* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix smp barriers in test_and_{change,clear,set}_bit
  [MIPS] Fix IP27 build
  [MIPS] Fix modpost warnings by making start_secondary __cpuinit
  [MIPS] SMTC: Fix build error caused by nonsense code.
  [MIPS] SMTC: The MT ASE requires to initialize c0_pagemask and c0_wired.
  [MIPS] SMTC: Don't continue in set_vi_srs_handler on detected bad arguments.
  [MIPS] SMTC: Fix warning.
  [MIPS] Wire up utimensat, signalfd, timerfd, eventfd
  [MIPS] Atlas: Fix build.
  [MIPS] Always install the DSP exception handler.
  [MIPS] SMTC: Don't set and restore irqregs ptr from self_ipi.
  [MIPS] Fix KMODE for the R3000

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] CIFS should honour umask
  [CIFS] Missing flag on negprot needed for some servers to force packet signing
  [CIFS] whitespace cleanup part 2
  [CIFS] whitespace cleanup
  [CIFS] fix mempool destroy done in wrong order in cifs error path
  [CIFS] typo in previous patch
  [CIFS] Fix oops on failed cifs mount (in kthread_stop)

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] intel_agp: Add support for G33, Q33 and Q35 chipsets
  [AGPGART] intel_agp: add support for 945GME
  [AGPGART] intel_agp: add support for 965GME/GLE
  [AGPGART] intel_agp: use table for device probe
  [AGPGART] intel_agp: cleanup intel private data

* 'linus-plus-plus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: limit post SRST nsect/lbal wait to ~100ms
  libata: force PIO on IOMEGA ZIP 250 ATAPI
  libata passthru: update cached device paramters
  libata passthru: always enforce correct DEV bit
  libata passthru: map UDMA protocols
  libata passthru: support PIO multi commands
  libata passthru: update protocol numbers
  libata: Correct abuse of language
  libata-core/sff: Fix multiple assumptions about DMA
  ahci: Add MCP73/MCP77 support to AHCI driver
  libata: fix hw_sata_spd_limit initialization
  libata: print device model and firmware revision for ATAPI devices
  libata: fix probe time irq printouts
  libata: disable NCQ for HITACHI HTS541680J9SA00/SB21C7EP
  remove unused variable in pata_isapnp

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5751): Ivtv: fix ia64 printk format warnings.
  V4L/DVB (5761): Fix broken b2c2 dependency on non x86 architectures
  V4L/DVB (5673): Fix audio stuttering for saa711x/ivtv when in radio mode.
  V4L/DVB (5736): Add V4L2_FBUF_CAP/FLAG_LOCAL/GLOBAL_INV_ALPHA
  V4L/DVB (5732): Add ivtv CROPCAP support and fix ivtv S_CROP for video output.
  V4L/DVB (5730): Remove unused V4L2_CAP_VIDEO_OUTPUT_POS
  V4L/DVB (5720): Usbvision: fix urb allocation and submits
  V4L/DVB (5716): Tda10086,tda826x: fix tuning, STR/SNR values
  V4L/DVB (5675): Move big PIO accesses from the interrupt handler to a workhandler
  V4L/DVB (5699): Cinergyt2: fix file release handler
  V4L/DVB (5700): Saa7111: fix picture settings cache bug
  V4L/DVB (5702): Fix Kconfig items to avoid linkedition errors

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: Add the MCP73/77 support to PATA driver
  Add the PATA controller device ID to pci_ids.h for MCP73/MCP77.
  hpt366: disallow Ultra133 for HPT374
  ide: generic IDE PCI driver, add another device exception
  ide: HPA detect from resume
  it821x: RAID mode fixes
  serverworks: fix CSB6 tuning logic
  serverworks: remove crappy code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: don't call switch on old cards
  mmc: fix broken if clause
  au1xmmc: Replace C code with call to ARRAY_SIZE() macro.
  mmc-atmel: remove linux/mmc/protocol.h dependencies

* 'splice-2.6.22' of git://git.kernel.dk/data/git/linux-2.6-block:
  splice: __generic_file_splice_read: fix read/truncate race
  splice: __generic_file_splice_read: fix i_size_read() length checks
  splice: move balance_dirty_pages_ratelimited() outside of splice actor
  pipe: move pipe_inode_info structure decleration up before it's used
  splice: remove do_splice_direct() symbol export
  splice: move inode size check into generic_file_splice_read()

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

IP27 does no longer have ZONE_DMA.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

