The "mediatek,drive-strength-adv" pin config property has been
deprecated in favor of the generic "drive-strength-microamp" property.

Drop or convert all instances. A value of 0 disables the advanced
mode, which is the hardware default.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240412075516.1199846-1-wenst@chromium.orgSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

The "output-enable" property is set on uart1's RTS pin. This is bogus
because the hardware does not actually have a controllable output
buffer. Secondly, the implementation incorrectly treats this property
as a request to switch the pin to GPIO output. This does not fit the
intended semantic of "output-enable" and it does not have any affect
either because the pin is muxed to the UART function, not the GPIO
function.

Drop the property.

Fixes: cd894e27 ("arm64: dts: mt8183: Add krane-sku176 board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240412075613.1200048-1-wenst@chromium.orgSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Add the necessary power supplies to safely enable CPU and GPU frequency
scaling.

Link: https://lore.kernel.org/r/20240409114211.310462-6-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Enable the PCIe0 PHY to be able to set calibrations read from eFuses,
improving the stability and performance of the PCIe link.

While at it, also enable the T-PHYs for both PCIe1 and for USB, allowing
the USB ports to finally switch to gadget mode if needed, and configure
the VBUS/ID pins of both USB ports for the same.

Link: https://lore.kernel.org/r/20240409114211.310462-5-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

The paris pinctrl driver supports specifying the RSEL drive strength
in microamperes as well as internal bits definitions: choose to specify
those in uA to avoid using hardware specific values in device trees.

Link: https://lore.kernel.org/r/20240409114211.310462-4-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

GPIOs 25 and 26 do not support pull-up/pull-down when those are muxed
as I2C6's SDA6/SCL6 lines: set those to bias-disable to avoid warning
messages from the pinctrl driver.

Fixes: 96564b1e ("arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board")
Link: https://lore.kernel.org/r/20240409114211.310462-3-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

The thermal zones in MT8183 had cryptic names and all of them, apart
from the cpu-thermal zone, had no thermal trips, hence those were not
probed at all.

Refactor the tzts1..5 and tztsABB thermal zones to add the correct
thermal trips and give them a meaningful name, corresponding to the
actually monitored thermal zone.
While at it, also rename the thermal sensor node to "thermal-sensor".

Now the thermal zones are probing and their temperatures can be read.

Fixes: b325ce39 ("arm64: dts: mt8183: add thermal zone node")
Link: https://lore.kernel.org/r/20240410083002.1357857-4-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

This SoC has two GPU related thermal zones: the primary zone must be
called "gpu-thermal" for SVS to pick it up.

Fixes: c7a72805 ("arm64: dts: mediatek: mt8192: Add thermal nodes and thermal zones")
Link: https://lore.kernel.org/r/20240410083002.1357857-3-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

This SoC has two GPU related thermal zones: the primary zone must be
called "gpu-thermal" for SVS to pick it up.

Fixes: 1e5b6725 ("arm64: dts: mediatek: mt8195: Add AP domain thermal zones")
Link: https://lore.kernel.org/r/20240410083002.1357857-2-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.

The Genio 700 EVK has following features:

- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
  - M.2 Key B slot
  - Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-2-macpaul.lin@mediatek.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

1. Add compatible for MT8390.
2. Add bindings for the MediaTek mt8390-evk board, also known
as the "Genio 700-EVK".

The MT8390 and MT8188 belong to the same SoC family,
with only minor differences in their physical characteristics.
They utilize unique efuse values for differentiation.

The booting process and configurations are managed by boot
loaders, firmware, and TF-A. Consequently, the part numbers
and procurement channels vary.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-1-macpaul.lin@mediatek.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

MT7981 (Filogic 820) is a low cost version of MT7986 (Filogic 830) with
the same watchdog controller. It also comes with on-SoC 802.11ax
wireless.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240221085547.27840-1-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Add bindings of two on-SoC XHCI controllers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213130044.1976-2-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Add compatible for MT8188 VPP mutex, having different bits to activate
mute for various hardware IPs.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240322092845.381313-2-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

None of the MT8192 Chromebooks had their chassis-type specified: add
the right definition for each.
Reviewed-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20240313141538.1438167-3-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Define the chassis type on the remaining MT8183 Chromebooks.

