The HWMP sequence number of received RANN element is compared to decide whether to be
propagated. The sequence number is required to covert from 32bit little endian data into
CPUs endianness for comparison. The same applies to the RANN metric.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When receiving DTIM we currently disable power save mode in the
hardware unconditionally, i.e. also when the hardware was not sleeping.
This causes trouble with at least one wireless chipset (Ralink RT3572).
When the hardware is not sleeping and we send a wakeup command (e.g.
this happens after a scan) then a significant decrease of the link
quality or a disconnect may occur.
Disabling power save mode only when it was enabled prevents this issue.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Calling mod_timer from the rx/tx hotpath is somewhat expensive, and the
timeout doesn't need to be so precise.

Switch to a different strategy: Schedule the timer initially, store jiffies
of all last rx/tx activity which would previously modify the timer, and
let the timer re-arm itself after checking the last rx/tx timestamp.
Make the session timers deferrable to avoid causing extra wakeups on systems
running on battery.
This visibly reduces CPU load under high network load on small embedded
systems.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With 9-letter driver names phy's number was truncated
to two characters, which caused warnings when creating
sysfs entries for leds on systems with multiple devices.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use a temporary to make the code a bit neater.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the normal kernel facilities and use %pM
to print the all zero mac address.

Remove unnecessary line continuation.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry.Finger@lwfinger.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers that load firmware from their probe routine have problems with
the latest versions of udev as they get timeouts while waiting for user
space to start. The problem is fixed by using request_firmware_nowait()
and delaying the start of mac80211 until the firmware is loaded.

To prevent the possibility of the driver being unloaded while the
firmware loading callback is still active, a completion queue entry
is used.

Also, to simplify the firmware loading procedure, this patch removes
the old, unofficial and confusing fallback firmware names. However,
they are still supported! So any user - who is still using them -
is hereby advised to link/rename their old firmware filenames:
	isl3890usb to isl3886usb
	isl3887usb_bare to isl3887usb
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54_unregister_common may now be called by the backend
driver's remove routine, even if the ieee80211_hw device
struct was never successfully registered.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In this handler LOW_RSSI and HIGH_RSSI events are subscribed
to FW using provided threshold value so that FW will monitor
connection quality and trigger any of these events.

Driver will notify cfg80211 about connection quality based on
inputs from FW and provided hysteresis.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds the support for updating average signal information
in dump_station().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) The wrapper function mwifiex_get_signal_info() is unnecessary.
2) As noise and signal vaules in private structure already get
modified, we don't need to explicitly pass
"struct mwifiex_ds_get_signal" to get it filled.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This enables user to dump station information using
"iw dev <devname> station dump" command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During wiphy registration signal_type is initialized to
CFG80211_SIGNAL_TYPE_MBM. So convert signal strength from dBm to
mBm. Also, the value is absolute. Make it negative before
sending to cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This lets the user know which interface has failed
the check_sdata_in_driver check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.

Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sometimes the probe frame (nullfunc) is stuck at the hw queue. so that
the mac80211 terminates the connection as it wont see the tx status.
Instead of waiting for long period for ack status, lets call flush
to get nullfunc status immediately. It also helps to send the nullfunc
till max tries reached.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There might be latency at AP side to update TIM IE which could cause the
station to send pspoll frame even after the wakeup. If the powersave is
disabled, the nullfunc notification alone is sufficient to receive
frames from the AP. And if the pspoll frame was already sent, no need to
resend the frame till it was acked by AP.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.

* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature

This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.

Cc: Paul Stewart <pstew@google.com>
Reported-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch improves ANI operations by switching among the immunity
levels based on PHY errors and beacon rssi which will adjust receiver
desensitizing parameters. The changes are

* Configure the Weak Signal Detection based on current immunity value.
* At highest OFDM immunity level poor performance was observed with
  strong interference. By tuning the FIR step and spur immunity levels
  and not changing any weak signal detection thresholds at any level
  helped to improve the performance.
* ANI took long time to recover back to lower immunity levels on heavy
  data load. As the listen time got reset to zero before reaching to
  the 5x of aniperiod, the immunity level is not lowering back even
  without any interference. This patch fix that.

