- 27 Oct, 2022 26 commits
-
-
Moshe Shemesh authored
After firmware reset driver should verify firmware already enabled CRS and became responsive to pci config cycles before restoring pci state. Fix that by waiting till device_id is readable through PCI again. Fixes: eabe8e5e ("net/mlx5: Handle sync reset now event") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Hyong Youb Kim authored
An offloaded SA stops receiving after about 2^32 + replay_window packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all subsequent packets get dropped with SA-icv-failure (integrity_failed). To reproduce the bug: - ConnectX-6 Dx with crypto enabled (FW 22.30.1004) - ipsec.conf: nic-offload = yes replay-window = 32 esn = yes salifetime=24h - Run netperf for a long time to send more than 2^32 packets netperf -H <device-under-test> -t TCP_STREAM -l 20000 When 2^32 + replay_window packets are received, the replay window moves from the 2nd half of subspace (overlap=1) to the 1st half (overlap=0). The driver then updates the 'esn' value in NIC (i.e. seq_hi) as follows. seq_hi = xfrm_replay_seqhi(seq_bottom) new esn in NIC = seq_hi + 1 The +1 increment is wrong, as seq_hi already contains the correct seq_hi. For example, when seq_hi=1, the driver actually tells NIC to use seq_hi=2 (esn). This incorrect esn value causes all subsequent packets to fail integrity checks (SA-icv-failure). So, do not increment. Fixes: cb010083 ("net/mlx5: IPSec, Add support for ESN") Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com> Acked-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Zhengchao Shao says: ==================== fix some issues in netdevsim driver When strace tool is used to perform memory injection, memory leaks and files not removed issues are found. Fix them. ==================== Link: https://lore.kernel.org/r/20221026014642.116261-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Zhengchao Shao authored
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed. Otherwise, the netdevsim device will not be created next time. Kernel reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim' already present! Fixes: ab1d0cc0 ("netdevsim: change debugfs tree topology") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-
Zhengchao Shao authored
If some items in nsim_dev_resources_register() fail, memory leak will occur. The following is the memory leak information. unreferenced object 0xffff888074c02600 (size 128): comm "echo", pid 8159, jiffies 4294945184 (age 493.530s) hex dump (first 32 bytes): 40 47 ea 89 ff ff ff ff 01 00 00 00 00 00 00 00 @G.............. ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ backtrace: [<0000000011a31c98>] kmalloc_trace+0x22/0x60 [<0000000027384c69>] devl_resource_register+0x144/0x4e0 [<00000000a16db248>] nsim_drv_probe+0x37a/0x1260 [<000000007d1f448c>] really_probe+0x20b/0xb10 [<00000000c416848a>] __driver_probe_device+0x1b3/0x4a0 [<00000000077e0351>] driver_probe_device+0x49/0x140 [<0000000054f2465a>] __device_attach_driver+0x18c/0x2a0 [<000000008538f359>] bus_for_each_drv+0x151/0x1d0 [<0000000038e09747>] __device_attach+0x1c9/0x4e0 [<00000000dd86e533>] bus_probe_device+0x1d5/0x280 [<00000000839bea35>] device_add+0xae0/0x1cb0 [<000000009c2abf46>] new_device_store+0x3b6/0x5f0 [<00000000fb823d7f>] bus_attr_store+0x72/0xa0 [<000000007acc4295>] sysfs_kf_write+0x106/0x160 [<000000005f50cb4d>] kernfs_fop_write_iter+0x3a8/0x5a0 [<0000000075eb41bf>] vfs_write+0x8f0/0xc80 Fixes: 37923ed6 ("netdevsim: Add simple FIB resource controller via devlink") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-
Zhengchao Shao authored
If device_register() failed in nsim_bus_dev_new(), the value of reference in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be released. unreferenced object 0xffff88810352c480 (size 16): comm "echo", pid 5691, jiffies 4294945921 (age 133.270s) hex dump (first 16 bytes): 6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1...... backtrace: [<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0 [<0000000094ca4fc8>] kvasprintf+0xc3/0x160 [<00000000aad09bcc>] kvasprintf_const+0x55/0x180 [<000000009bac868d>] kobject_set_name_vargs+0x56/0x150 [<000000007c1a5d70>] dev_set_name+0xbb/0xf0 [<00000000ad0d126b>] device_add+0x1f8/0x1cb0 [<00000000c222ae24>] new_device_store+0x3b6/0x5e0 [<0000000043593421>] bus_attr_store+0x72/0xa0 [<00000000cbb1833a>] sysfs_kf_write+0x106/0x160 [<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0 [<00000000770b66e2>] vfs_write+0x8f0/0xc80 [<0000000078bb39be>] ksys_write+0x106/0x210 [<00000000005e55a4>] do_syscall_64+0x35/0x80 [<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 Fixes: 40e4fe4c ("netdevsim: move device registration and related code to bus.c") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221026015405.128795-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2022-10-27 Anssi Hannula fixes the use of the completions in the kvaser_usb driver. Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm that can be triggered by high CAN bus load and channel specific IRQ handlers are fixed. Yang Yingliang fixes the j1939 transport protocol by moving a kfree_skb() out of a spin_lock_irqsave protected section. * tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb() can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive can: kvaser_usb: Fix possible completions during init_completion ==================== Link: https://lore.kernel.org/r/20221027114356.1939821-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Rafał Miłecki authored
