Merge tag 'qcom-arm64-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm ARM64 Updates for v4.17" from Andy Gross:

* Fix GIC_CPU_MASK_SIMPLE and SPI5 config on MSM8996
* Add SDM845 and kryo385 documentation
* Add MSM8916 cooling maps, cpu frequency scaling, APCS, and A53 PLL
* Switch APCS to use mailbox on MSM8916
* Add rmtfs-mem on MSM8996

* tag 'qcom-arm64-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: qcom: Fix SPI5 config on MSM8996
  dt-bindings: qcom: Add SDM845 bindings
  dt-bindings: arm: Document kryo385 cpu
  arm64: dts: msm8916: Add cpu cooling maps
  arm64: dts: msm8996: Add rmtfs sharedmem node
  arm64: dts: qcom: msm8916: Add CPU frequency scaling support
  arm64: dts: qcom: msm8916: Add clock properties to the APCS node
  arm64: dts: qcom: msm8916: Probe the APCS mailbox driver
  arm64: dts: qcom: msm8916: Add msm8916 A53 PLL DT node
  arm64: dts: msm8996: Fix wrong use of GIC_CPU_MASK_SIMPLE()

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.

Remove the unused properties from the gpio-fan node.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.

Remove the unused properties from the gpio-fan node.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.

Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'armsoc-versatile-drm-dts' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt

Pull "DTS changes for RealView+Versatile" from Linus Walleij:

This augments the RealView and Versatile device trees to properly
define the VGA and panel connectors in preparation for DRM.

* tag 'armsoc-versatile-drm-dts' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: dts: Augment panel setting for Versatile
  ARM: dts: Add Versatile IB2 device tree
  ARM: dts: Augment VGA connector bridge on Realview PBX
  ARM: dts: Augment VGA connector bridge on Realview EB
  ARM: dts: Augment VGA connector bridge on PB1176
  ARM: dts: Augment VGA connector bridge on PB11MPcore

Merge tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 64-bit DT updates for v4.17" from Kevin Hilman:

- AXG: add/enable UART_A, I2C, RMII, system controller, HW RNG
- accept MAC from u-boot environment
- misc. fixes

* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: make efuse read-only
  ARM64: dts: meson: bump mali450 clk to 744MHz
  meson-gx-socinfo: Add package id for S905H
  ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2
  ARM64: dts: meson: reduce odroid-c2 eMMC maximum rate
  ARM64: dts: amlogic: Convert to new-style SPDX license identifiers
  ARM64: dts: meson-axg: fix pwm_AO_cd compatible
  ARM64: dts: meson-axg: add sec_AO system controller
  ARM64: dts: meson: accept MAC addr from u-boot environment
  ARM64: dts: meson s905x: accept MAC addr from u-boot environment
  ARM64: dts: meson-axg: enable the UART_A controller
  ARM64: dts: meson-axg: complete the pinctrl info for UART_AO_A
  ARM64: dts: meson-axg: uart: Add the pinctrl info description
  ARM64: dts: meson-axg: uart: drop legacy compatible name from EE UART
  ARM64: dts: meson-axg: add RMII pins for ethernet controller
  ARM64: dts: meson-axg: enable I2C Master-1 for the audio speaker
  ARM64: dts: meson-axg: describe pin DT info for I2C controller
  ARM64: dts: meson-axg: add I2C DT info for Meson-AXG SoC
  ARM64: meson-axg: enable hardware rng

Pull "mvebu dt64 for 4.17 (part 2)" from Gregory CLEMENT:

- Add registers clock for all the peripheral nodes that had been yet
  converted for CP110 (Armada 7K/8K)

- Document URL for schematic for the EspressoBin (Armada 3720)