Cc: Paul Stewart <pstew@google.com>
Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com>
Signed-off-by: Suresh Chandrasekaran <csuresh@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull networking fixes from David Miller:
 1) Name string overrun fix in gianfar driver from Joe Perches.

 2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El

 3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso.

 4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso.

 5) Add a parameter to skb_add_rx_frag() so we can fix the truesize
    adjustments in the drivers that use it.  The individual drivers
    aren't fixed by this commit, but will be dealt with using follow-on
    commits.  From Eric Dumazet.

 6) Add some device IDs to qmi_wwan driver, from Andrew Bird.

 7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node().  From
    Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: fix a potential rcu_read_lock() imbalance in rt6_fill_node()
  net: add a truesize parameter to skb_add_rx_frag()
  gianfar: Fix possible overrun and simplify interrupt name field creation
  USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces
  USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces
  USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces
  qlcnic: Bug fix for LRO
  netfilter: nf_conntrack: permanently attach timeout policy to conntrack
  netfilter: xt_CT: fix assignation of the generic protocol tracker
  netfilter: xt_CT: missing rcu_read_lock section in timeout assignment
  netfilter: cttimeout: fix dependency with l4protocol conntrack module
  netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6
  vhost: fix release path lockdep checks
  vhost: don't forget to schedule()
  tools/virtio: stub out strong barriers
  tools/virtio: add linux/hrtimer.h stub
  tools/virtio: add linux/module.h stub

Pull "ARM: device tree work" from Arnd Bergmann:
 "Most of these patches convert code from using static platform data to
  describing the hardware in the device tree.  This is only the first
  half of the changes for v3.4 because a lot of patches for this topic
  came in the last week before the merge window.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
  Document: devicetree: add OF documents for arch-mmp
  ARM: dts: append DTS file of pxa168
  ARM: mmp: append OF support on pxa168
  ARM: mmp: enable rtc clk in pxa168
  i2c: pxa: add OF support
  serial: pxa: add OF support
  arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
  ARM: OMAP2+: Remove extra ifdefs for board-generic
  ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
  ASoC: DT: Add digital microphone binding to PAZ00 board.
  ARM: dt: Add ARM PMU to tegra*.dtsi
  ARM: at91: at91sam9x5cm/dt: add leds support
  ARM: at91: usb_a9g20/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add leds support
  ARM: at91: usb_a9g20/dt: add leds support
  ARM: at91/pio: add new PIO3 features
  ARM: at91: add sam9_smc.o to at91sam9x5 build
  ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
  ARM: at91/tc: add device tree support to atmel_tclib
  ...

Pull "ARM: driver specific updates" from Arnd Bergmann:
 "These are all specific to some driver.  They are typically the
  platform side of a change in the drivers directory, such as adding a
  new driver or extending the interface to the platform.  In cases where
  there is no maintainer for the driver, or the maintainer prefers to
  have the platform changes in the same branch as the driver changes,
  the patches to the drivers are included as well.

  A much smaller set of driver updates that depend on other branches
  getting merged first will be sent later.

  The new export of tegra_chip_uid conflicts with other changes in
  fuse.c.  In rtc-sa1100.c, the global removal of IRQF_DISABLED
  conflicts with the cleanup of the interrupt handling of that driver.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up aforementioned trivial conflicts.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
  ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
  mmc: sdhci-s3c: add platform data for the second capability
  ARM: SAMSUNG: support the second capability for samsung-soc
  ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
  ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
  ARM: EXYNOS: Enable MDMA driver
  regulator: Remove bq24022 regulator driver
  rtc: sa1100: add OF support
  pxa: magician/hx4700: Convert to gpio-regulator from bq24022
  ARM: OMAP3+: SmartReflex: fix error handling
  ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
  ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
  ARM: OMAP3+: SmartReflex: misc cleanups
  ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
  ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
  ARM: OMAP3+: hwmod: add SmartReflex IRQs
  ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
  ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
  ARM: OMAP3+: SmartReflex: Add a shutdown hook
  ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
  ...