Queueing packets doesn't guarantee their transmission. Update TX stats after hardware confirms consuming submitted data. This also fixes a possible race and NULL dereference. bcm4908_enet_start_xmit() could try to access skb after freeing it in the bcm4908_enet_poll_tx(). Reported-by: Florian Fainelli <f.fainelli@gmail.com> Fixes: 4feffead ("net: broadcom: bcm4908enet: add BCM4908 controller driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Nicolas Dichtel says: ==================== ip: rework the fix for dflt addr selection for connected nexthop" This series reworks the fix that is reverted in the second commit. As Julian explained, nhc_scope is related to nhc_gw, it's not the scope of the route. ==================== Link: https://lore.kernel.org/r/20221020100952.8748-1-nicolas.dichtel@6wind.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Nicolas Dichtel authored
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but fib_info_update_nhc_saddr() needs the scope of the route, which is the scope "before" fib_nh_scope, ie fib_nh_scope - 1. This patch fixes the problem described in commit 747c1430 ("ip: fix dflt addr selection for connected nexthop"). Fixes: 597cfe4f ("nexthop: Add support for IPv4 nexthops") Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-
Nicolas Dichtel authored
This reverts commit 747c1430. As explained by Julian, nhc_scope is related to nhc_gw, not to the route. Revert the original patch. The initial problem is fixed differently in the next commit. Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-
Nicolas Dichtel authored
This reverts commit eb55dc09. The patch that introduces this bug is reverted right after this one. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
During review of previous change another thing came up - we should limit the use of validation workarounds to old commands. Don't list the workarounds one by one, as we're rejecting all existing ones. We can deal with the masking in the unlikely event that new flag is added. Link: https://lore.kernel.org/all/6ba9f727e555fd376623a298d5d305ad408c3d47.camel@sipsolutions.net/ Link: https://lore.kernel.org/r/20221026001524.1892202-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Florian Fainelli authored
Avoid the PHY library call unnecessarily into the suspend/resume functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT driver essentially does exactly what mdio_bus_phy_resume() does by calling phy_resume(). Fixes: fba863b8 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. The skb is unlinked from the queue, so it can be freed after spin_unlock_irqrestore(). Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com Cc: stable@vger.kernel.org [mkl: adjust subject] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Yang Yingliang authored
If of_device_register() returns error, the of node and the name allocated in dev_set_name() is leaked, call put_device() to give up the reference that was set in device_initialize(), so that of node is put in logical_port_release() and the name is freed in kobject_cleanup(). Fixes: 1acf2318 ("ehea: dynamic add / remove port") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>
-
Paolo Abeni authored
Aaron Conole says: ==================== openvswitch: syzbot splat fix and introduce selftest Syzbot recently caught a splat when dropping features from openvswitch datapaths that are in-use. The WARN() call is definitely too large a hammer for the situation, so change to pr_warn. Second patch in the series introduces a new selftest suite which can help show that an issue is fixed. This change might be more suited to net-next tree, so it has been separated out as an additional patch and can be either applied to either tree based on preference. ==================== Link: https://lore.kernel.org/r/20221025105018.466157-1-aconole@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>
-
Aaron Conole authored