Link: https://lore.kernel.org/r/20240313141538.1438167-2-angelogioacchino.delregno@collabora.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Introduce the Airoha EN7581 SoC's dtsi and the Airoha EN7581 Evaluation
Board's dts file, as well as the required Makefiles.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/f05a36dd7e8ef34ead8a63aa10fcffb542229404.1709975956.git.lorenzo@kernel.orgSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Introduce Airoha EN7581 entry in Airoha dts binding.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/ee9cda964dac62d38d1c239f7b189f707d3708a0.1709975956.git.lorenzo@kernel.orgSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router. It
has 256 MiB of RAM, some LEDs & buttons and (not described yet) 4
Ethernet ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-5-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

MT7981 contains on-SoC PIN controller that is also a GPIO provider.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-4-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-3-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Cudy is a Chinese company providing networking products.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-2-zajec5@gmail.comSigned-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.

This fixes a randconfig build error on mips:

  include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
  include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc2 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tool fix from Arnaldo Carvalho de Melo:
 "Revert a patch causing a regression.

  This made a simple 'perf record -e cycles:pp make -j199' stop working
  on the Ampere ARM64 system Linus uses to test ARM64 kernels".

* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"

This reverts commit 617824a7.

This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.

The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Ethan Adams <j.ethan.adams@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tycho Andersen <tycho@tycho.pizza>
Cc: Yang Jihong <yangjihong@bytedance.com>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull smb client fixes from Steve French:

 - two important netfs integration fixes - including for a data
   corruption and also fixes for multiple xfstests

 - reenable swap support over SMB3

* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Fix missing set of remote_i_size
  cifs: Fix smb3_insert_range() to move the zero_point
  cifs: update internal version number
  smb3: reenable swapfiles over SMB3 mounts

Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull misc fixes from Andrew Morton:
 "16 hotfixes, 11 of which are cc:stable.

  A few nilfs2 fixes, the remainder are for MM: a couple of selftests
  fixes, various singletons fixing various issues in various parts"

* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  mm/ksm: fix possible UAF of stable_node
  mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
  mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
  nilfs2: fix potential hang in nilfs_detach_log_writer()
  nilfs2: fix unexpected freezing of nilfs_segctor_sync()
  nilfs2: fix use-after-free of timer for log writer thread
  selftests/mm: fix build warnings on ppc64
  arm64: patching: fix handling of execmem addresses
  selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
  selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
  selftests/mm: compaction_test: fix bogus test success on Aarch64
  mailmap: update email address for Satya Priya
  mm/huge_memory: don't unpoison huge_zero_folio
  kasan, fortify: properly rename memintrinsics
  lib: add version into /proc/allocinfo output
  mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL

Pull irq fixes from Ingo Molnar:

 - Fix x86 IRQ vector leak caused by a CPU offlining race

 - Fix build failure in the riscv-imsic irqchip driver
   caused by an API-change semantic conflict

 - Fix use-after-free in irq_find_at_or_after()

* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
  genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
  irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict

Pull x86 fixes from Ingo Molnar:

 - Fix regressions of the new x86 CPU VFM (vendor/family/model)
   enumeration/matching code

 - Fix crash kernel detection on buggy firmware with
   non-compliant ACPI MADT tables

 - Address Kconfig warning

* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
  crypto: x86/aes-xts - switch to new Intel CPU model defines
  x86/topology: Handle bogus ACPI tables correctly
  x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y

Pull ipmi updates from Corey Minyard:
 "Mostly updates for deprecated interfaces, platform.remove and
  converting from a tasklet to a BH workqueue.

  Also use HAS_IOPORT for disabling inb()/outb()"

* tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi:
  ipmi: kcs_bmc_npcm7xx: Convert to platform remove callback returning void
  ipmi: kcs_bmc_aspeed: Convert to platform remove callback returning void
  ipmi: ipmi_ssif: Convert to platform remove callback returning void
  ipmi: ipmi_si_platform: Convert to platform remove callback returning void
  ipmi: ipmi_powernv: Convert to platform remove callback returning void
  ipmi: bt-bmc: Convert to platform remove callback returning void
  char: ipmi: handle HAS_IOPORT dependencies
  ipmi: Convert from tasklet to BH workqueue

Pull ceph updates from Ilya Dryomov:
 "A series from Xiubo that adds support for additional access checks
  based on MDS auth caps which were recently made available to clients.