Conflicts:
	arch/arm/mach-tegra/Makefile
	arch/arm/mach-tegra/fuse.c
	drivers/rtc/rtc-sa1100.c

Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann:
 "This new subsystem provides a common way to talk to secondary
  processors on an SoC, e.g.  a DSP, GPU or service processor, using
  virtio as the transport.  In the long run, it should replace a few
  dozen vendor specific ways to do the same thing, which all never made
  it into the upstream kernel.  There is a broad agreement that rpmsg is
  the way to go here and several vendors have started working on
  replacing their own subsystems.

  Two branches each add one virtio protocol number.  Fortunately the
  numbers were agreed upon in advance, so there are only context
  changes.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial protocol number conflict due to the mentioned additions
next to each other.

* tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  remoteproc: cleanup resource table parsing paths
  remoteproc: remove the hardcoded vring alignment
  remoteproc/omap: remove the mbox_callback limitation
  remoteproc: remove the single rpmsg vdev limitation
  remoteproc: safer boot/shutdown order
  remoteproc: remoteproc_rpmsg -> remoteproc_virtio
  remoteproc: resource table overhaul
  rpmsg: fix build warning when dma_addr_t is 64-bit
  rpmsg: fix published buffer length in rpmsg_recv_done
  rpmsg: validate incoming message length before propagating
  rpmsg: fix name service endpoint leak
  remoteproc/omap: two Kconfig fixes
  remoteproc: make sure we're parsing a 32bit firmware
  remoteproc: s/big switch/lookup table/
  remoteproc: bail out if firmware has different endianess
  remoteproc: don't use virtio's weak barriers
  rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf
  rpmsg: depend on EXPERIMENTAL
  remoteproc: depend on EXPERIMENTAL
  rpmsg: add Kconfig menu
  ...

Conflicts:
	include/linux/virtio_ids.h

Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
 "These changes are all specific to one board only.  We're trying to
  keep the number of board files low, but generally board level updates
  are ok on platforms that are working on moving towards DT based
  probing, which will eventually lead to removing them.

  The board-ams-delta.c board file gets a conflict between the removal
  of ams_delta_config and the addition of a lot of other data.  The
  Kconfig file has two changes in the same line, and in exynos, the
  power domain cleanup conflicts with the addition of the image sensor
  device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
  [olof: Amended a fix for a mismerge to board-omap4panda.c]
  Signed-off-by: Olof Johansson <olof@lixom.net>"

Fixed up some fairly trivial conflicts manually.

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
  i.MX35-PDK: Add Camera support
  ARM : mx35: 3ds-board: add framebuffer device
  pxa/hx4700: Remove pcmcia platform_device structure
  ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
  ARM: pxa/hx4700: Remove unwanted request for GPIO105
  ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
  ARM: EXYNOS: Register JPEG on nuri
  ARM: EXYNOS: Register JPEG on universal_c210
  ARM: S5PV210: Enable JPEG on SMDKV210
  ARM: S5PV210: Add JPEG board definition
  ARM: EXYNOS: Enable JPEG on Origen
  ARM: EXYNOS: Enable JPEG on SMDKV310
  ARM: EXYNOS: Add __init attribute to universal_camera_init()
  ARM: EXYNOS: Add __init attribute to nuri_camera_init()
  ARM: S5PV210: Enable FIMC on SMDKC110
  ARM: S5PV210: Enable FIMC on SMDKV210
  ARM: S5PV210: Enable MFC on SMDKC110
  ARM: S5PV210: Enable MFC on SMDKV210
  ARM: EXYNOS: Enable G2D on SMDKV310
  ARM: tegra: update defconfig
  ...

Pull "ARM: SoC specific updates" from Arnd Bergmann:
 "These changes are all specific to an soc family or the code for one
  soc.  Lots of work for Tegra3 this time, but also a lot of other
  platforms.  There will be another (smaller) set of soc patches later
  in the merge window for stuff that has dependencies on external trees
  or that was sent just before the merge window opened.

  The asoc tree added a few devices to the i.mx platform, which conflict
  with other devices added in the same place here.