Previous commit resolves a WARN splat that can be difficult to reproduce, but with the ovs-dpctl.py utility, it can be trivial. Introduce a test case which creates a DP, and then downgrades the feature set. This will include a utility 'ovs-dpctl.py' that can be extended to do additional tests and diagnostics. Signed-off-by: Aaron Conole <aconole@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-
Aaron Conole authored
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still preserve the warning to the user that feature downgrade occurred. We likely cannot introduce other kinds of checks / enforcement here because syzbot can generate different genl versions to the datapath. Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com Fixes: 44da5ae5 ("openvswitch: Drop user features if old user space attempted to create datapath") Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Aaron Conole <aconole@redhat.com> Acked-by: Ilya Maximets <i.maximets@ovn.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-
Marc Kleine-Budde authored
Biju Das <biju.das.jz@bp.renesas.com> says: This patch series fixes the below issues in R-Car CAN-FD driver. 1) Race condition in CAN driver under heavy CAN load condition with both channels enabled results in IRQ storm on global FIFO receive IRQ line. 2) Add channel specific TX interrupts handling for RZ/G2L SoC as it has separate IRQ lines for each TX. changes since v1: https://lore.kernel.org/all/20221022081503.1051257-1-biju.das.jz@bp.renesas.com * Added check for IRQ active and enabled before handling the IRQ on a particular channel. Link: https://lore.kernel.org/all/20221025155657.1426948-1-biju.das.jz@bp.renesas.com [mkl: adjust message, add link, take only patches 1 + 2, upstream 3 via can-next] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Biju Das authored
RZ/G2L has separate channel specific IRQs for transmit and error interrupts. But the IRQ handler processes both channels, even if there no interrupt occurred on one of the channels. This patch fixes the issue by passing a channel specific context parameter instead of global one for the IRQ register and the IRQ handler, it just handles the channel which is triggered the interrupt. Fixes: 76e9353a ("can: rcar_canfd: Add support for RZ/G2L family") Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org [mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Biju Das authored
We are seeing an IRQ storm on the global receive IRQ line under heavy CAN bus load conditions with both CAN channels enabled. Conditions: The global receive IRQ line is shared between can0 and can1, either of the channels can trigger interrupt while the other channel's IRQ line is disabled (RFIE). When global a receive IRQ interrupt occurs, we mask the interrupt in the IRQ handler. Clearing and unmasking of the interrupt is happening in rx_poll(). There is a race condition where rx_poll() unmasks the interrupt, but the next IRQ handler does not mask the IRQ due to NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and can1 is triggering RX interrupt, the delay in rx_poll() processing results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm. This patch fixes the issue by checking IRQ active and enabled before handling the IRQ on a particular channel. Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org [mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Anssi Hannula authored
kvaser_usb uses completions to signal when a response event is received for outgoing commands. However, it uses init_completion() to reinitialize the start_comp and stop_comp completions before sending the start/stop commands. In case the device sends the corresponding response just before the actual command is sent, complete() may be called concurrently with init_completion() which is not safe. This might be triggerable even with a properly functioning device by stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which also causes the driver to send CMD_STOP_CHIP when restart-ms is off), but that was not tested. Fix the issue by using reinit_completion() instead. Fixes: 080f40a6 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Tested-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Kunihiko Hayashi authored
The phylib callback is called after MAC driver's own resume callback is called. For AVE driver, after resuming immediately, PHY state machine is in PHY_NOLINK because there is a time lag from link-down to link-up due to autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume(). Since ave_resume() itself calls phy_resume(), AVE driver should manage PHY PM. To indicate that MAC driver manages PHY PM, set phydev->mac_managed_pm to true to avoid the unnecessary phylib call and add missing phy_init_hw() to ave_resume(). Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: fba863b8 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Juergen Borleis authored
