- 15 Dec, 2023 13 commits
-
-
Ping-Ke Shih authored
To support MLO of WiFi 7, we should configure hardware as DBCC mode, and notify this status to firmware. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20231211083341.118047-6-pkshih@realtek.com
-
Ping-Ke Shih authored
Many existing MAC access functions are used by WiFi 6 chips only, so add suffix _ax to be clearer. Some are common and can be used by WiFi 7, so export this kind of functions. This patch doesn't change logic at all. Signed-off-by:
-
Ping-Ke Shih authored
Before accessing CMAC and DMAC registers, we should ensure they have been powered on, so add flag to determine the state. For old chips, we read registers and check corresponding bit, but it takes extra cost to read. Signed-off-by:
-
Ping-Ke Shih authored
The power on/off functions are to turn on hardware function blocks and to turn off them if we are going to stay in idle state. Signed-off-by:
-
Ping-Ke Shih authored
The XTAL SI is a serial interface to indirectly access registers of analog hardware circuit. Since WiFi 7 chips use different registers, add a ops to access them via common functions. This patch doesn't change logic for existing chips. Signed-off-by:
-
Ping-Ke Shih authored
With formatted string loaded from firmware file, we can use the formatted string ID and get corresponding string, and then use regular rtw89_debug() to show the message if debug mask of RFK is enabled. If the string ID doesn't present, fallback to print plain hexadecimal. Signed-off-by:
-
Ping-Ke Shih authored
RFK log events contains two types. One called RUN log is to reflect state during RFK is running, and it replies on formatted string loaded from firmware file, but print this type as plain hexadecimal only in this patch. The other is REPORT log that reflects the final result of a RFK, and each calibration has its own struct to carry many specific information. Signed-off-by:
-
Ping-Ke Shih authored
Trigger a RFK (RF calibration) in firmware by a H2C command, and in progress it reports log and a result finally by C2H events. Firstly, add prototype of the C2H event handlers to have a simple picture of framework. The callers who trigger H2C will wait until a C2H event is received, so we must process these C2H events in receiving process. Thus, mark this kind of C2H events as atomic. Also, timestamp is also useful for debugging, mark C2H events carrying RFK log as atomic as well. Signed-off-by:
-
Ping-Ke Shih authored
To debug RFK (RF calibration) in firmware, it sends log via firmware C2H events to driver with string format ID and four arguments. Load formatted string from firmware file, and the string ID can get back its string. Then, use regular print format to show the message. This firmware element layout looks like +============================================+ | elm ID | elm size | version | | +----------+----------+----------+-----------+ | | nr |rsvd |rfk_id|rsvd| +--------------------------------------------+ | offset[] (__le16 * nr) | | ... | +--------------------------------------------+ | formatted string with null termintor (*nr) | | ... | +============================================+ * a firmware file can contains more than one elements with this element ID named RTW89_FW_ELEMENT_ID_RFKLOG_FMT (19), because many RFK needs its own formatted strings, so add 'rfk_id' to know it belongs to which RFK. * the 'formatted string' just follow 'offset[]' without padding to align 32bits. Signed-off-by: -
Ping-Ke Shih authored
8922AE has more than one hardware version, and they use different BB MCU firmware, so occupy a byte from element priv[] to annotate version. Since there are more than one firmware and only matched version is adopted, return 1 to ignore not matched firmware. +===========================================+ | elm ID | elm size | version | | +----------+----------+----------+----------+ | | element_priv[] | +-------------------------------------------+ change to | v +===========================================+ | elm ID | elm size | version | | +----------+----------+----------+----------+ | | cv | element_rsvd[] | +-------------------------------------------+ Signed-off-by: -
Ping-Ke Shih authored
The TX power track tables are used to define compensation power reflected to thermal value. Currently, we have 16 (2 * 4 * 2) tables made by combinations of {negative/positive thermal value, 2GHz/2GHz-CCK/5GHz/6GHz, path A/B} Signed-off-by: -
David Lin authored