  This is needed to prevent scenarios where the MDS quietly discards
  updates that a UID-restricted client previously (wrongfully) acked to
  the user.

  Other than that, just a documentation fixup"

* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
  doc: ceph: update userspace command to get CephFS metadata
  ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
  ceph: check the cephx mds auth access for async dirop
  ceph: check the cephx mds auth access for open
  ceph: check the cephx mds auth access for setattr
  ceph: add ceph_mds_check_access() helper
  ceph: save cap_auths in MDS client when session is opened

Pull ntfs3 updates from Konstantin Komarov:
 "Fixes:
   - reusing of the file index (could cause the file to be trimmed)
   - infinite dir enumeration
   - taking DOS names into account during link counting
   - le32_to_cpu conversion, 32 bit overflow, NULL check
   - some code was refactored

  Changes:
   - removed max link count info display during driver init

  Remove:
   - atomic_open has been removed for lack of use"

* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
  fs/ntfs3: Break dir enumeration if directory contents error
  fs/ntfs3: Fix case when index is reused during tree transformation
  fs/ntfs3: Mark volume as dirty if xattr is broken
  fs/ntfs3: Always make file nonresident on fallocate call
  fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
  fs/ntfs3: Use variable length array instead of fixed size
  fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
  fs/ntfs3: Check 'folio' pointer for NULL
  fs/ntfs3: Missed le32_to_cpu conversion
  fs/ntfs3: Remove max link count info display during driver init
  fs/ntfs3: Taking DOS names into account during link counting
  fs/ntfs3: remove atomic_open
  fs/ntfs3: use kcalloc() instead of kzalloc()

Pull smb server fixes from Steve French:
 "Two ksmbd server fixes, both for stable"

* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: ignore trailing slashes in share paths
  ksmbd: avoid to send duplicate oplock break notifications

Pull RTC updates from Alexandre Belloni:
 "There is one new driver and then most of the changes are the device
  tree bindings conversions to yaml.

  New driver:
   - Epson RX8111

  Drivers:
   - Many Device Tree bindings conversions to dtschema
   - pcf8563: wakeup-source support"

* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  pcf8563: add wakeup-source support
  rtc: rx8111: handle VLOW flag
  rtc: rx8111: demote warnings to debug level
  rtc: rx6110: Constify struct regmap_config
  dt-bindings: rtc: convert trivial devices into dtschema
  dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
  dt-bindings: rtc: pxa-rtc: convert to dtschema
  rtc: Add driver for Epson RX8111
  dt-bindings: rtc: Add Epson RX8111
  rtc: mcp795: drop unneeded MODULE_ALIAS
  rtc: nuvoton: Modify part number value
  rtc: test: Split rtc unit test into slow and normal speed test
  dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
  dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
  dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
  dt-bindings: rtc: armada-380-rtc: convert to dtschema
  rtc: cros-ec: provide ID table for avoiding fallback match

Pull i3c updates from Alexandre Belloni:
 "Runtime PM (power management) is improved and hot-join support has
  been added to the dw controller driver.

  Core:
   - Allow device driver to trigger controller runtime PM

  Drivers:
   - dw: hot-join support
   - svc: better IBI handling"

* tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  i3c: dw: Add hot-join support.
  i3c: master: Enable runtime PM for master controller
  i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
  i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame
  i3c: Add comment for -EAGAIN in i3c_device_do_priv_xfers()

Pull jffs2 updates from Richard Weinberger:

 - Fix illegal memory access in jffs2_free_inode()

 - Kernel-doc fixes

 - print symbolic error names

* tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  jffs2: Fix potential illegal address access in jffs2_free_inode
  jffs2: Simplify the allocation of slab caches
  jffs2: nodemgmt: fix kernel-doc comments
  jffs2: print symbolic error name instead of error code