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash: Unhandled fault: external abort on non-linefetch (0x1008) at […] due to this SoC has less registers in its FEC implementation compared to other i.MX6 variants. Thus, a run-time decision is required to avoid access to non-existing registers. Fixes: a51d3ab5 ("net: fec: use a more proper compatible string for i.MX6UL type device") Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2022-10-25 The 1st patch adds a missing cleanup call in the error path of the probe function in mpc5xxx glue code for the mscan driver. The 2nd patch adds a missing cleanup call in the error path of the probe function of the mcp251x driver. * tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path ==================== Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
- 26 Oct, 2022 5 commits
-
-
Rolf Eike Beer authored
The "random rhlist add/delete operations" actually wasn't very random, as all cases tested the same bit. Since the later parts of this loop depend on the first case execute this unconditionally, and then test on different bits for the remaining tests. While at it only request as much random bits as are actually used. Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Caleb Connolly authored
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was causing a harmless splat in ipa_idle_indication_cfg(), add a version check to prevent trying to fetch this register on v3.1 Fixes: 6a244b75 ("net: ipa: introduce ipa_reg()") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Tested-by: Jami Kettunen <jami.kettunen@somainline.org> Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Caleb Connolly authored
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask values, when the hardware actually uses 8. Out of range values were silently ignored before, so the IPA worked as expected. However the new generalised register definitions introduce stricter checking here, they now cause some splats and result in the value 0 being written instead. Fix the limit bitmask widths so that the correct values can be written. Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Tested-by: Jami Kettunen <jami.kettunen@somainline.org> Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Caleb Connolly authored
Some resource limits on IPA v3.5.1 have their max values set to 255, this causes a few splats in ipa_reg_encode and prevents the IPA from booting properly. The limits are all 6 bits wide so adjust the max values to 63. Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20221024210336.4014983-1-caleb.connolly@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Yang Yingliang authored
pci_disable_device() need be called while module exiting, switch to use pcim_enable(), pci_disable_device() will be called in pcim_release() while unbinding device. Fixes: 8ca86fd8 ("net: Micrel KSZ8841/2 PCI Ethernet driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
- 25 Oct, 2022 9 commits
-
-
Slawomir Laba authored
Fix setting bits for specific flow_type for GLQF_HASH_INSET register. In previous version all of the bits were set only in hena register, while in inset only one bit was set. In order for this working correctly on all types of cards these bits needs to be set correctly for both hena and inset registers. Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Sylwester Dziedziuch authored
When a reset was triggered on one VF with i40e_reset_vf global PF state __I40E_VF_DISABLE was set on a PF until the reset finished. If immediately after triggering reset on one VF there is a request to reset on another it will cause a hang on VF side because VF will be notified of incoming reset but the reset will never happen because of this global state, we will get such error message: [ +4.890195] iavf 0000:86:02.1: Never saw reset and VF will hang waiting for the reset to be triggered. Fix this by introducing new VF state I40E_VF_STATE_RESETTING that will be set on a VF if it is currently resetting instead of the global __I40E_VF_DISABLE PF state. Fixes: 3ba9bcb4 ("i40e: add locking around VF reset") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Slawomir Laba authored
When enabling flow type for RSS hash via ethtool: ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d the driver would fail to setup this setting on X722 device since it was using the mask on the register dedicated for X710 devices. Apply a different mask on the register when setting the RSS hash for the X722 device. When displaying the flow types enabled via ethtool: ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6 the driver would print wrong values for X722 device. Fix this issue by testing masks for X722 device in i40e_get_rss_hash_opts function. Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Eric Dumazet authored
