-based delay setting.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/f101f1db564cf32cb58719c77af0b00d7236bb89.1617020713.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some drivers need to translate voltage values to selectors prior regulator
registration. Currently a regulator_desc based list_voltages helper is only
exported for regulators using the linear_ranges. Export similar helper also
for regulators using simple linear mapping.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/1200ef7a50c84327ada019b85f6527b4fc9b5ce1.1617020713.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is a slew of defines, structs and enums and even a
function call only relevant for the charging code that
still lives in <linux/mfd/abx500.h>. Push it down to the
"ab8500-bm.h" header in the power supply subsystem where
it is actually used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The charging algorithm header is only used locally in the
power supply subsystem so push this down into
drivers/power/supply and rename from the confusing
"ux500_chargalg.h" to "ab8500-chargalg.h" for clarity:
it is only used with the AB8500.

This is another remnant of non-DT code needing to pass
data from boardfiles, which we don't do anymore.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The global definition of platform data for the battery
management code has no utility after the OF conversion,
move the <linux/mfd/abx500/ab8500-bm.h> to be a local
file in drivers/power/supply and stop defining the
platform data in drivers/power/supply/ab8500_bmdata.c
and broadcast to the kernel only to have it assigned
as platform data to the MFD cells and then picked back
into the same subsystem that defined it in the first
place. This kills off a layer of indirection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>