- 17 Apr, 2023 20 commits
-
-
Ching-Te Ku authored
Correct Bluetooth RSSI count method. The 6dB is the gap between hardware packet sampled value and real RSSI value. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230412012831.10519-4-pkshih@realtek.com
-
Ching-Te Ku authored
Chips use similar hardware for path control, but could different path/antenna configuration. Add these register to monitor, if there are wrong settings, these register can help to debug. Signed-off-by:
-
Ching-Te Ku authored
When Wi-Fi & Bluetooth are both busy at the same time, Wi-Fi need to enable RX gain to protect Wi-Fi RX RF ability. Without this configure the interference from Bluetooth will bring a big impact to Wi-Fi RX. Signed-off-by:
-
Chih-Kang Chang authored
In WoWLAN Mode, it's expected that WiFi chip could enter power save mode only after all setting is finished, but current wow_enter_lps function break the rule and may lead to WoWLAN function fail in low probability, so fix it. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
To support WoWLAN mode for 8852be, we add one PLE quota setting and WoWLAN stub, which shows that supported WLAN events include receiving magic packet, rekey packet and deauth packet, and disconnecting from AP. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Golan Ben Ami authored
This is noising the kernel log and customers asked to hush it down. We can live with this message in "info" verbosity. Signed-off-by:
Golan Ben Ami <golan.ben.ami@intel.com> Signed-off-by:
Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230416154301.0a7f557aa2a0.If9db474b63242b1bfaed659aa174b678ae8dc196@changeidSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Emmanuel Grumbach authored
Since we didn't reset t to 0, only the first iteration of the loop did checked the ready bit several times. From the second iteration and on, we just tested the bit once and continued to the next iteration. Reported-and-tested-by:
Lorenzo Zolfanelli <lorenzo@zolfa.nl> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216452 Fixes: 289e5501 ("iwlwifi: fix the preparation of the card") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Johannes Berg authored
Newer firmware images have a TLV advertising how many beacons they support, use that to permit adding more links in AP mode (FW needs to support at least as many links as beacons). Signed-off-by:
-
Johannes Berg authored
Implement switching keys from one set of firmware station IDs to another set, during link switch. Signed-off-by:
-
Johannes Berg authored
When we switch station links, also add the code to switch BAIDs from one station mask to the new one. To do so, refactor the switching code a bit to have common code for all the needed switches; will add keys next. Signed-off-by:
-
Johannes Berg authored
When we have MLO connections, a BAID applies to multiple firmware stations. Track the station mask instead of the station ID, getting rid of a few more deflink cases and preparing for handling link switching for BAIDs. Signed-off-by:
-
Gregory Greenman authored
Start supporting API version 77 for AX devices. Signed-off-by:
-
Johannes Berg authored
When we remove a queue we need to use the currently active firmware stations in the mask, not the deflink one. Fix that. Signed-off-by:
-
Avraham Stern authored
The initiator smooth list is initialized only in iwl_mvm_up(), but is cleared in iwl_mvm_mac_stop. This may result in iterating over the list before it was initialized in case iwl_mvm_up() failed early. Fix it by moving the list initialization to an earlier stage. Fixes: b68bd2e3 ("iwlwifi: mvm: Add FTM initiator RTT smoothing logic") Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
-
Johannes Berg authored
We are going to need this in more places than just the key code, so factor out the functionality of getting the FW station ID mask (filtered to a specific link if needed) to a separate function that can now be called both under RCU and mvm->mutex protection. Signed-off-by:
-
Johannes Berg authored
The firmware split the HE support field into HE and "pseudo HE", the latter is really for AP and doesn't implement trigger frame handling for example. Use the new field for AP mode. Signed-off-by:
-
Ilan Peer authored
The usage of the 'dtim_period' value was wrong, as it is only a multiplier of the beacon interval, and thus, beacon interval should also be considered. Fix it. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
-
Johannes Berg authored
