Add description for NXP imx8 families like imx8mp/imx8dxl
that integrate the Synopsys gmac IP version 5.10a.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP.
This patch adds settings for NXP imx8 glue layer:
- clocks
- dwmac address width
- phy interface mode selection
- adjust rgmii txclk rate

v2:
- adjust code sequences in order to have reverse christmas
  tree local variable ordering.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add "snps,dwmac-5.10a" compatible string for 5.10a version that can
avoid to define some plat data in glue layer.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

net/tipc/msg.c: In function 'tipc_msg_append':
net/tipc/msg.c:215:24: warning:
 variable 'prev' set but not used [-Wunused-but-set-variable]

commit 0a3e060f ("tipc: add test for Nagle algorithm effectiveness")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup,
both under the same VLAN-filtering bridge, both in the
SJA1105_VLAN_BEST_EFFORT state.

If we try to change the VLAN state of one of the switches (to
SJA1105_VLAN_FILTERING_FULL) we get the following error:

devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value
false cmode runtime
[   38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory.
               L2 memory partitions and VL memory partitions share the
               same space. The sum of all 16 memory partitions is not
               allowed to be larger than 929 128-byte blocks (or 910
               with retagging). Please adjust
               l2-forwarding-parameters-table.part_spc and/or
               vl-forwarding-parameters-table.partspc.
[   38.356803] sja1105 spi2.1: Invalid config, cannot upload

This is because the spi/spi2.1 switch doesn't support tagging anymore in
the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any
retagging rules defined. Great, so it can use more frame memory
(retagging consumes extra memory).

But the built-in low-level static config checker from the sja1105 driver
says "not so fast, you've increased the frame memory to non-retagging
values, but you still kept the retagging rules in the static config".

So we need to rebuild the VLAN table immediately before re-uploading the
static config, operation which will take care, based on the new VLAN
state, of removing the retagging rules.

Fixes: 3f01c91a ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Right now, our only tag_8021q user, sja1105, has the ability to restore
bridge VLANs on its own, so this logic is unnecessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christoph Hellwig says:

====================
remove kernel_setsockopt v4

now that only the dlm calls to sctp are left for kernel_setsockopt,
while we haven't really made much progress with the sctp setsockopt
refactoring, how about this small series that splits out a
sctp_setsockopt_bindx_kernel that takes a kernel space address array
to share more code as requested by Marcelo.  This should fit in with
whatever variant of the refator of sctp setsockopt we go with, but
just solved the immediate problem for now.

Changes since v3:
 - dropped all the merged patches, just sctp setsockopt left now
 - factor out a new sctp_setsockopt_bindx_kernel helper instead of
   duplicating a small amount of logic

Changes since v2:
 - drop the separately merged kernel_getopt_removal
 - drop the sctp patches, as there is conflicting cleanup going on
 - add an additional ACK for the rxrpc changes

Changes since v1:
 - use ->getname for sctp sockets in dlm
 - add a new ->bind_add struct proto method for dlm/sctp
 - switch the ipv6 and remaining sctp helpers to inline function so that
   the ipv6 and sctp modules are not pulled in by any module that could
   potentially use ipv6 or sctp connections
 - remove arguments to various sock_* helpers that are always used with
   the same constant arguments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No users left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SCTP protocol allows to bind multiple address to a socket.  That
feature is currently only exposed as a socket option.  Add a bind_add
method struct proto that allows to bind additional addresses, and
switch the dlm code to use the method instead of going through the
socket option from kernel space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split out a sctp_setsockopt_bindx_kernel that takes a kernel pointer
to the sockaddr and make sctp_setsockopt_bindx a small wrapper around
it.  This prepares for adding a new bind_add proto op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper to directly set the SCTP_NODELAY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2020-05-29

1) Add IPv6 encapsulation support for ESP over UDP and TCP.
   From Sabrina Dubroca.

2) Remove unneeded reference when initializing xfrm interfaces.
   From Nicolas Dichtel.

3) Remove some indirect calls from the state_afinfo.
   From Florian Westphal.

Please note that this pull request has two merge conflicts

between commit:

  0c922a48 ("xfrm: Always set XFRM_TRANSFORMED in xfrm{4,6}_output_finish")

  from Linus' tree and commit:

    2ab6096d ("xfrm: remove output_finish indirection from xfrm_state_afinfo")

    from the ipsec-next tree.

and between commit:

  3986912f ("ipv6: move SIOCADDRT and SIOCDELRT handling into ->compat_ioctl")

  from the net-next tree and commit:

    0146dca7 ("xfrm: add support for UDPv6 encapsulation of ESP")

    from the ipsec-next tree.

Both conflicts can be resolved as done in linux-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to call phy_restore_page() even if phy_select_page() fails.
Otherwise we are holding the phy_lock_mdio_bus() lock.  This requirement
is documented at the start of the phy_select_page() function.

Fixes: a618e86d ("net : phy: marvell: Speedup TDR data retrieval by only changing page once")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYs using the vsc8574_probe fail to be initialized and their
config_init return -EIO leading to errors like:
"could not attach PHY: -5".

