- 23 May, 2019 13 commits
-
-
David S. Miller authored
Andrew Lunn says: ==================== net: phy: T1 support T1 PHYs make use of a single twisted pair, rather than the traditional 2 pair for 100BaseT or 4 pair for 1000BaseT. This patchset adds link modes for 100BaseT1 and 1000BaseT1, and them makes use of 100BaseT1 in the list of PHY features used by current T1 drivers. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
Now that there is a link mode for 100BaseT1, use it in phy_basic_t1_features so T1 PHY drivers will indicate this mode via the Ethtool API. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
Add link modes for 100Mbps and 1Gbps over a single pair. Signed-off-by:
-
Trent Piepho authored
This was being done in config the first time the phy was configured. Should be in the probe method. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Trent Piepho <tpiepho@impinj.com> Reviewed-by:
-
Trent Piepho authored
Insure property is in valid range and fail when reading DT if it is not. Also add error message for existing failure if required property is not present. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Trent Piepho authored
The driver would only set the IO impedance value when RGMII internal delays were enabled. There is no reason for this. Move the IO impedance block out of the RGMII delay block. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Trent Piepho authored
The variables used to store u32 DT properties were signed ints. This doesn't work properly if the value of the property were to overflow. Use unsigned variables so this doesn't happen. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Trent Piepho authored
The code was assuming the reset default of the delay control register was to have delay disabled. This is what the datasheet shows as the register's initial value. However, that's not actually true: the default is controlled by the PHY's pin strapping. If the interface mode is selected as RX or TX delay only, insure the other direction's delay is disabled. If the interface mode is just "rgmii", with neither TX or RX internal delay, one might expect that the driver should disable both delays. But this is not what the driver does. It leaves the setting at the PHY's strapping's default. And that default, for no pins with strapping resistors, is to have delay enabled and 2.00 ns. Rather than change this behavior, I've kept it the same and documented it. No delay will most likely not work and will break ethernet on any board using "rgmii" mode. If the board is strapped to have a delay and is configured to use "rgmii" mode a warning is generated that "rgmii-id" should have been used. Also validate the delay values and fail if they are not in range. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Trent Piepho authored
Generally, the output clock pin is only used for testing and only serves as a source of RF noise after this. It could be used to daisy-chain PHYs, but this is uncommon. Since the PHY can disable the output, make doing so an option. I do this by adding another enumeration to the allowed values of ti,clk-output-sel. The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might expect: to select the REF_CLK as the output. Rather it meant "keep clock output setting as is", which, depending on PHY strapping, might not be outputting REF_CLK. Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output. Omitting the property will leave the setting as is (which was the previous behavior in this case). Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Trent Piepho authored
The clock output is generally only used for testing and development and not used to daisy-chain PHYs. It's just a source of RF noise afterward. Add a mux value for "off". I've added it as another enumeration to the output property. In the actual PHY, the mux and the output enable are independently controllable. However, it doesn't seem useful to be able to describe the mux setting when the output is disabled. Document that PHY's default setting will be left as is if the property is omitted. Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Trent Piepho authored
Add a note to make it more clear how the driver behaves when "rgmii" vs "rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected. Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Vishal Kulkarni authored
Hash (exact-match) filters used for offloading flows share the same active region resources on the chip with upper layer drivers, like iw_cxgb4, chcr, etc. Currently, only either Hash filters or ULDs can use the active region resources, but not both. Hence, use the new firmware configuration parameters (when available) to allow both the Hash filters and ULDs to share the active region simultaneously. Signed-off-by:
Vishal Kulkarni <vishal@chelsio.com> Signed-off-by:
-
Baruch Siach authored
Don't disable the ipg clock in the regulator error path. The clock is disable unconditionally two lines below the failed_regulator label. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