In iwl_mvm_mac_ctxt_get_lowest_rate() we were still accessing vif->bss_conf without any multi-link provisions, and also the info->band, both of which isn't valid in MLO. Fix the code to look at the correct link. In case of EAPOL transmissions for the initial 4-way-HS, look up the correct link here as well, and warn if multiple are active. Signed-off-by:
-
Gregory Greenman authored
When rx/tx queues are being freed, on a different CPU there could be still rx flow running. Call napi_synchronize() to prevent such a race. Signed-off-by:
Benjamin Berg <benjamin.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
For some devices, in client mode, we support full bandwidth uplink multi-user MIMO. Add the necessary capability. Signed-off-by:
-
- 14 Apr, 2023 20 commits
-
-
Rob Herring authored
bcma/main.c uses of_dma_configure() which is declared in of_device.h. of_device.h gets implicitly included by of_platform.h, but that is going to be removed soon. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Bitterblue Smith authored
Handle them the same way as the devices with 3-4 USB out endpoints. This is needed for the RTL8192FU. Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
-
Bitterblue Smith authored
Add some new members to rtl8xxxu_fileops and use them instead of checking priv->rtl_chip. Signed-off-by:
-
Marek Vasut authored
Add SDIO ids for use with the muRata 1YN (Cypress CYW43439). The odd thing about this is that the previous 1YN populated on M.2 card for evaluation purposes had BRCM SDIO vendor ID, while the chip populated on real hardware has a Cypress one. The device ID also differs between the two devices. But they are both 43439 otherwise, so add the IDs for both. On-device 1YN (43439), the new one, chip label reads "1YN": ``` /sys/.../mmc_host/mmc2/mmc2:0001 # cat vendor device 0x04b4 0xbd3d ``` EA M.2 evaluation board 1YN (43439), the old one, chip label reads "1YN ES1.4": ``` /sys/.../mmc_host/mmc0/mmc0:0001/# cat vendor device 0x02d0 0xa9a6 ``` Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
Marek Vasut <marex@denx.de> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Ping-Ke Shih authored
In AP mode, 'sta' could be NULL if sending broadcast/multicast packets, so we should check before accessing, or it causes crash: BUG: kernel NULL pointer dereference, address: 0000000000000004 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 2 PID: 92 Comm: kworker/u33:0 Tainted: G OE Workqueue: rtw89_tx_wq rtw89_core_txq_work [rtw89_core] RIP: 0010:rtw89_core_tx_update_desc_info+0x2cc/0x7d0 [rtw89_core] Code: e2 01 41 be 04 00 00 00 41 8b 84 c4 0c 01 00 00 75 0d 45 31 f6 ... RSP: 0018:ffffb4cf807afce0 EFLAGS: 00010297 RAX: 0000000000000001 RBX: ffffb4cf807afd48 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001 RBP: ffffb4cf807afd30 R08: ffff9b28c1e59808 R09: ffff9b28c0297100 R10: 00000000052cf7c4 R11: 00000000052cf7c4 R12: ffff9b28c1602040 R13: ffff9b28c07b3000 R14: 0000000000000004 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff9b2a73280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000004 CR3: 00000001ca410003 CR4: 00000000000606e0 Call Trace: <TASK> rtw89_core_tx_write+0x7c/0x100 [rtw89_core] rtw89_core_txq_work+0x1b4/0x530 [rtw89_core] process_one_work+0x222/0x3f0 worker_thread+0x50/0x3f0 kthread+0x16b/0x190 ? rescuer_thread+0x3a0/0x3a0 ? set_kthread_struct+0x50/0x50 ret_from_fork+0x22/0x30 </TASK> Fixes: e5307c9c ("wifi: rtw89: set data lowest rate according to AP supported rate") Signed-off-by:
-
Eric Huang authored
Use primary channel index to determine which 5 MHz mask should be enable. This mask is used to prevent noise from channel edge to effect CCA threshold in wide bandwidth (>= 40 MHZ). Fixes: 1b00e923 ("rtw89: 8852c: add set channel of BB part") Fixes: 6b069898 ("wifi: rtw89: 8852b: add chip_ops::set_channel") Cc: stable@vger.kernel.org Signed-off-by:
Eric Huang <echuang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
These tables are used by RF calibrations to assist to configure PHY and RF registers. Signed-off-by:
-
Ping-Ke Shih authored
These tables contain BB and RF parameters that driver will load them into registers. It also contains TX power according to country, band, rate and so on. Increasing thermal can cause TX power degraded, so power tracking tables are defined to compensate TX power. Internal version of these tables: - HALBB_029_106_15 (V17) - HALRF_029_00_089 * Radio A 0x22 * NCTL 0x5 Signed-off-by:
-
Ping-Ke Shih authored
These tables contain BB and RF parameters that driver will load them into registers. It also contains TX power according to country, band, rate and so on. Increasing thermal can cause TX power degraded, so power tracking tables are defined to compensate TX power. Internal version of these tables: - HALBB_029_106_15 (V17) - HALRF_029_00_089 * Radio A 0x22 * NCTL 0x5 Signed-off-by:
