Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Let MODULE_LICENCE match the SPDX header which is correctly based on the
previous textual description.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add code to handle IS_S_RX_FIFO_FULL_SHIFT interrupt to support
master write request with >= 64 bytes.

Iproc has a slave rx fifo size of 64 bytes.
Rx fifo full interrupt (IS_S_RX_FIFO_FULL_SHIFT) will be generated
when RX fifo becomes full. This can happen if master issues write
request of more than 64 bytes.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Handle single or multi byte master read request with or without
repeated start.

Fixes: c245d94e ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Fix typo in bcm_iproc_i2c_slave_isr().
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Update slave isr mask (ISR_MASK_SLAVE) to include remaining
two slave interrupts.

Fixes: c245d94e ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Handle only slave interrupts which are enabled.

The IS_OFFSET register contains the interrupt status bits which will be
set regardless of the enabling of the corresponding interrupt condition.
One must therefore look at both IS_OFFSET and IE_OFFSET to determine
whether an interrupt condition is set and enabled.

Fixes: c245d94e ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Handle Master aborted error by flushing tx and rx fifo
and reinitializing the hw.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

'flags' and 'io' are needed first, so they should be at the beginning of
the private struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.

Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

platform_device_unregister() is NULL-aware and thus doesn't required a
duplication check in i801_del_mux(). Besides that it's also error pointer
aware, and we may drop unneeded assignment in i801_add_mux() followed by
conversion to PTR_ERR_OR_ZERO() for the returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Since gpiod_remove_lookup_table() is NULL-aware, no need to have this check
in the caller. Drop duplicate NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The usual pattern for the remove calls, like gpiod_remove_lookup_table(),
is to be NULL-aware, i.o.w. become a no-op whenever parameter is NULL.
Update gpiod_remove_lookup_table() call to follow this pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 2000 usec to 400
usec. It greatly improves performance of I2C transactions.

Reliability of setting polling time to 400 usec has been thoroughly
validated across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Update license to SPDX-License.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c_new_client_device() already prints an error when it fails. Some
ACPI tables contain 2 ACPI devices describing the same i2c-client,
leading to errors like this:

[    1.620847] i2c i2c-4: Failed to register i2c client MAGN0001:00 at 0x1d (-16)
[    1.620870] i2c i2c-4: failed to add I2C device MAGN0001:00 from ACPI

There is nothing we can do about the first -EBUSY error being logged,
but the second error does not really add any new information, so lets
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull s390 cleanups from Vasily Gorbik:
 "Update defconfigs and sort config select list"

* tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/Kconfig: sort config S390 select list once again
  s390: update defconfigs

Pull power management fixes from Rafael Wysocki:
 "These fix a crash in intel_pstate during resume from suspend-to-RAM
  that may occur after recent changes and two resource leaks in error
  paths in the operating performance points (OPP) framework, add a new
  C-states table to intel_idle and update the cpuidle MAINTAINERS entry
  to cover the governors too.

  Specifics:

   - Fix recently introduced crash in the intel_pstate driver that
     occurs if scale-invariance is disabled during resume from
     suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
     values made by the platform firmware (Rafael Wysocki).

   - Fix a memory leak and add a missing clk_put() in error paths in the
     OPP framework (Quanyang Wang, Viresh Kumar).

   - Add new C-states table for SnowRidge processors to the intel_idle
     driver (Artem Bityutskiy).

   - Update the MAINTAINERS entry for cpuidle to make it clear that the
     governors are covered by it too (Lukas Bulwahn)"

* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_idle: add SnowRidge C-state table
  cpufreq: intel_pstate: Fix fast-switch fallback path
  opp: Call the missing clk_put() on error
  opp: fix memory leak in _allocate_opp_table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

* pm-cpufreq:
  cpufreq: intel_pstate: Fix fast-switch fallback path

* pm-cpuidle:
  intel_idle: add SnowRidge C-state table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

Pull SCSI fixes from James Bottomley:
 "This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).

  The big core two fixes are for power management ("block: Do not accept
  any requests while suspended" and "block: Fix a race in the runtime
  power management code") which finally sorts out the resume problems
  we've occasionally been having.

  To make the resume fix, there are seven necessary precursors which
  effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
  in block is automatically a power management exempt one.

  All of the non-PM preempt cases are removed except for the one in the
  SCSI Parallel Interface (spi) domain validation which is a genuine
  case where we have to run requests at high priority to validate the
  bus so this becomes an autopm get/put protected request"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
  scsi: cxgb4i: Fix TLS dependency
  scsi: ufs: Un-inline ufshcd_vops_device_reset function
  scsi: ufs: Re-enable WriteBooster after device reset
  scsi: ufs-mediatek: Use correct path to fix compile error
  scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
  scsi: block: Do not accept any requests while suspended
  scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
  scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
  scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
  scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
  scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
  scsi: block: Introduce BLK_MQ_REQ_PM
  scsi: block: Fix a race in the runtime power management code
  scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
  scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
  scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
  scsi: ufs-pci: Fix restore from S4 for Intel controllers
  scsi: ufs-mediatek: Keep VCC always-on for specific devices
  scsi: ufs: Allow regulators being always-on
  scsi: ufs: Clear UAC for RPMB after ufshcd resets
  ...