WARNING: arch/mips/kernel/built-in.o(.text+0x9a58): Section mismatch: reference to .init.text:cpu_report (between 'start_secondary' and 'smp_prepare_boot_cpu')
WARNING: arch/mips/kernel/built-in.o(.text+0x9a60): Section mismatch: reference to .init.text:per_cpu_trap_init (between 'start_secondary' and 'smp_prepare_boot_cpu')
WARNING: arch/mips/kernel/built-in.o(.text+0x9adc): Section mismatch: reference to .init.text:cpu_probe (between 'start_secondary' and 'smp_prepare_boot_cpu')
mipsel-linux-objcopy -S -O srec --remove-section=.reginfo --remove-section=.mdebug --remove-section=.comment --remove-section=.note --remove-section=.pdr --remove-section=.options --remove-section=.MIPS.options vmlinux arch/mips/boot/vmlinux.srec
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some non-DSP enabled cores 24K / 34K can generate a DSP exception where they
are actually expected to produce a reserved instruction exception.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This did corrupt register s0 which the caller of self_ipi expects to
be unchanged.  This is a kernel bug which will only be triggered with
the compilers which compile __smtc_ipi_replay to use s0 across the
invocation of self_ipi. Gcc 4.1.2 does this, for example.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 This must be the oldest bug that we have got.  Leaving interrupts "as
they are" for the R3000 obviously means copying IEp to IEc.  Since we have
got STATMASK now, I took this opportunity to mask the status register
"correctly" for the R3000 now too.  Oh, and the R3000 hardly ever is
64-bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

After SRST, libata used to wait for nsect/lbal to be set to 1/1 for
the slave device.  However, some ATAPI devices don't set nsect/lbal
after SRST and the wait itself isn't too useful as we're gonna wait
for !BSY right after that anyway.

Before reset-seq update, nsect/lbal wait failure used to be ignored
and caused 30sec delay during detection.  After reset-seq, all
timeouts are considered error conditions making libata fail to detect
such ATAPI devices.

This patch limits nsect/lbal wait to around 100ms.  This should give
acceptable behavior to such ATAPI devices while not disturbing the
heavily used code path too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

IOMEGA ZIP 250 ATAPI claims MWDMA0 support but fails SETXFERMODE if
asked to configure itself to MWDMA0.  Force PIO.

This fixes bugzilla bug#8497.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Calvin Walton <calvin.walton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata.  Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 Map the ATA passthru UDMA protocols to ATA_PROT_DMA.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

  support the pass through of PIO multi commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.

In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add the MCP73/MCP77 support to ahci driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

hw_sata_spd_limit used to be incorrectly initialized to zero instead
of UINT_MAX if SPD is zero in SControl register.  This breaks PHY
speed down.  Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

  For ATA/CFA devices, libata prints out the device model and firmware revision.
Do the same for ATAPI devices.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Most drivers don't seem to fill out the host->irq field, resulting in the
wrong (no) irq being reported at probe time. For example, sil24 on my system:

ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0

Since they're allocated and set up in ata_host_activate(), just save
them away there.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

HITACHI HTS541680J9SA00/SB21C7EP spuriously completes NCQ commands.
Blacklist it for NCQ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch has removed unused variable in pata_ispnp.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: Fix invalid assertion during write on 64k pages
  ocfs2: Fix masklog breakage

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [CIPSO]: Fix several unaligned kernel accesses in the CIPSO engine.
  [NetLabel]: consolidate the struct socket/sock handling to just struct sock
  [IPV4]: Do not remove idev when addresses are cleared

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Handle PCI bridges without 'ranges' property.
  [SPARC64]: Include <linux/rwsem.h> instead of <asm/rwsem.h>.

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  OHCI: Fix machine check in ohci_hub_status_data
  USB: Fix up bogus bInterval values in endpoint descriptors
  USB: cxacru: ignore error trying to start ADSL in atm_start
  USB: cxacru: create sysfs attributes in atm_start instead of bind
  USB: cxacru: add Documentation file
  USB: UNUSUAL_DEV: Sync up some reported devices from Ubuntu
  USB: usb gadgets avoid le{16,32}_to_cpup()
  usblp: Don't let suspend to kill ->used
  USB: set default y for CONFIG_USB_DEVICE_CLASS

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  firmware: remove orphaned Email
  kobject: use the proper printk level for kobject error
  Driver core: kill unused code
  Driver core: keep PHYSDEV for old struct class_device
  update Documentation/driver-model/platform.txt