-
Ping-Ke Shih authored
Many settings of 8851B are like 8852A or 8852B. Change them to proper settings as hardware design. Signed-off-by:
-
Ping-Ke Shih authored
Many settings of 8851B are the same as 8852B or 8852A, like DLE (Data link engine), security engine and so on. Update them according to hardware design. Signed-off-by:
-
Ping-Ke Shih authored
For two RF paths chips, we normally set path B as main path by default. 8851B has single one RF path, so set TX path to A and set mapping of path B to 0. Signed-off-by:
-
Ping-Ke Shih authored
The chip contains digital and analog parts, and each of them has its own version number. This is used by BT coexistence mechanism to make strategy decision for different analog version. Signed-off-by:
-
Eric Huang authored
Turn on hardware CFO (central frequency offset) compensation based on IC capability, and improve digital CFO compensation accuracy by using more fixed points number. Signed-off-by:
-
Zong-Zhe Yang authored
One chip can have different RFE (RF front end) types which we will judge at runtime. And, different RFE types may use different RF parameter tables. Though we didn't really meet this case previously, we are going to meet it on upcoming chip RTL8851B. So, this commit handles parameter tables for runtime RFE type. We now encapsulate rtw89_txpwr_rule_<2/5/6>ghz tables into rtw89_rfe_parms. Then, each chip defines its default parameter tables, and if needed, it can configure extra parameter tables by RFE type. Finally we determine runtime parameter tables by RFE type if one is configured. Otherwise, we use the default parameter tables. For now, we just move all settings under default parameter tables. We will configure parameter tables by RFE types in separate commits afterwards. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
In the discuss threads [1] [2], new firmware format break user space because older drivers can't recognize new firmware format. To avoid this, the new format will be named rtw89/rtw8852b_fw-1.bin and only new driver try to load it. Old drivers only load original and understandable firmware rtw89/rtw8852b_fw.bin. More, new driver will be still backward compatible with old firmware, so original firmware can be used by new driver. If there is newer firmware format is introduced, rtw89/rtw8852b_fw-2.bin will be given. The same rules will be applied like above. So, we will have firmware like below in linux-firmware in the future. rtw89/rtw8852b_fw-2.bin rtw89/rtw8852b_fw-1.bin rtw89/rtw8852b_fw.bin After this patch, MODULE_FIRMWARE() of 8852A/B/C become rtw89/rtw8852a_fw.bin rtw89/rtw8852b_fw-1.bin rtw89/rtw8852c_fw.bin [1] https://lore.kernel.org/linux-wireless/df1ce994-3368-a57e-7078-8bdcccf4a1fd@gmail.com/T/#m24cb43be31a762d0ea70bf07f27ae96c59f6931b [2] https://bugzilla.kernel.org/show_bug.cgi?id=217207Signed-off-by:
-
Ping-Ke Shih authored
Since we are going to load more than one firmware and some are not presented or optional, using asynchronous API request_firmware_nowait() will become complicated. Also, we want to use firmware_request_nowarn() to avoid warning messages when loading optional files. So, use schedule_work to be simpler. To abstract loading a firmware or file, define a struct rtw89_fw_req_info containing a struct firmware and a completion to ensure this firmware is loaded completely. Signed-off-by:
-
Zong-Zhe Yang authored
In early feature bitmap obtained from rtw89_early_fw_feature_recognize(), the bits needed to check get increased. It's more friendly to work with RTW89_CHK_FW_FEATURE(). So, we concentrate the flow of iterating FW feature configures and calling RTW89_SET_FW_FEATURE() for various uses. And then, we adjust rtw89_early_fw_feature_recognize() for RTW89_CHK_FW_FEATURE(). Signed-off-by:
-
Po-Hao Huang authored
We used to store operating channel info after associated. However, scan might happen before that. Without switching back to operating channel, authentication or association might fail. Therefore, we switch back to operating channel when the scanning vif's BSSID is non-zero, which implies connected or during attempt to connect. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
Use POWER_ON flag to make sure power on/off is symmetric. Since both remain_on_channel and hw_scan both alter the power state, this makes sure that we don't enter/leave IPS mode twice. Also, replace IPS related functions with inline function that does similar logic so we can track it more easily. Signed-off-by:
-
