This syntax error was covered by L2TP_REFCNT_DEBUG not being set by
default.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2014-09-03

The following series of patches includes fixes/updates to the driver.

- Query the device for the actual speed mode (KR/KX) rather than trying
  to track it
- Update parallel detection logic to support KR mode
- Fix new warnings from checkpatch in the amd-xgbe and amd-xgbe-phy
  driver

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is.  Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: random MAC address

If the interface has invalid MAC address, it couldn't
be used. In order to let it work normally, give a
random one.

v3:
  Remove
	ether_addr_copy(dev->perm_addr, dev->dev_addr);

v2:
  Use "%pM" format specifier for printing a MAC address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Govindarajulu Varadarajan says:

====================
enic: Add support for rx_copybreak

The following series implements rx_copybreak.

dma_map_single()/dma_unmap_single() is more expensive than alloc_skb & memcpy
for smaller packets. By doing this we can reuse the dma buff which is already
mapped. This is very useful when iommu is on. The default skb copybreak value
is 256.

When iommu is on, we can go much higher than 256. All the drivers that supports
rx_copybreak provides module parameter to change this value. Since module
parameter is the least preferred way for changing driver values, this series
adds ethtool support for setting rx_copybreak.

v4:
Validate tunable length in ethtool_get_tunable, not in driver implemented
function.

Loose tunable_ops array for each tunable type. Define one function and let the
driver use switch case for each type.

Use double underscore for data type in UAPI headers.
Use const qualifier where possible.

v3:
Add tunable namespace to ethtool. Use new ethtool cmd ETHTOOL_S/GTUNABLE to
set/get rx_copybreak from userspace.

v2:
Add new ethtool_cmd for DMA buffer parameters, instead of adding new members to
existing ethtool_ringparam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.

Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds new ethtool cmd, ETHTOOL_GTUNABLE & ETHTOOL_STUNABLE for getting
tunable values from driver.

Add get_tunable and set_tunable to ethtool_ops. Driver implements these
functions for getting/setting tunable value.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcel reported to see the following message when autoloading
is being triggered when adding nlmon device:

  Loading kernel module for a network device with
  CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias
  netdev-nlmon instead.

This false-positive happens despite with having correct
capabilities set, e.g. through issuing `ip link del dev nlmon`
more than once on a valid device with name nlmon, but Marcel
has also seen it on creation time when no nlmon module is
previously compiled-in or loaded as module and the device
name equals a link type name (e.g. nlmon, vxlan, team).

Stephen says:

  The netdev module alias is a hold over from the past. For
  normal devices, people used to create a alias eth0 to and
  point it to the type of network device used, that was back
  in the bad old ISA days before real discovery.

  Also, the tunnels create module alias for the control device
  and ip used to use this to autoload the tunnel device.

  The message is bogus and should just be removed, I also see
  it in a couple of other cases where tap devices are renamed
  for other usese.

As mentioned in 8909c9ad ("net: don't allow CAP_NET_ADMIN
to load non-netdev kernel modules"), we nevertheless still
might want to leave the old autoloading behaviour in place
as it could break old scripts, so for now, lets just remove
the log message as Stephen suggests.

Reference: http://thread.gmane.org/gmane.linux.kernel/1105168Reported-by: Marcel Holtmann <marcel@holtmann.org>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate.  This patch moves the to be interpreted bytecode to
read-only pages.

In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9b ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").

This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).

Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.

Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables.  Brad Spengler proposed the same idea
via Twitter during development of this patch.

Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():

Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:

- updating the Ethernet MAC registers only make sense when a physical
  link is present
- the PHY library state machine first set phydev->link = 0 before
  invoking phydev->adjust_link in the PHY_HALTED case

This is a similar fix to the GENET one:
c677ba8b ("net: bcmgenet: update
UMAC_CMD only when link is detected").

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As in IPv6 people might increase the igmp query robustness variable to
make sure unsolicited state change reports aren't lost on the network. Add
and document this new knob to igmp code.

RFCs allow tuning this parameter back to first IGMP RFC, so we also use
this setting for all counters, including source specific multicast.

Also take over sysctl value when upping the interface and don't reuse
the last one seen on the interface.

Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new sysctl_mld_qrv knob to configure the mldv1/v2 query
robustness variable. It specifies how many retransmit of unsolicited mld
retransmit should happen. Admins might want to tune this on lossy links.

Also reset mld state on interface down/up, so we pick up new sysctl
settings during interface up event.

IPv6 certification requests this knob to be available.