* tag 'mvebu-dt64-4.17-2' of git://git.infradead.org/linux-mvebu:
  arm64: dts: armada-3720-espressobin: Document URL for schematic
  ARM64: dts: marvell: armada-cp110: Add registers clock for the PCIe nodes
  ARM64: dts: marvell: armada-cp110: Add registers clock for the NAND node
  ARM64: dts: marvell: armada-cp110: Add registers clock for the crypto node
  ARM64: dts: marvell: armada-cp110: Add registers clock for the trng node
  ARM64: dts: marvell: armada-cp110: Add registers clock for XOR engine nodes
  ARM64: dts: marvell: armada-cp110: Add registers clock for USB host nodes

Merge tag 'v4.16-next-dts64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt

Pull "ARM: mediatek: dts64 updates for v4.16-next" from Matthias Brugger:

- mt2712e add auxadc devcie

mt7622:
- fix clock bindings description
- add nodes for mmc, usb, SATA, PCI, ethernet, cpufreq, PMIC mt6380,
pinctrl, scpsys and clock devices

* tag 'v4.16-next-dts64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm64: dts: mt2712: Add auxadc device node.
  dt-bindings: clock: mediatek: add missing required #reset-cells
  arm64: dts: mt7622: add mmc related device nodes
  arm64: dts: mt7622: add usb device nodes
  arm64: dts: mt7622: add SATA device nodes
  arm64: dts: mt7622: add PCIe device nodes
  arm64: dts: mt7622: add ethernet device nodes
  arm64: dts: mt7622: add flash related device nodes
  arm64: dts: mt7622: add SoC and peripheral related device nodes
  arm64: dts: mt7622: turn uart0 clock to real ones
  arm64: dts: mt7622: add cpufreq related device nodes
  arm64: dts: mt7622: add PMIC MT6380 related nodes
  arm64: dts: mt7622: add pinctrl related device nodes
  arm64: dts: mt7622: add power domain controller device nodes
  arm64: dts: mt7622: add clock controller device nodes

Merge tag 'v4.16-next-dts32' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt

Pull "ARM: mediatek: dts32 updates for v4.16-next" from Matthias Brugger:

mt7623:
- fix style issues of the dts
- add cpu clock properties
- add PCI controller
- add mt7623 reference board

banapi-r2:
- enable missing uarts
- fix regulator for mmc
- fix USB initialization

* tag 'v4.16-next-dts32' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm: dts: mt7623: add PCIe related nodes
  arm: dts: mt7623: use - instead of _ in DT node name
  arm: dts: mt7623: remove useless property pinctrl-names at node switch@0
  arm: dts: mt7623: add related clock properties to cpu[1-3] nodes
  arm: dts: mt7623: enable three available UARTs on bananapi-r2
  arm: dts: mt7623: fix the regulators mmc should use on bananapi-r2
  arm: dts: mt7623: fix USB initialization fails on bananapi-r2
  dt-bindings: arm: mediatek: add support for more mt7623 reference boards

Merge tag 'samsung-dt-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Pull "Samsung DTS ARM changes for v4.17, part two" from Krzysztof Kozłowski:

1. Fix audio on Exynos5250 Chromebook Snow.
2. Enable HDMI audio Chromebook Snow, Peach Pit and Peach Pi.
3. Fix debounce of "OK" key on Midas (Trats2, Galaxy S3) boards.

* tag 'samsung-dt-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Add #sound-dai-cells property to exynos5250 i2s nodes
  ARM: dts: exynos: Fix "debounce-interval" property misspelling in Midas
  ARM: dts: exynos: Enable HDMI audio support on Peach Pi
  ARM: dts: exynos: Enable HDMI audio support on Peach Pit
  ARM: dts: exynos: Enable HDMI audio on Snow Chromebook
  ARM: dts: exynos: Add missing clock and DAI properties to the max98095 node in Snow Chromebook
  ARM: dts: exynos: Add audio clocks configuration for Snow Chromebook
  ARM: dts: exynos: Add #sound-dai-cells property to hdmi node in exynos5250.dtsi

Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:

* Silk board with R-Car E2 (r8a7794) SoC
  - Add r1ex24002 EEPROM to DT

    Magnus Damm says "Extend the Silk board support to include U14 which is
    an I2C based EEPROM hooked up to the I2C1 bus."