Another syzbot report [1] with no reproducer hints at a bug in ip6_gre tunnel (dev:ip6gretap0) Since ipv6 mcast code makes sure to read dev->mtu once and applies a sanity check on it (see commit b9b312a7 "ipv6: mcast: better catch silly mtu values"), a remaining possibility is that a layer is able to set dev->mtu to an underflowed value (high order bit set). This could happen indeed in ip6gre_tnl_link_config_route(), ip6_tnl_link_config() and ipip6_tunnel_bind_dev() Make sure to sanitize mtu value in a local variable before it is written once on dev->mtu, as lockless readers could catch wrong temporary value. [1] skbuff: skb_over_panic: text:ffff80000b7a2f38 len:40 put:40 head:ffff000149dcf200 data:ffff000149dcf2b0 tail:0xd8 end:0xc0 dev:ip6gretap0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:120 Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 10241 Comm: kworker/1:1 Not tainted 6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022 Workqueue: mld mld_ifc_work pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : skb_panic+0x4c/0x50 net/core/skbuff.c:116 lr : skb_panic+0x4c/0x50 net/core/skbuff.c:116 sp : ffff800020dd3b60 x29: ffff800020dd3b70 x28: 0000000000000000 x27: ffff00010df2a800 x26: 00000000000000c0 x25: 00000000000000b0 x24: ffff000149dcf200 x23: 00000000000000c0 x22: 00000000000000d8 x21: ffff80000b7a2f38 x20: ffff00014c2f7800 x19: 0000000000000028 x18: 00000000000001a9 x17: 0000000000000000 x16: ffff80000db49158 x15: ffff000113bf1a80 x14: 0000000000000000 x13: 00000000ffffffff x12: ffff000113bf1a80 x11: ff808000081c0d5c x10: 0000000000000000 x9 : 73f125dc5c63ba00 x8 : 73f125dc5c63ba00 x7 : ffff800008161d1c x6 : 0000000000000000 x5 : 0000000000000080 x4 : 0000000000000001 x3 : 0000000000000000 x2 : ffff0001fefddcd0 x1 : 0000000100000000 x0 : 0000000000000089 Call trace: skb_panic+0x4c/0x50 net/core/skbuff.c:116 skb_over_panic net/core/skbuff.c:125 [inline] skb_put+0xd4/0xdc net/core/skbuff.c:2049 ip6_mc_hdr net/ipv6/mcast.c:1714 [inline] mld_newpack+0x14c/0x270 net/ipv6/mcast.c:1765 add_grhead net/ipv6/mcast.c:1851 [inline] add_grec+0xa20/0xae0 net/ipv6/mcast.c:1989 mld_send_cr+0x438/0x5a8 net/ipv6/mcast.c:2115 mld_ifc_work+0x38/0x290 net/ipv6/mcast.c:2653 process_one_work+0x2d8/0x504 kernel/workqueue.c:2289 worker_thread+0x340/0x610 kernel/workqueue.c:2436 kthread+0x12c/0x158 kernel/kthread.c:376 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860 Code: 91011400 aa0803e1 a90027ea 94373093 (d4210000) Fixes: c12b395a ("gre: Support GRE over IPv6") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20221024020124.3756833-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Benjamin Gaignard authored
RK3588(s) can have multiple gmac controllers. Re-use rk3568 logic to distinguish them. Fixes: 2f2b60a0 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>
-
Dongliang Mu authored
In mcp251x_can_probe(), if mcp251x_gpio_setup() fails, it forgets to unregister the CAN device. Fix this by unregistering can device in mcp251x_can_probe(). Fixes: 2d52dabb ("can: mcp251x: add GPIO support") Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/all/20221024090256.717236-1-dzm91@hust.edu.cn [mkl: adjust label] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Dongliang Mu authored
The commit 1149108e ("can: mscan: improve clock API use") only adds put_clock() in mpc5xxx_can_remove() function, forgetting to add put_clock() in the error handling code. Fix this bug by adding put_clock() in the error handling code. Fixes: 1149108e ("can: mscan: improve clock API use") Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/all/20221024133828.35881-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Jakub Kicinski authored
Merge tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== pull-request: ieee802154 for net 2022-10-24 Two fixup patches for return code changes of an earlier commit. Wei Yongjun fixed a missed -EINVAL return on the recent change, while Alexander Aring adds handling for unknown address type cases as well. Miquel Raynal fixed a long standing issue with LQI value recording which got broken 8 years ago. (It got more attention with the work in progress enhancement in wpan). * tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan: mac802154: Fix LQI recording net: ieee802154: fix error return code in dgram_bind() net: ieee802154: return -EINVAL for unknown addr type ==================== Link: https://lore.kernel.org/r/20221024102301.9433-1-stefan@datenfreihafen.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Fixes for 6.1 Patch 1 fixes an issue with assigning subflow IDs in cases where an incoming MP_JOIN is processed before accept() completes on the MPTCP socket. Patches 2 and 3 fix a deadlock issue with fastopen code (new for 6.1) at connection time. ==================== Link: https://lore.kernel.org/r/20221021225856.88119-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-