Eric noticed that __ipv6_ifa_notify is called under rcu_read_lock, so
the gfp argument to addrconf_prefix_route can not be GFP_KERNEL.

While scrubbing other calls I noticed addrconf_addr_gen has one
place with GFP_ATOMIC that can be GFP_KERNEL.

Fixes: acb54e3c ("net/ipv6: Add gfp_flags to route add functions")
Reported-by: syzbot+2add39b05179b31f912f@syzkaller.appspotmail.com
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib6_idev can be obtained from __in6_dev_get on the nexthop device
rather than caching it in the fib6_info. Remove it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After 4832c30d ("net: ipv6: put host and anycast routes on device
with address") the comparison of idev does not add value since it
correlates to the nexthop device which is already compared. Remove
the idev comparison.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to 4832c30d ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.

Commit 4832c30d changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change ip6_route_get_saddr can just pass the nexthop
device to ipv6_dev_get_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to 4832c30d ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.

Commit 4832c30d changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change a couple of device checks during route lookups
are no longer needed. Remove them.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aca_idev has only 1 user - inet6_fill_ifacaddr - and it only
wants the device index which can be extracted from the fib6_info
nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

addrconf_dst_alloc now returns a fib6_info. Update the name
and its users to reflect the change.

Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.

Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After working on IP defragmentation lately, I found that some large
packets defeat CHECKSUM_COMPLETE optimization because of NIC adding
zero paddings on the last (small) fragment.

While removing the padding with pskb_trim_rcsum(), we set skb->ip_summed
to CHECKSUM_NONE, forcing a full csum validation, even if all prior
fragments had CHECKSUM_COMPLETE set.

We can instead compute the checksum of the part we are trimming,
usually smaller than the part we keep.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tracking TCP data delivery and ECN stats

This patch series improve tracking the data delivery status
  1. minor improvement on SYN data
  2. accounting bytes delivered with CE marks
  3. exporting the delivery stats to applications

s.t. users can get better sense of TCP performance at per host,
per connection, and even per application message level.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Export data delivered and delivered with CE marks to
1) SNMP TCPDelivered and TCPDeliveredCE
2) getsockopt(TCP_INFO)
3) Timestamping API SOF_TIMESTAMPING_OPT_STATS

Note that for SCM_TSTAMP_ACK, the delivery info in
SOF_TIMESTAMPING_OPT_STATS is reported before the info
was fully updated on the ACK.

These stats help application monitor TCP delivery and ECN status
on per host, per connection, even per message level.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new delivered_ce stat in tcp socket to estimate
number of packets being marked with CE bits. The estimation is
done via ACKs with ECE bit. Depending on the actual receiver
behavior, the estimation could have biases.

Since the TCP sender can't really see the CE bit in the data path,
so the sender is technically counting packets marked delivered with
the "ECE / ECN-Echo" flag set.

With RFC3168 ECN, because the ECE bit is sticky, this count can
drastically overestimate the nummber of CE-marked data packets

With DCTCP-style ECN this should be reasonably precise unless there
is loss in the ACK path, in which case it's not precise.

With AccECN proposal this can be made still more precise, even in
the case some degree of ACK loss.

However this is sender's best estimate of CE information.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new helper tcp_newly_delivered() to prepare the ECN accounting change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the tcp_sock:delivered has inconsistent accounting for SYN and FIN.
1. it counts pure FIN
2. it counts pure SYN
3. it counts SYN-data twice
4. it does not count SYN-ACK

For congestion control perspective it does not matter much as C.C. only
cares about the difference not the aboslute value. But the next patch
would export this field to user-space so it's better to report the absolute
value w/o these caveats.

This patch counts SYN, SYN-ACK, or SYN-data delivery once always in
the "delivered" field.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lockdep does not know that the locks used by IPv4 defrag
and IPv6 reassembly units are of different classes.

It complains because of following chains :

1) sch_direct_xmit()        (lock txq->_xmit_lock)
    dev_hard_start_xmit()
     xmit_one()
      dev_queue_xmit_nit()
       packet_rcv_fanout()
        ip_check_defrag()
         ip_defrag()
          spin_lock()     (lock frag queue spinlock)

2) ip6_input_finish()
    ipv6_frag_rcv()       (lock frag queue spinlock)
     ip6_frag_queue()
      icmpv6_param_prob() (lock txq->_xmit_lock at some point)

We could add lockdep annotations, but we also can make sure IPv6
calls icmpv6_param_prob() only after the release of the frag queue spinlock,
since this naturally makes frag queue spinlock a leaf in lock hierarchy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.

The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.

In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.

The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.

Also requires exporting dev_set_alias in netdev core.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with further smaller improvements

This series includes further smaller improvements.

Then I think the basic cleanup has been done and next step would be
preparing the switch to phylib.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.

By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000

In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For security reasons since commit ad67b74d "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code can be simplified by changing the argument type of hw_start
callbacks from struct net_device * to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is very simple and used only once, so we can inline
the two statements.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.

When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8169_rx_fill() is called only once and directly before the call
array tp->Rx_databuff[] is filled with zero's. Therefore we don't
need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_schedule() is called from hard irq context, so we can switch to
napi_schedule_irqoff() and avoid some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can use generic constant NAPI_POLL_WAIT instead of defining an own
constant for the same value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not a giant leap for mankind, but let's avoid the open-coded memcpy
and use standard helper skb_copy_to_linear_data instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 6f0333b8 "r8169: use 50% less ram for RX ring" member
align isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Member features of struct rtl8169_private isn't used any longer since
commit 6c6aa15f "r8169: improve interrupt handling", so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Murali Karicheri says:

====================
Add support for netcp driver on K2G SoC

K2G SoC is another variant of Keystone family of SoCs. This patch
series add support for NetCP driver on this SoC. The QMSS found on
K2G SoC is a cut down version of the QMSS found on other keystone
devices with less number of queues, internal link ram etc. The patch
series has 2 patch sets that goes into the drivers/soc and the
rest has to be applied to net sub system. Please review and merge
if this looks good.

K2G TRM is located at http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Thanks

The boot logs on K2G ICE board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/yvZ6drFhkW/

The boot logs on K2G GP board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/QTr6K7s4Zp/

Also regressed boot on K2HK and K2L EVMs as we have modified GBE
version detection logic (K2E uses same version of NetCP as in K2L.
So regression on one of them is needed).

Boot log on K2L and K2HK EVMs are at
https://pastebin.ubuntu.com/p/N9DBdPjbvR/

This series applies to net-next master branch.

Change history:
  v4 - ready for merge to net-next
       Folded the series "Add promiscous mode support in k2g network driver"
       into this.
       Fixed a typo in 5/11 (sgmii to rgmii) based on TI internal comment
       Reworked 4/11 and title changed to reflect additional changes to
       exclude sgmii configuration code for 2U cpsw. Use IS_SS_ID_2U()
       macro for customization.
       Added Reviewed-by from Rob Herring against 1/13
  v3 - Addressed comments from Andrew Lunn and Grygorii Strashko
       against v2.
  v2 - Addressed following comments on initial version
       - split patch 3/5 to multiple patches from Andrew Lunn
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>