- 22 May, 2019 6 commits
-
-
Felipe Gasper authored
This adds the ability for Netlink to report a socket's UID along with the other UNIX diagnostic information that is already available. This will allow diagnostic tools greater insight into which users control which socket. To test this, do the following as a non-root user: unshare -U -r bash nc -l -U user.socket.$$ & .. and verify from within that same session that Netlink UNIX socket diagnostics report the socket's UID as 0. Also verify that Netlink UNIX socket diagnostics report the socket's UID as the user's UID from an unprivileged process in a different session. Verify the same from a root process. Signed-off-by:Felipe Gasper <felipe@felipegasper.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Will Deacon: - Fix SPE probe failure when backing auxbuf with high-order pages - Fix handling of DMA allocations from outside of the vmalloc area - Fix generation of build-id ELF section for vDSO object - Disable huge I/O mappings if kernel page table dumping is enabled - A few other minor fixes (comments, kconfig etc) * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: vdso: Explicitly add build-id option arm64/mm: Inhibit huge-vmap with ptdump arm64: Print physical address of page table base in show_pte() arm64: don't trash config with compat symbol if COMPAT is disabled arm64: assembler: Update comment above cond_yield_neon() macro drivers/perf: arm_spe: Don't error on high-order pages for aux buf arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
-
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2Linus Torvalds authored
Pull gfs2 fix from Andreas Gruenbacher: "Fix a gfs2 sign extension bug introduced in v4.3" * tag 'gfs2-5.1.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: gfs2: Fix sign extension bug in gfs2_update_stats
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Clear up some recent tipc regressions because of registration ordering. Fix from Junwei Hu. 2) tipc's TLV_SET() can read past the end of the supplied buffer during the copy. From Chris Packham. 3) ptp example program doesn't match the kernel, from Richard Cochran. 4) Outgoing message type fix in qrtr, from Bjorn Andersson. 5) Flow control regression in stmmac, from Tan Tee Min. 6) Fix inband autonegotiation in phylink, from Russell King. 7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning. 8) Fix usbnet crash after disconnect, from Kloetzke Jan. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits) usbnet: fix kernel crash after disconnect selftests: fib_rule_tests: use pre-defined DEV_ADDR net-next: net: Fix typos in ip-sysctl.txt ipv6: Consider sk_bound_dev_if when binding a raw socket to an address net: phylink: ensure inband AN works correctly usbnet: ipheth: fix racing condition net: stmmac: dma channel control register need to be init first net: stmmac: fix ethtool flow control not able to get/set net: qrtr: Fix message type of outgoing packets networking: : fix typos in code comments ptp: Fix example program to match kernel. fddi: fix typos in code comments selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test selftests: fib_rule_tests: fix local IPv4 address typo tipc: Avoid copying bytes beyond the supplied data 2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function 1/2] net: axienet: use readx_poll_timeout() in mdio wait function vlan: Mark expected switch fall-through macvlan: Mark expected switch fall-through net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query ... -
Linus Torvalds authored
Merge tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fix from Mike Snitzer: "Fix a particularly glaring oversight in a DM core commit from 5.1 that doesn't properly trim special IOs (e.g. discards) relative to corresponding target's max_io_len_target_boundary()" * tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm: make sure to obey max_io_len_target_boundary
-
Andreas Gruenbacher authored
Commit 4d207133 changed the types of the statistic values in struct gfs2_lkstats from s64 to u64. Because of that, what should be a signed value in gfs2_update_stats turned into an unsigned value. When shifted right, we end up with a large positive value instead of a small negative value, which results in an incorrect variance estimate. Fixes: 4d207133 ("gfs2: Make statistics unsigned, suitable for use with do_div()") Signed-off-by:
Andreas Gruenbacher <agruenba@redhat.com> Cc: stable@vger.kernel.org # v4.4+
-
- 21 May, 2019 21 commits
-
-
Michael Lass authored
Commit 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM target interface") incorrectly removed code from __send_changing_extent_only() that is required to impose a per-target IO boundary on IO that exceeds max_io_len_target_boundary(). Otherwise "special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond where allowed. Fix this by restoring the max_io_len_target_boundary() limit in __send_changing_extent_only() Fixes: 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM target interface") Cc: stable@vger.kernel.org # 5.1+ Signed-off-by:
Michael Lass <bevan@bi-co.net> Signed-off-by:
Mike Snitzer <snitzer@redhat.com>
-
Kloetzke Jan authored
When disconnecting cdc_ncm the kernel sporadically crashes shortly after the disconnect: [ 57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000 ... [ 58.006653] PC is at 0x0 [ 58.009202] LR is at call_timer_fn+0xec/0x1b4 [ 58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145 [ 58.020976] sp : ffffff8008003da0 [ 58.024295] x29: ffffff8008003da0 x28: 0000000000000001 [ 58.029618] x27: 000000000000000a x26: 0000000000000100 [ 58.034941] x25: 0000000000000000 x24: ffffff8008003e68 [ 58.040263] x23: 0000000000000000 x22: 0000000000000000 [ 58.045587] x21: 0000000000000000 x20: ffffffc68fac1808 [ 58.050910] x19: 0000000000000100 x18: 0000000000000000 [ 58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10 [ 58.061556] x15: 0000000000000001 x14: 000000000000006e [ 58.066878] x13: 0000000000000000 x12: 00000000000000ba [ 58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020 [ 58.077524] x9 : 8000100008001000 x8 : 0000000000000001 [ 58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70 [ 58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b [ 58.093492] x3 : 0000000000000000 x2 : 0000000000000000 [ 58.098814] x1 : 0000000000000000 x0 : 0000000000000000 ... [ 58.205800] [< (null)>] (null) [ 58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c [ 58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128 [ 58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348 [ 58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc [ 58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac [ 58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac ... The crash happens roughly 125..130ms after the disconnect. This correlates with the 'delay' timer that is started on certain USB tx/rx errors in the URB completion handler. The problem is a race of usbnet_stop() with usbnet_start_xmit(). In usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in flight. This only makes sense if no new URBs are submitted concurrently, though. But the usbnet_start_xmit() can run at the same time on another CPU which almost unconditionally submits an URB. The error callback of the new URB will then schedule the timer after it was already stopped. The fix adds a check if the tx queue is stopped after the tx list lock has been taken. This should reliably prevent the submission of new URBs while usbnet_terminate_urbs() does its job. The same thing is done on the rx side even though it might be safe due to other flags that are checked there. Signed-off-by:
Jan Klötzke <Jan.Kloetzke@preh.de> Signed-off-by:
-
Hangbin Liu authored
DEV_ADDR is defined but not used. Use it in address setting. Do the same with IPv6 for consistency. Reported-by:
David Ahern <dsahern@gmail.com> Fixes: fc82d93e ("selftests: fib_rule_tests: fix local IPv4 address typo") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Masanari Iida authored
This patch fixes some spelling typos found in ip-sysctl.txt Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
-
Mike Manning authored
IPv6 does not consider if the socket is bound to a device when binding to an address. The result is that a socket can be bound to eth0 and then bound to the address of eth1. If the device is a VRF, the result is that a socket can only be bound to an address in the default VRF. Resolve by considering the device if sk_bound_dev_if is set. Signed-off-by:
Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by:
-
Russell King authored
Do not update the link interface mode while the link is down to avoid spurious link interface changes. Always call mac_config if we have a PHY to propagate the pause mode settings to the MAC. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Bernd Eckstein authored
Fix a racing condition in ipheth.c that can lead to slow performance. Bug: In ipheth_tx(), netif_wake_queue() may be called on the callback ipheth_sndbulk_callback(), _before_ netif_stop_queue() is called. When this happens, the queue is stopped longer than it needs to be, thus reducing network performance. Fix: Move netif_stop_queue() in front of usb_submit_urb(). Now the order is always correct. In case, usb_submit_urb() fails, the queue is woken up again as callback will not fire. Testing: This racing condition is usually not noticeable, as it has to occur very frequently to slowdown the network. The callback from the USB is usually triggered slow enough, so the situation does not appear. However, on a Ubuntu Linux on VMWare Workstation, running on Windows 10, the we loose the race quite often and the following speedup can be noticed: Without this patch: Download: 4.10 Mbit/s, Upload: 4.01 Mbit/s With this patch: Download: 36.23 Mbit/s, Upload: 17.61 Mbit/s Signed-off-by:
Oliver Zweigle <Oliver.Zweigle@faro.com> Signed-off-by:
Bernd Eckstein <3ernd.Eckstein@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinuxLinus Torvalds authored