  - Add GPIO keys to DT

    Magnus Damm says "Extend the Silk board support to include SW3, SW4,
    SW6 and SW12. They are all connected via GPIO lines and handled by the
    gpio-keys driver"

* Marzen board with R-Car H1 (r7a7779) SoC
  - Add SDHI0 VCCQ Regulator

    Magnus Damm says "Add support for the on-board voltage regulator hooked
    up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
    regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
    tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
    OUT goes to the pull-ups for the data pins of SDHI0."

* Porter board with R-Car M3W (r8a7791) SoC
  - Fix HDMI output routing

    Laurent Pinchart says "The HDMI encoder is connected to the RGB output
    of the DU, which is port@0, not port@1."

* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
  iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
  - Enable cmt0

* Stout board with R-Car H2 (r8a7790) SoC
  - Initial support

* Lager board with R-Car H2 (r8a7790) SoC
  - Add CEC clock for HDMI transmitter

    Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
    fixed clock for the CEC block. Specify this in the dts to enable CEC
    support."

  - Move cec_clock to root node

    By definition nodes without a bus address do not belong on the bus

* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
  - Fix "debounce-interval" property misspelling

* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
  - Add IPMMU DT nodes
  - Add VSP support

* R-Car Gen2 boards
  - Use I2C demuxer for

    This allows run-time switching between alternate I2C IP blocks

* R-Car Gen2 and RZ/G1 SoCs
  - Clean up DT files to ease future maintenance
    + add soc node for IP attached to the bus
    + sort subnodes of soc and root node
    + consistently use single space after =

* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
  - Reduce size of thermal registers

    According to the "User's Manual: Hardware" v2.00 the registers at base
    0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
    case on the r8a73a4 (R-Mobile APE6).

    This should not have any runtime affect as mapping granularity is
    PAGE_SIZE.

* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
  ARM: dts: silk: Add GPIO keys to DT
  ARM: dts: silk: Add r1ex24002 EEPROM to DT
  ARM: dts: marzen: Add SDHI0 VCCQ Regulator
  ARM: dts: stout: Initial r8a7790 Stout board support
  ARM: dts: lager: Move cec_clock to root node
  ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
  ARM: dts: gose: use demuxer for I2C4
  ARM: dts: gose: use demuxer for I2C2
  ARM: dts: silk: use demuxer for I2C1
  ARM: dts: alt: use demuxer for I2C1
  ARM: dts: porter: use demuxer for I2C2
  ARM: dts: koelsch: use demuxer for I2C4
  ARM: dts: koelsch: use demuxer for I2C2
  ARM: dts: lager: use demuxer for IIC3/I2C3
  ARM: dts: lager: use demuxer for IIC2/I2C2
  ARM: dts: r8a7745: Add VSP support
  ARM: dts: r8a7743: Add VSP support
  ARM: dts: r8a7745: Add IPMMU DT nodes
  ARM: dts: r8a7743: Add IPMMU DT nodes
  ARM: dts: r8a7745: sort subnodes of soc node
  ...

Merge tag 'renesas-dt-bindings-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Bindings Updates for v4.17" from Simon Horman:

* Document the bindings for:
  - R-Car V3H (r8a77980) SoC
  - Condor board with V3H (r8a77980) SoC
  - Stout (ADAS Starterkit) board with R-Car H2 (r8a7790) SoC
  - R-Car M3-N (r8a77965) SoC
  - Salvator-X and Salvator-XS boards with R-Car M3-N (r8a77965) SoC
* Document that Armadillo-800 is compatibie with R-Mobile A1 (r8a7740) SoC
* Document part numbers of Wheat and V3MSK boards

* tag 'renesas-dt-bindings-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  dt-bindings: arm: Document Renesas R-Car M3-N-based Salvator-X board
  dt-bindings: arm: Document Renesas R-Car M3-N-based Salvator-XS board
  dt-bindings: arm: Document Renesas V3MSK and Wheat board part numbers
  dt-bindings: arm: Document SoC compatible value for Armadillo-800 EVA
  dt-bindings: arm: Document R-Car M3-N SoC DT bindings
  dt-bindings: arm: Document Renesas H2-based Stout DT bindings
  dt-bindings: arm: document Condor board bindings
  dt-bindings: arm: document R8A77980 SoC bindings

Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:

* R-Car Gen3 boards and SoCs
  - Make phy-mode of EtherAVB a board-specific property.