Pull UML updates from Richard Weinberger:

 - Fixes for -Wmissing-prototypes warnings and further cleanup

 - Remove callback returning void from rtc and virtio drivers

 - Fix bash location

* tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (26 commits)
  um: virtio_uml: Convert to platform remove callback returning void
  um: rtc: Convert to platform remove callback returning void
  um: Remove unused do_get_thread_area function
  um: Fix -Wmissing-prototypes warnings for __vdso_*
  um: Add an internal header shared among the user code
  um: Fix the declaration of kasan_map_memory
  um: Fix the -Wmissing-prototypes warning for get_thread_reg
  um: Fix the -Wmissing-prototypes warning for __switch_mm
  um: Fix -Wmissing-prototypes warnings for (rt_)sigreturn
  um: Stop tracking host PID in cpu_tasks
  um: process: remove unused 'n' variable
  um: vector: remove unused len variable/calculation
  um: vector: fix bpfflash parameter evaluation
  um: slirp: remove set but unused variable 'pid'
  um: signal: move pid variable where needed
  um: Makefile: use bash from the environment
  um: Add winch to winch_handlers before registering winch IRQ
  um: Fix -Wmissing-prototypes warnings for __warp_* and foo
  um: Fix -Wmissing-prototypes warnings for text_poke*
  um: Move declarations to proper headers
  ...

Pull drm fixes from Dave Airlie:
 "Some fixes for the end of the merge window, mostly amdgpu and panthor,
  with one nouveau uAPI change that fixes a bad decision we made a few
  months back.

  nouveau:
   - fix bo metadata uAPI for vm bind

  panthor:
   - Fixes for panthor's heap logical block.
   - Reset on unrecoverable fault
   - Fix VM references.
   - Reset fix.

  xlnx:
   - xlnx compile and doc fixes.

  amdgpu:
   - Handle vbios table integrated info v2.3

  amdkfd:
   - Handle duplicate BOs in reserve_bo_and_cond_vms
   - Handle memory limitations on small APUs

  dp/mst:
   - MST null deref fix.

  bridge:
   - Don't let next bridge create connector in adv7511 to make probe
     work"

* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
  drm/amdgpu/atomfirmware: add intergrated info v2.3 table
  drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
  drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
  drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
  drm/bridge: adv7511: Attach next bridge without creating connector
  drm/buddy: Fix the warn on's during force merge
  drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
  drm/panthor: Call panthor_sched_post_reset() even if the reset failed
  drm/panthor: Reset the FW VM to NULL on unplug
  drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
  drm/panthor: Force an immediate reset on unrecoverable faults
  drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
  drm/panthor: Fix an off-by-one in the heap context retrieval logic
  drm/panthor: Relax the constraints on the tiler chunk size
  drm/panthor: Make sure the tiler initial/max chunks are consistent
  drm/panthor: Fix tiler OOM handling to allow incremental rendering
  drm: xlnx: zynqmp_dpsub: Fix compilation error
  drm: xlnx: zynqmp_dpsub: Fix few function comments

Occasionally, the generic/001 xfstest will fail indicating corruption in
one of the copy chains when run on cifs against a server that supports
FSCTL_DUPLICATE_EXTENTS_TO_FILE (eg. Samba with a share on btrfs).  The
problem is that the remote_i_size value isn't updated by cifs_setsize()
when called by smb2_duplicate_extents(), but i_size *is*.

This may cause cifs_remap_file_range() to then skip the bit after calling
->duplicate_extents() that sets sizes.

Fix this by calling netfs_resize_file() in smb2_duplicate_extents() before
calling cifs_setsize() to set i_size.

This means we don't then need to call netfs_resize_file() upon return from
->duplicate_extents(), but we also fix the test to compare against the pre-dup
inode size.

[Note that this goes back before the addition of remote_i_size with the
netfs_inode struct.  It should probably have been setting cifsi->server_eof
previously.]

Fixes: cfc63fc8 ("smb3: fix cached file size problems in duplicate extents (reflink)")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
Signed-off-by: Steve French <stfrench@microsoft.com>