Pull SELinux fix from Paul Moore: "One small SELinux patch to fix a problem when disconnecting a SCTP socket with connect(AF_UNSPEC)" * tag 'selinux-pr-20190521' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux: selinux: do not report error on connect(AF_UNSPEC)
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-coreLinus Torvalds authored
Pull SPDX update from Greg KH: "Here is a series of patches that add SPDX tags to different kernel files, based on two different things: - SPDX entries are added to a bunch of files that we missed a year ago that do not have any license information at all. These were either missed because the tool saw the MODULE_LICENSE() tag, or some EXPORT_SYMBOL tags, and got confused and thought the file had a real license, or the files have been added since the last big sweep, or they were Makefile/Kconfig files, which we didn't touch last time. - Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan tools can determine the license text in the file itself. Where this happens, the license text is removed, in order to cut down on the 700+ different ways we have in the kernel today, in a quest to get rid of all of these. These patches have been out for review on the linux-spdx@vger mailing list, and while they were created by automatic tools, they were hand-verified by a bunch of different people, all whom names are on the patches are reviewers. The reason for these "large" patches is if we were to continue to progress at the current rate of change in the kernel, adding license tags to individual files in different subsystems, we would be finished in about 10 years at the earliest. There will be more series of these types of patches coming over the next few weeks as the tools and reviewers crunch through the more "odd" variants of how to say "GPLv2" that developers have come up with over the years, combined with other fun oddities (GPL + a BSD disclaimer?) that are being unearthed, with the goal for the whole kernel to be cleaned up. These diffstats are not small, 3840 files are touched, over 10k lines removed in just 24 patches" * tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits) treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3 ... -
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fixes from Herbert Xu: - Two long-standing bugs in the powerpc assembly of vmx - Stack overrun caused by HASH_MAX_DESCSIZE being too small - Regression in caam * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: vmx - ghash: do nosimd fallback manually crypto: vmx - CTR: always increment IV as quadword crypto: hash - fix incorrect HASH_MAX_DESCSIZE crypto: caam - fix typo in i.MX6 devices list for errata
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it would be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 6 file(s). Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Steve Winslow <swinslow@gmail.com> Reviewed-by:
Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by:
Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by:
Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154043.007767574@linutronix.deSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 50 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this software may be redistributed and or modified under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 2 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): the code contained herein is licensed under the gnu general public license you may obtain a copy of the gnu general public license version 2 or later at the following locations extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 4 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 2 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program see the file copying if not write to the free software foundation inc 51 franklin steet fifth floor boston ma 02110 1301 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 41 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation 51 franklin street fifth floor boston ma 02110 1301 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 2 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program see the file copying if not write to the free software foundation 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 52 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not see http www gnu org licenses extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 13 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not see http www gnu org licenses the full gnu general public license is included in this distribution in the file called copying extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 9 file(s). Signed-off-by:
-
Thomas Gleixner authored
Based on 1 normalized pattern(s): gnu cc is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 or at your option any later version gnu cc is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with gnu cc see the file copying if not write to the free software foundation 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3 file(s). Signed-off-by:
-