AP BSSID configuration is missing at AP start. Without this fix, FW returns STA interface MAC address after first init. When hostapd restarts, it gets MAC address from netdev before driver sets STA MAC to netdev again. Now MAC address between hostapd and net interface are different causes STA cannot connect to AP. After that MAC address of uap0 mlan0 become the same. And issue disappears after following hostapd restart (another issue is AP/STA MAC address become the same). This patch fixes the issue cleanly. Signed-off-by:
David Lin <yu-hao.lin@nxp.com> Fixes: 12190c5d ("mwifiex: add cfg80211 start_ap and stop_ap handlers") Cc: stable@vger.kernel.org Reviewed-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD Acked-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
David Lin authored
For SDIO IW416, due to a bug, FW may return ready before complete full initialization. Command timeout may occur at driver load after reboot. Workaround by adding 100ms delay at checking FW status. Signed-off-by:
-
- 14 Dec, 2023 5 commits
-
-
Randy Dunlap authored
Correct run-on sentences by changing "," to ";". Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Kalle Valo <kvalo@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Link: https://msgid.link/20231213054809.23475-1-rdunlap@infradead.orgSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Randy Dunlap authored
Correct a run-on sentence by changing "," to ";". Add a subject in one sentence. Signed-off-by:
-
Randy Dunlap authored
Correct spelling as reported by codespell. Correct run-on sentences and other grammar issues. Add hyphenation of adjectives. Correct some punctuation. Signed-off-by:
-
Randy Dunlap authored
Correct spelling and run-on sentences. Signed-off-by:
-
Johannes Berg authored
The build can become unreproducible if the list of files found by $(wildcard ...) differs. Sort the list to avoid this. Signed-off-by:
-
- 12 Dec, 2023 22 commits
-
-
Kunwu Chan authored
kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Cc: Kunwu Chan <kunwu.chan@hotmail.com> Signed-off-by:
Kunwu Chan <chentao@kylinos.cn> Acked-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
Chris Morgan authored
When the MAC address read from the efuse data is invalid, warn the user and use a random MAC address instead. On a device I am currently using (Anbernic RG-ARC) with a rtw8821cs the efuse appears to be incompletely/improperly programmed. The MAC address reads as ff:ff:ff:ff:ff:ff. When networkmanager attempts to initiate a connection (and I haven't hard-coded a MAC address or set it to random) it fails to establish a connection. Signed-off-by:
Chris Morgan <macromorgan@hotmail.com> Acked-by:
-
Dmitry Antipov authored
Since 'ieee80211_beacon_get()' can return NULL, 'wfx_set_mfp_ap()' should check the return value before examining skb data. So convert the latter to return an appropriate error code and propagate it to return from 'wfx_start_ap()' as well. Compile tested only. Signed-off-by:
Dmitry Antipov <dmantipov@yandex.ru> Tested-by:
Jérôme Pouiller <jerome.pouiller@silabs.com> Acked-by:
-
Arnd Bergmann authored
After -Wstringop-overflow got enabled, the rtw89 driver produced two odd warnings with gcc-13: drivers/net/wireless/realtek/rtw89/coex.c: In function 'rtw89_btc_ntfy_scan_start': drivers/net/wireless/realtek/rtw89/coex.c:5362:50: error: writing 1 byte into a region of size 0 [-Werror=stringop-overflow=] 5362 | wl->dbcc_info.scan_band[phy_idx] = band; | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~ In file included from drivers/net/wireless/realtek/rtw89/coex.h:8, from drivers/net/wireless/realtek/rtw89/coex.c:5: drivers/net/wireless/realtek/rtw89/core.h:1441:12: note: at offset [64, 255] into destination object 'scan_band' of size 2 1441 | u8 scan_band[RTW89_PHY_MAX]; /* scan band in each phy */ | ^~~~~~~~~ drivers/net/wireless/realtek/rtw89/coex.c: In function 'rtw89_btc_ntfy_switch_band': drivers/net/wireless/realtek/rtw89/coex.c:5406:50: error: writing 1 byte into a region of size 0 [-Werror=stringop-overflow=] 5406 | wl->dbcc_info.scan_band[phy_idx] = band; | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~ drivers/net/wireless/realtek/rtw89/core.h:1441:12: note: at offset [64, 255] into destination object 'scan_band' of size 2 1441 | u8 scan_band[RTW89_PHY_MAX]; /* scan band in each phy */ | ^~~~~~~~~ I don't know what happened here, but adding an explicit range check shuts up the output. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 6.8 * fixes * nvmem eeprom improvements * mt7996 eht improvements * mt7996 wed support * mt7996 36-bit DMA support
-
Dmitry Antipov authored