    The SoC DTs file now uses "rgmii" and boards override this with
    "rgmii-txid" as appropriate. Previously "rgmii-txid" was used
    in SoC DTs but this did not describe that more sophiticated
    functionality is a board rather than SoC property.

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* R-Car D3 (r8a77995)
  - Add I2C nodes and then describing the PCA9654 I/O expander connected to
    the I2C0 bus.

* Eagle board with R-Car V3M (r8a77970) SoC
  - Enable PFC support for configuring SCIF0 pins
    This uses PFC support added to the V3M DT

  - Describe EtherAVB PHY IRQ
    This uses support for GPIO added to the V3M DT

  - Enable I2C0 support

    Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
    PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
    we're only describing the former chip now)."

* R-Car V3M (r8a77970) SoCs
  - Add PFC support
  - Describe GPIO devices
  - Describe I2C devices
  - Srt subnodes of root node alphabetically to eas future maintence overhead

* Draak board with R-Car D3 (r8a77995) SoC
  - Enable SDHI2

    Wolfram Sang says "The single SDHI controller is connected to eMMC."

  - Enable DU

    Kieran Bingham says "Enable the DU, providing only the VGA output for
    now."

* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
  - Move nodes which have no reg property out of bus
    By deffinition the bus only has hardware with an address on the bus

  - Remove non-existing STBE region from EtherAVB
    Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs

* R-Car D3 (r8a77995) SoC
  - Add FCPV, VSP and DU support

    Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
    One VSPBS can be used as a dual-input image blender, while two VSPD
    instances can be utilised as part of a display (DU) pipeline.

    Add support for these, along with their required FCPV nodes."

* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
  - Add GPIO extender
    This is a basis for follow-up work to configure the GPIOs of the extender

* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
  - Initial upstream support

* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
  - Add OPPs table for cpu devices
    This, along with recently upstreamed Z and Z2 clock support allows
    use of CPUFreq with both A57 and A53 CPUs.

  - Add thermal cooling management
    Allows the use of CPUFreq as a cooling device on A57 CPUs

  - Correct register size of thermal node

    Niklas Söderlund says "To be able to read fused calibration values from
    hardware the size of the register resource of TSC1 needs to be
    incremented to cover one more register which holds the information if
    the calibration values have been fused or not.

    Instead of increasing TSC1 size to the value from the datasheet update
    all TSC's size to the smallest granularity of the address decoder
    circuitry"

  - Fix register mappings on VSPs

    Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
    register space is mapped correctly to support this."

* R-Car H3 (r8a7795) SoC
  - Move SCIF node into alphabetical order to ease future maintenance overhead

  - Add IPMMU-PV1 device node

    This resolves an oversight when IPMMU nodes were added to the H3 DT.
    All IPMMU devices should now be described in DT.

  - Add missing SYS-DMAC2 dmas

    Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
    can make use of DMA are wired to either SYS-DMAC0 only, or to both
    SYS-DMAC1 and SYS-DMAC2.

    Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
    SCIF[0125], and I2C[0-2].  These were initially left out because early
    firmware versions prohibited using SYS-DMAC2.  This restriction has
    been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
    2016)."

* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
  arm64: dts: renesas: v3msk: add SCIF0 pins
  arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
  arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
  arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
  arm64: dts: renesas: eagle: add I2C0 support
  arm64: dts: renesas: r8a77970: add I2C support
  arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
  arm64: dts: renesas: r8a77965: Add EtherAVB device node
  arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
  arm64: dts: renesas: eagle: Override EtherAVB phy-mode
  arm64: dts: renesas: draak: Override EtherAVB phy-mode
  arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
  arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
  arm64: dts: renesas: r8a77965: Add INTC-EX device node
  arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
  arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
  ...

Merge tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "arm64: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:

Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.

* tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: tegra: Enable AHCI on Jetson TX1
  arm64: tegra: Add SATA node for Tegra210
  arm64: tegra: Add device tree for the Tegra194 P2972-0000 board
  arm64: tegra: Add Tegra194 chip device tree

Merge tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "ARM: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:

Support for the VDE is added on Tegra30 along with some general cleanup
and some improvements to the various Toradex boards.

* tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: apalis-tk1: Support v1.2 hardware revision
  ARM: tegra: apalis-tk1: Copyright period, spurious newlines
  ARM: tegra: apalis-tk1: Hog group for ethernet, PCIe, reset GPIOs
  ARM: tegra: apalis-tk1: Add missing as3722 gpio0 configuration
  ARM: tegra: apalis-tk1: Activate PWM pin muxing for pwm3
  ARM: tegra: apalis-tk1: Set critical trips
  ARM: tegra: apalis/colibri: Remove unneeded reg property
  ARM: tegra: apalis/colibri: Use correct compatible for RTC
  ARM: tegra: Fix I2C bus frequencies on Apalis/Colibri
  ARM: tegra: venice2: Remove duplicate pcie-1 node
  ARM: tegra: beaver: Remove invalid uses of rsvd1
  ARM: tegra: Use proper IRQ type definitions
  ARM: tegra: Fix ULPI regression on Tegra20
  ARM: tegra: Add unit address to VDE IRAM area
  ARM: tegra: Add video decoder node on Tegra30
  ARM: tegra: Add IRAM node on Tegra30

Merge tag 'tegra-for-4.17-dt-bindings' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "dt-bindings: Tegra changes for v4.17-rc1" from Thierry Reding:

Mostly cleanup of existing bindings and initial support for Tegra194.

* tag 'tegra-for-4.17-dt-bindings' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt/bindings: Fix binding examples for Tegra GMI controller
  dt-bindings: phy: Clarify ULPI PHY source clock
  dt-bindings: tegra: Add documentation for nvidia,tegra194-pmc
  dt-bindings: tegra: Add missing chips and NVIDIA boards

This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA.

The "clcd" clock was incorrectly named, the proper name
(from bindings) is "clcdclk". So far drivers survived
by just getting the first clock, but future drivers will
use named clocks.

We add the panel connector to the
"arm,versatile-tft-panel" as well, the signals actually
fork on the board, reaching both the VGA DAC and the
display connector.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Versatile board can be equipped with a interface board
just named "IB2". This was created in the early 2000s for
prototyping GSM candybar phone form factor products.

The IB2 board contains:
- Cascaded interrupt controller
- Enfora Enabler GSM0308 quad-band module with antenna and
  separate audio jack
- Keypad with joystick
- Sanyo 2.5" color display
- A 28-pin connector for mounting a camera

This adds a DTS file for the combination of the Versatile AB
with an IB2 daughterboard mounted, making the LED blink and
making the system controller available for drivers, such as
the panel driver.

The device tree bindings already exist in
Documentation/devicetree/bindings/arm/arm-boards.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.

Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The schematic of the espressobin is publicly available, add a comment
where to find it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Add auxadc device node for MT2712.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

This patch adds some device nodes for the PCIe function block and updates
related pinmux.

Moreover, we add interrupt-map properties in both parent and children as
the chip only has one IRQ per slot that is connected to all INTx and get
propagated through the bridges and it also represents the root ports own
interrupts.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Complement the missing clock properties cpu[1-3] should depend on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

All ethsys, pciesys and ssusbsys internally include reset controller, so
explicitly add back these missing cell definitions to related bindings
and examples.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>