  The tegra Makefile conflicts between a number of branches, mostly
  because of changes regarding localtimer.c, which was removed in the
  end.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up some trivial conflicts, including the mentioned Tegra Makefile.

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
  ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
  ARM: EXYNOS: add support JPEG
  ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
  ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
  ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
  ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
  ARM: S5PV210: Add usb otg phy control
  ARM: S3C64XX: Add usb otg phy control
  ARM: EXYNOS: Enable l2 configuration through device tree
  ARM: EXYNOS: remove useless code to save/restore L2
  ARM: EXYNOS: save L2 settings during bootup
  ARM: S5P: add L2 early resume code
  ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
  ARM: mx35: Setup the AIPS registers
  ARM: mx5: Use common function for configuring AIPS
  ARM: mx3: Setup AIPS registers
  ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
  ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
  ARM: imx: update imx_v6_v7_defconfig
  ARM: tegra: Demote EMC clock inconsistency BUG to WARN
  ...

Pull "ARM: timer cleanup work" from Arnd Bergmann:
 "These are split out from the generic soc and driver updates because
  there was a lot of conflicting work by multiple people.  Marc Zyngier
  worked on simplifying the "localtimer" interfaces, and some of the
  platforms are touching the same code as they move to device tree based
  booting.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  ARM: tegra: select USB_ULPI if USB is selected
  arm/tegra: pcie: fix return value of function
  ARM: ux500: fix compilation after local timer rework
  ARM: shmobile: remove additional __io() macro use
  ARM: local timers: make the runtime registration interface mandatory
  ARM: local timers: convert MSM to runtime registration interface
  ARM: local timers: convert exynos to runtime registration interface
  ARM: smp_twd: remove old local timer interface
  ARM: imx6q: convert to twd_local_timer_register() interface
  ARM: highbank: convert to twd_local_timer_register() interface
  ARM: ux500: convert to twd_local_timer_register() interface
  ARM: shmobile: convert to twd_local_timer_register() interface
  ARM: tegra: convert to twd_local_timer_register() interface
  ARM: plat-versatile: convert to twd_local_timer_register() interface
  ARM: OMAP4: convert to twd_local_timer_register() interface
  ARM: smp_twd: add device tree support
  ARM: smp_twd: add runtime registration support
  ARM: local timers: introduce a new registration interface
  ARM: smp_twd: make local_timer_stop a symbol instead of a #define
  ARM: mach-shmobile: default to no earlytimer
  ...

Pull "ARM: global cleanups" from Arnd Bergmann:
 "Quite a bit of code gets removed, and some stuff moved around, mostly
  the old samsung s3c24xx stuff.  There should be no functional changes
  in this series otherwise.  Some cleanups have dependencies on other
  arm-soc branches and will be sent in the second round.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial conflicts mainly due to #include's being changes on
both sides.

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
  ep93xx: Remove unnecessary includes of ep93xx-regs.h
  ep93xx: Move EP93XX_SYSCON defines to SoC private header
  ep93xx: Move crunch code to mach-ep93xx directory
  ep93xx: Make syscon access functions private to SoC
  ep93xx: Configure GPIO ports in core code
  ep93xx: Move peripheral defines to local SoC header
  ep93xx: Convert the watchdog driver into a platform device.
  ep93xx: Use ioremap for backlight driver
  ep93xx: Move GPIO defines to gpio-ep93xx.h
  ep93xx: Don't use system controller defines in audio drivers
  ep93xx: Move PHYS_BASE defines to local SoC header file
  ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
  ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
  PM / devfreq: update the name of EXYNOS clock registers that were omitted
  PM / devfreq: update the name of EXYNOS clock register
  ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
  ARM: EXYNOS: use static declaration on regarding clock
  ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
  ARM: OMAP2+: Fix build error after merge
  ARM: S3C24XX: remove call to s3c24xx_setup_clocks
  ...

