- 20 Oct, 2021 40 commits
-
-
Daniel Golle authored
Some platforms boot from SD card and don't come with calibration data stored anywhere on the board. As EEPROM data is rather small it can be embedded into the device tree to be loaded from there by the mt76. Signed-off-by:
Daniel Golle <daniel@makrotopia.org> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Reduce MT_TX_STATUS_SKB_TIMEOUT to 250ms Tested-by: mrkiko.rs@gmail.com Co-developed-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Substitute sk_buff_head status_list with spinlock_t status_lock since we just need it for locking Tested-by: mrkiko.rs@gmail.com Signed-off-by:
-
Lorenzo Bianconi authored
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is always set to NULL Tested-by: mrkiko.rs@gmail.com Signed-off-by:
-
Lorenzo Bianconi authored
Introduce per-wcid idr to manage packet id for txs. This allow fast idr lookup and skb queueing at the same time. Tested-by: mrkiko.rs@gmail.com Signed-off-by:
-
Lorenzo Bianconi authored
Unlock 6GHz band if supported by the device. Configure HE 6G capabilities. Tested-by:
Deren Wu <deren.wu@mediatek.com> Signed-off-by:
-
Lorenzo Bianconi authored
Introduce 6GHz channel list in mt76 module. This is a preliminary patch to unlock 6GHz band for mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to enable 6GHz band for mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to enable 6GHz band for mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
Introduce sta_rec_he_6g_capa tlv in order configure the mcu with 6GHz capabilities. This is a preliminary patch to enable 6GHz band for mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
Configure tx rate power for 6GHz channels. This is a preliminary patch to enable 6GHz band for mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
Configure 6GHz channels defining mcu channel domain. This is a preliminary patch to enable 6GHz band on mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to support 6GHz band on mt7921 devices. Tested-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to support 6GHz band on mt7921 devices. Tested-by:
-
Ben Greear authored
This adds the new mib counters from last patch into ethtool stats. Signed-off-by:
-
Ben Greear authored
Add register definitions and read & accumulate them in the mib polling logic. Note that some registers should not be read since firmware is already reading them. If driver reads those, they will be cleared-on-read, and so the firmware stats will be incorrect. For these 'do-not-read' stats, add them to the registers definition so that other developers can be aware of these constraints, but do not actually read them in the driver. Signed-off-by:
-
Ben Greear authored
These counters are clear-on-read, so we need to accumulate them in the update_stats poll logic, and read the accumulated values instead of directly doing register reads when reporting to debugfs and ethtool stats. Signed-off-by:
-
Ben Greear authored
The tx status callback is not called for every frame, so those specific counters under-count, but at least they give some idea of what is going on. Signed-off-by:
-
Ben Greear authored
Add tx-mode (ofdma, ht, vht, HE) histogram, tx-ru-idx histogram, and tx-bandwidth histogram. Also add tx attempts and tx success counters. All of this is per-station. Signed-off-by:
-
Ben Greear authored
This exposes some tx-path stats to the ethtool API, so that ethtool -S wlanX provides some more useful info. Signed-off-by:
-
Sean Wang authored
We should pass the error code to the caller immediately to avoid the possible infinite retry to release the semaphore. Fixes: 1c099ab4 ("mt76: mt7921: add MCU support") Co-developed-by:
YN Chen <YN.Chen@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Sean Wang authored
Robustify hardware initialization in the current driver probing flow to get rid of the device is possibly lost after the machine boot due to possible firmware abnormal state by trying to recover the failure with more chances. Tested-by:
Leon Yen <Leon.Yen@mediatek.com> Tested-by:
-
Lorenzo Bianconi authored
Fix possible infinite loop in mt7915_load_patch if mt7915_mcu_patch_sem_ctrl always returns an error. Fixes: e57b7901 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by:
-
Lorenzo Bianconi authored
Check all possible errors returned in mt7915_mcu_init routine. Signed-off-by:
-
Xingbang Liu authored
as you are already in a tasklet, it is unnecessary to call spin_lock_bh. Signed-off-by:
Xingbang Liu <liu.airalert@gmail.com> Signed-off-by:
-
Lorenzo Bianconi authored
mt7921_sta_stats is no longer needed Signed-off-by:
-
Lorenzo Bianconi authored
Remove unused tx rate reporting through mcu tx done event since now tx status is fully supported Signed-off-by:
-
Lorenzo Bianconi authored
Report tx rate from tx status packets instead of receiving periodic mcu event. This improves flexibility, accuracy and AQL performance, and simplifies code flow for better readability. Signed-off-by:
-
Lorenzo Bianconi authored
Introduce infrastructure support for tx status reporting Signed-off-by:
-
Lorenzo Bianconi authored
Similar to mt7915, introduce mt7921_txwi_free to report tx rate to mac80211. This is a preliminary patch to add proper tx status report. Signed-off-by:
-
Ryder Lee authored
Without this change, garbage is seen in the hwmon name and sensors output for mt7615 is garbled. Fixes: 109e505a ("mt76: mt7615: add thermal sensor device support") Signed-off-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
-
Ben Greear authored
Without this change, garbage is seen in the hwmon name and sensors output for mt7915 is garbled. It appears that the hwmon logic does not make a copy of the incoming string, but instead just copies a char* and expects it to never go away. Fixes: 33fe9c63 ("mt76: mt7915: add thermal sensor device support") Signed-off-by:
-
Ryder Lee authored
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd. Signed-off-by:
-
Felix Fietkau authored
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq handling, so it must not be called in a pure process context with BH enabled. Signed-off-by: -
Ryder Lee authored
Give a proper boottime_ns value for netlink RX to avoid scan issues with Android. Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below. It has been compile tested. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
jing yangyang authored
./drivers/net/wireless/mediatek/mt76/mt7615/usb_sdio.c:172:8-9:WARNING: return of 0/1 in function 'mt7663_usb_sdio_tx_status_data' with return type bool Return statements in functions returning bool should use true/false instead of 1/0. Generated by: scripts/coccinelle/misc/boolreturn.cocci Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
jing yangyang <jing.yangyang@zte.com.cn> Signed-off-by:
-
Lorenzo Bianconi authored
mt7921 mac work can be idle for a long time due to runtime-pm so update mib counters dumping phy stats Signed-off-by:
-
Lorenzo Bianconi authored
Add missing device wakeup in debugfs code if we are accessing chip registers. Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support") Signed-off-by:
-
Ryder Lee authored
Rename "queues" to "tx-queues" to reflect its meaning. Signed-off-by:
-