This is because when the conversion of the MSCC PHY driver to use the
shared PHY package helpers was done, the base address retrieval and the
base PHY read and write helpers in the driver were modified. In
particular, the base address retrieval logic was moved from the
config_init to the probe. But the vsc8574_probe was forgotten. This
patch fixes it.

Fixes: deb04e9c ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The desc pointer is set but not used. Remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8c7bd5a4 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2020-05-28

This series contains updates to e1000, e1000e, igc, igb, ixgbe and i40e.

Takashi Iwai, from SUSE, replaces some uses of snprintf() with
scnprintf() since the succeeding calls may go beyond the given buffer
limit in i40e.

Jesper Dangaard Brouer fixes up code comments in i40e_xsk.c

Xie XiuQi, from Huawei, fixes a signed-integer-overflow warning ixgbe
driver.

Jason Yan, from Huawei, converts '==' expression to bool to resolve
warnings, also fixed a warning for assigning 0/1 to a bool variable in
the ixgbe driver.  Converts functions that always return 0 to void in the
igb and i40e drivers.

YueHaibing, from Hauwei, cleans up dead code in ixgbe driver.

Sasha cleans up more dead code which is not used in the igc driver.
Added receive error counter to reflect the total number of non-filtered
packets received with errors.  Fixed a register define name to properly
reflect the register address being used.

Andre updates the igc driver to reject NFC rules that have multiple
matches, which is not supported in i225 devices.  Updates the total
number of NFC rules supported and added a code comment to explain what
is supported.

Punit Agrawal, from Toshiba, relaxes the condition to trigger a reset
for ME, which was leading to inconsistency between the state of the
hardware as expected by the driver in e1000e.

Hari, from the Linux community, cleaned up a code comment in the e1000
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

'Commit dacce2be ("vmxnet3: add geneve and vxlan tunnel offload
support")' added support for encapsulation offload. However, while
preparing inner tso packet, it uses reference to outer ip headers.

This patch fixes this issue by using correct reference for inner
headers.

Fixes: dacce2be ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Continuous Double "the" in a comment. Changed it to single "the"
Signed-off-by: Hari <harichandrakanthan@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the following coccicheck warning:

drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.

Fix this by dropping the check for number of delay iterations.

While at it, also make __ew32_prepare() static as it's not used
anywhere else.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.

Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.

$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2

When such rule is applied, we have 2 unwanted behaviors:

    1) Any frame matching MACADDR will be assigned to queue 2. It
       doesn't matter the ETYPE value.

    2) Any accepted frame that has Ethertype equals to ETYPE, no matter
       the mac address, will be assigned to queue 2 as well.

In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Transmit underrun, late and excess collision flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:

drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

commit b5f69ccf ("ixgbe: avoid bringing rings up/down as macvlans are added/removed")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the following coccicheck warning:

drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c:105:2-38: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

No need to convert '==' expression to bool. This fixes the following
coccicheck warning:

drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:68:11-16: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ubsan report this warning, fix it by adding a unsigned suffix.

UBSAN: signed-integer-overflow in
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:2246:26
65535 * 65537 cannot be represented in type 'int'
CPU: 21 PID: 7 Comm: kworker/u256:0 Not tainted 5.7.0-rc3-debug+ #39
Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 03/27/2020
Workqueue: ixgbe ixgbe_service_task [ixgbe]
Call trace:
 dump_backtrace+0x0/0x3f0
 show_stack+0x28/0x38
 dump_stack+0x154/0x1e4
 ubsan_epilogue+0x18/0x60
 handle_overflow+0xf8/0x148
 __ubsan_handle_mul_overflow+0x34/0x48
 ixgbe_fc_enable_generic+0x4d0/0x590 [ixgbe]
 ixgbe_service_task+0xc20/0x1f78 [ixgbe]
 process_one_work+0x8f0/0xf18
 worker_thread+0x430/0x6d0
 kthread+0x218/0x238
 ret_from_fork+0x10/0x18
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The comment above i40e_run_xdp_zc() was clearly copy-pasted from
function i40e_xsk_umem_setup, which is just above.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit.  Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Huazhong Tan says:

====================
net: hns3: misc updates for -next

This patchset includes some updates for the HNS3 ethernet driver.

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling hclge_parse_speed() fails, printing out the speed is
helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove some fields in struct hclge_dev which have not been used.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HCLGEVF_CMDQ_INTR_SRC_REG and HCLGEVF_CMDQ_INTR_STS_REG are same
as HCLGEVF_VECTOR0_CMDQ_SRC_REG and HCLGEVF_VECTOR0_CMDQ_STAT_REG,
replace the former with the latter, and rename macro
HCLGEVF_VECTOR0_CMDQ_STAT_REG since 'stat' is not abbreviation of
'state'.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since field .uinfo in struct hnae3_handle never be used,
so remove it and its structure definition.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove HNAE3_RESTORE_CLIENT which is not needed now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>