The WARN_ON() in subject was actually seen only once, with 5.10.200 under syzkaller. It looks like a weird artifact of (ab?)using the syzkaller itself [1], and hopefully may be safely removed. [1] https://lore.kernel.org/linux-wireless/1bd8f266-dee0-4d4e-9b50-e22546b55763@yandex.ru/T/#uSigned-off-by:
-
Johannes Berg authored
The ESS capability bit is reserved in frames transmitted by the client, so we shouldn't set it. Since we've set it for decades, keep that old behaviour unless we're connection to a new EHT AP. Signed-off-by:
Gregory Greenman <gregory.greenman@intel.com> Signed-off-by:
Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20231211085121.65005aba900b.I3d00c8741400572a89a7508b5ae612c968874ad7@changeidSigned-off-by:
-
Benjamin Berg authored
When doing a channel switch, cfg80211_update_known_bss may be called with a BSS where both proberesp_ies and beacon_ies is set. If that happens, both need to be consumed. Signed-off-by:
Benjamin Berg <benjamin.berg@intel.com> Signed-off-by:
-
Benjamin Berg authored
The specification says that this information should not be explicitly included in the per-STA profile. However, we need this information readily available in the BSS for userspace and also internally when associating. As such, append the appropriate element before adding/updating the BSS. Signed-off-by:
-
Andrei Otcheretianski authored
ENOTSUPP isn't a standard error code, don't use it. Signed-off-by:
Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by:
-
Andrei Otcheretianski authored
ENOTSUP isn't a standard error code. EOPNOTSUPP should be used instead. Signed-off-by:
-
Johannes Berg authored
There may be cases where puncturing isn't possible, and a connection needs to be downgraded. Add a hardware flag to support this. This is likely temporary: it seems we will need to move puncturing to the chandef/channel context. Signed-off-by:
-
Ilan Peer authored
Add support for setting the TID to link mapping for a non-AP MLD station. This is useful in cases user space needs to restrict the possible set of active links, e.g., since it got a BSS Transition Management request forcing to use only a subset of the valid links etc. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Reviewed-by:
-
Johannes Berg authored
With the locking rework, more functions need to be called with the wiphy mutex held. Document that, and for that use the "Context" description that shows up more nicely in the generated documentation. Signed-off-by:
-
Johannes Berg authored
Sometimes there may be reasons for which a BSS that's actually found in scan cannot be used to connect to, for example a nonprimary link of an NSTR mobile AP MLD cannot be used for normal direct connections to it. Not indicating these to userspace as we do now of course avoids being able to connect to them, but it's better if they're shown to userspace and it can make an appropriate decision, without e.g. doing an additional ML probe. Thus add an indication of what a BSS can be used for, currently "normal" and "MLD link", including a reason bitmap for it being not usable. The latter can be extended later for certain BSSes if there are other reasons they cannot be used. Signed-off-by:
-
Emmanuel Grumbach authored
Newest firmware has completely offloaded this logic and this command will be deprecated soon. Based on a capability bit advertised by the firmware, skip this command. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Johannes Berg authored
There's only one user of this code, which is STA unblock during sleep for uAPSD on really old devices. Instead of having this all through the API with calls up and down, just implemented a special-case CMD_BLOCK_TXQS flag for this, it's only needed in the old gen1 transport. While at it, fix a complain that lockdep would have, as we lock the cmd queue and then the TXQs in the reclaim by using spin_lock_nested(). We no longer need to disable BHs in iwl_trans_pcie_block_txq_ptrs() since it's called with them disabled already. Signed-off-by:
-
Johannes Berg authored
This causes fortify warnings when compiled against recent kernels with recent compilers, and generally is not supported in the kernel anymore. Signed-off-by:
-
Johannes Berg authored
This never returns an error and the return value is never checked anyway, so it can just be void. Signed-off-by:
-
Johannes Berg authored
Signed-off-by:
-
Johannes Berg authored
We shouldn't access the device if we don't hold a reference, and if - after locking - we see that it has no bus, we also can't do anything, in fact, pci_stop_and_remove_bus_device() will be a no-op. Signed-off-by:
-
Emmanuel Grumbach authored
This can be used by the user space when it wants to clear the data we collected so far for privacy reasons. Signed-off-by:
-