Pull block fixes from Jens Axboe:
 "Two minor block fixes from this last week that should go into 5.11:

   - Add missing NOWAIT debugfs definition (Andres)

   - Fix kerneldoc warning introduced this merge window (Randy)"

* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
  block: add debugfs stanza for QUEUE_FLAG_NOWAIT
  fs: block_dev.c: fix kernel-doc warnings from struct block_device changes

Pull io_uring fixes from Jens Axboe:
 "A few fixes that should go into 5.11, all marked for stable as well:

   - Fix issue around identity COW'ing and users that share a ring
     across processes

   - Fix a hang associated with unregistering fixed files (Pavel)

   - Move the 'process is exiting' cancelation a bit earlier, so
     task_works aren't affected by it (Pavel)"

* tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
  kernel/io_uring: cancel io_uring before task works
  io_uring: fix io_sqe_files_unregister() hangs
  io_uring: add a helper for setting a ref node
  io_uring: don't assume mm is constant across submits

Commit 436e980e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).

Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For cancelling io_uring requests it needs either to be able to run
currently enqueued task_works or having it shut down by that moment.
Otherwise io_uring_cancel_files() may be waiting for requests that won't
ever complete.

Go with the first way and do cancellations before setting PF_EXITING and
so before putting the task_work infrastructure into a transition state
where task_work_run() would better not be called.

Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.

Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Setting a new reference node to a file data is not trivial, don't repeat
it, add and use a helper.

Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull ceph fixes from Ilya Dryomov:
 "A fix for an edge case in MClientRequest encoding and a couple of
  trivial fixups for the new msgr2 support"

* tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client:
  libceph: add __maybe_unused to DEFINE_MSGR2_FEATURE
  libceph: align session_key and con_secret to 16 bytes
  libceph: fix auth_signature buffer allocation in secure mode
  ceph: reencode gid_list when reconnecting

Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville
platforms.

The following has been changed.

 1. C1E latency changed from 10us to 15us. It was measured using the
    open source "wult" tool (the "nic" method, 15us is the 99.99th
    percentile).

 2. C1E power break even changed from 20us to 25us, which may result
    in less C1E residency in some workloads.

 3. C6 latency changed from 50us to 130us. Measured the same way as C1E.

The C6 C-state is supported only by some SnowRidge revisions, so add a C-state
table commentary about this.

On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of
the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even
though C6 is present in the table, the driver will only use it if the CPU does
support it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When sugov_update_single_perf() falls back to the "frequency"
path due to the missing scale-invariance, it will call
cpufreq_driver_fast_switch() via sugov_fast_switch()
and the driver's ->fast_switch() callback will be invoked,
so it must not be NULL.

However, after commit a365ab6b ("cpufreq: intel_pstate: Implement
the ->adjust_perf() callback") intel_pstate sets ->fast_switch() to
NULL when it is going to use intel_cpufreq_adjust_perf(), which is a
mistake, because on x86 the scale-invariance may be turned off
dynamically, so modify it to retain the original ->adjust_perf()
callback pointer.

Fixes: a365ab6b ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull operating performance points (OPP) framework fixes for 5.11-rc2
from Viresh Kumar:

"This contains two patches to fix freeing of resources in error paths."

* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
  opp: Call the missing clk_put() on error
  opp: fix memory leak in _allocate_opp_table

...and add comments at the top and bottom.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

This was missed in 021a2446. Leads to the numeric value of
QUEUE_FLAG_NOWAIT (i.e. 29) showing up in
/sys/kernel/debug/block/*/state.

Fixes: 021a2446
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Fix new kernel-doc warnings in fs/block_dev.c:

../fs/block_dev.c:1066: warning: Excess function parameter 'whole' description in 'bd_abort_claiming'
../fs/block_dev.c:1837: warning: Function parameter or member 'dev' not described in 'lookup_bdev'

Fixes: 4e7b5671 ("block: remove i_bdev")
Fixes: 37c3fc9a ("block: simplify the block device claiming interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-fsdevel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge misc fixes from Andrew Morton:
 "16 patches

  Subsystems affected by this patch series: mm (selftests, hugetlb,
  pagecache, mremap, kasan, and slub), kbuild, checkpatch, misc, and
  lib"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: slub: call account_slab_page() after slab page initialization
  zlib: move EXPORT_SYMBOL() and MODULE_LICENSE() out of dfltcc_syms.c
  lib/zlib: fix inflating zlib streams on s390
  lib/genalloc: fix the overflow when size is too big
  kdev_t: always inline major/minor helper functions
  sizes.h: add SZ_8G/SZ_16G/SZ_32G macros
  local64.h: make <asm/local64.h> mandatory
  kasan: fix null pointer dereference in kasan_record_aux_stack
  mm: generalise COW SMC TLB flushing race comment
  mm/mremap.c: fix extent calculation
  mm: memmap defer init doesn't work as expected
  mm: add prototype for __add_to_page_cache_locked()
  checkpatch: prefer strscpy to strlcpy
  Revert "kbuild: avoid static_assert for genksyms"
  mm/hugetlb: fix deadlock in hugetlb_cow error path
  selftests/vm: fix building protection keys test

It's convenient to have page->objects initialized before calling into
account_slab_page().  In particular, this information can be used to
pre-alloc the obj_cgroup vector.

Let's call account_slab_page() a bit later, after the initialization of
page->objects.

This commit doesn't bring any functional change, but is required for
further optimizations.

[akpm@linux-foundation.org: undo changes needed by forthcoming mm-memcg-slab-pre-allocate-obj_cgroups-for-slab-caches-with-slab_account.patch]

Link: https://lkml.kernel.org/r/20201110195753.530157-1-guro@fb.comSigned-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>