Pull "ARM: subarch maintainer updates" from Arnd Bergmann:
 "This is a collection of updates to the MAINTAINERS file, separated out
  mostly to give an overview of what has changed regarding who does
  what.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: tegra: update main repo and add patchwork
  MAINTAINERS: update MAINTAINERS email entry
  MAINTAINERS: update maintainer entry for pxa/hx4700
  MAINTAINERS: ARM: tegra: update Stephen's email address
  MAINTAINERS: add TI DaVinci git tree information
  MAINTAINERS: mark TI DaVinci list as "moderated"
  MAINTAINERS: remove arch/arm/mach-mx*/ from IMX entry

Pull "ARM: Non-critical bug fixes" from Ardn Bergmann:
 "Simple bug fixes that were not considered important enough for
  inclusion into 3.3.  One bug fix was originally intended for 3.3 but
  accidentally got missed, but is not marked stable because it should
  only get backported once later fixes also make it into v3.4.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
  iomux-mx25.h slew rate adjusted for LCD __LD pins
  ARM: davinci: DA850: move da850_register_pm to .init.text
  ARM: davinci: cpufreq: fix compiler warning
  ARM: OMAP2+: Fix build for omap4 only builds with missing include of linux/bug.h
  ARM: OMAP2+: Fix section warnings for hsmmc_init_one
  ARM: OMAP2+: Fix build issues with missing include of linux/bug.h
  ARM: OMAP2+: gpmc-smsc911x: only register regulator for first instance
  ARM: OMAP3+: PM: VP: fix integer truncation error
  ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled
  ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices()
  ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set
  ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected
  ARM: OMAP1: Fix section mismatch for omap1_init_early()
  ARM: OMAP1: Fix typo in lcd_dma.c
  ARM: OMAP: mailbox: trivial whitespace fix
  ARM: OMAP: Remove definition cpu_is_omap4430()
  ARM: OMAP2+: included some headers twice
  ARM: OMAP: clock.c: included linux/debugfs.h twice
  ARM: OMAP: don't build hwspinlock in vain
  ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided
  ...

Commit f2c31e32 (net: fix NULL dereferences in check_peer_redir() )
added a regression in rt6_fill_node(), leading to rcu_read_lock()
imbalance.

Thats because NLA_PUT() can make a jump to nla_put_failure label.

Fix this by using nla_put()

Many thanks to Ben Greear for his help
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into next/boards

The asoc branch that was already merged into v3.4 contains some
board-level changes that conflict with patches we already have
here, so pull in that branch to resolve the conflicts.

Conflicts:
	arch/arm/mach-imx/mach-imx27_visstrim_m10.c
	arch/arm/mach-omap2/board-omap4panda.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended fix for mismerge as reported by Kevin Hilman]
Signed-off-by: Olof Johansson <olof@lixom.net>

In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver
rtl8192ce are reported. One fix (commit a9b89e25) has already been applied,
and it helped, but the maximum RX speed would still drop to 1 Mbps. As in
the previous fix, the initial gain was determined to be the problem; however,
the problem arises from a setting of the gain when scans are started.

Driver rtl8192de also has the same code structure - this one is fixed as well.
Reported-and-Tested-by: Ivan Pesin <ivan.pesin@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I simply don't have any hobby hacking time after family time
and non-kernel-related job time, so I resume status as part-time
mailing list lurker.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Is possible that we will arm the tid_rx->reorder_timer after
del_timer_sync() in ___ieee80211_stop_rx_ba_session(). We need to stop
timer after RCU grace period finish, so move it to
ieee80211_free_tid_rx(). Timer will not be armed again, as
rcu_dereference(sta->ampdu_mlme.tid_rx[tid]) will return NULL.

Debug object detected problem with the following warning:
ODEBUG: free active (active state 0) object type: timer_list hint: sta_rx_agg_reorder_timer_expired+0x0/0xf0 [mac80211]

Bug report (with all warning messages):
https://bugzilla.redhat.com/show_bug.cgi?id=804007Reported-by: "jan p. springer" <jsd@igroup.org>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Another good catch from Jakub Kicinski. This patch fixes my
recent commit: ed61e2b0
"rt2x00: rt2800usb: rework txdone code"

We should reread status register only when nobody else start already
reading status i.e. test_and_set_bit(TX_STATUS_READING, flags) return 0.
Reported-by: Jakub Kicinski <moorray@wp.pl>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>