I didn't make this knob netns specific, as it is mostly a setting in a
physical environment and should be per host.

Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate.  This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although rhashtable library allows user to specify a quiet big size
for user's created hash table, the table may be shrunk to a
very small size - HASH_MIN_SIZE(4) after object is removed from
the table at the first time. Subsequently, even if the total amount
of objects saved in the table is quite lower than user's initial
setting in a long time, the hash table size is still dynamically
adjusted by rhashtable_shrink() or rhashtable_expand() each time
object is inserted or removed from the table. However, as
synchronize_rcu() has to be called when table is shrunk or
expanded by the two functions, we should permit user to set the
minimum table size through configuring the minimum number of shifts
according to user specific requirement, avoiding these expensive
actions of shrinking or expanding because of calling synchronize_rcu().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 50cbe9ab ("net: Validate xmit SKBs right when we
pull them out of the qdisc") the validation code was moved out of
dev_hard_start_xmit and into dequeue_skb.

However this overlooked the fact that we do not always enqueue
the skb onto a qdisc. First situation is if qdisc have flag
TCQ_F_CAN_BYPASS and qdisc is empty.  Second situation is if
there is no qdisc on the device, which is a common case for
software devices.

Originally spotted and inital patch by Alexander Duyck.
As a result Alex was seeing issues trying to connect to a
vhost_net interface after commit 50cbe9ab was applied.

Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the
code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in
__dev_queue_xmit() when no qdisc.

Also handle the error situation where dev_hard_start_xmit() could
return a skb list, and does not return dev_xmit_complete(rc) and
falls through to the kfree_skb(), in that situation it should
call kfree_skb_list().

Fixes:  50cbe9ab ("net: Validate xmit SKBs right when we pull them out of the qdisc")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

More minor fixes to merge commit 53fda7f7 (Merge branch 'xmit_list')
that allows us to work with a list of SKBs.

Fixing exit cases in qdisc_reset() and qdisc_destroy(), where a
leftover requeued SKB (qdisc->gso_skb) can have the potential of
being a skb list, thus use kfree_skb_list().

This is a followup to commit 10770bc2 ("qdisc: adjustments for
API allowing skb list xmits").
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Minor adjustments for merge commit 53fda7f7 (Merge branch 'xmit_list')
that allows us to work with a list of SKBs.

Update code doc to function sch_direct_xmit().

In handle_dev_cpu_collision() use kfree_skb_list() in error handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused 'dev' variable from arc_emac_remove(), since it's
not being used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unnecessary double parenthesis around if statement.
Signed-off-by: David Wood <devel@dtwood.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Dichtel says:

====================
rtnl: send notification in do_setlink()

This series ensures to call the notifier chain and to send a netlink
message when a change is done by do_setlink().

The three first patches mainly prepare the last one, which do this change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on which parameters were updated, the changes were not propagated via
the notifier chain and netlink.

The new flag has been set only when the change did not cause a call to the
notifier chain and/or to the netlink notification functions.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no functional changes with this commit, it only prepares the next one.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only effect of this patch is to print a warning if IFLA_LINKMODE is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only effect of this patch is to print a warning if IFLA_TXQLEN is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

v2 changes: add a new line after variable declaration in patch 12.

***
Patch 1 adds a few new log messages to help debugging in failure cases.

Patch 2 uses new macros for parsing RX/TX completions and TX wrbs to
help shorten the lines.

Patch 3 adds a description for the RX counter rx_input_fifo_overflow_drop.

Patch 4 adds TX completion error statistics reporting via ethtool.

Patch 5 adds a dma_mapping_error counter and its reporting via ethtool.

Patch 6 fixes up log messages in the Lancer FW download path.

Patch 7 replaces gotos with direct return statements.

Patch 8 cleans up be_change_mtu() code by using a new macro BE_MAX_MTU

Patch 9 makes be_cmd_get_regs() routine to return an integer status
similar to other FW cmd routines in be_cmds.c

Patch 10 gets rid of TX budget as enforcing a budget on TX completion
processing in NAPI is neither suggested nor it provides a performance benefit.

Patch 11 defines and uses a new macro for_all_tx_queues_on_eq() similar
to the RX processing code.

Patch 12 queries max_tx_qs from the FW for BE3 super-nic profiles.
For those profiles, the driver cannot assume a constant BE3_MAX_TX_QS value,
as the value may change for each function.

Please consider applying this patch set to the net-next tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the BE3 super-nic profile, the max_tx_qs value can vary for each function.
So the driver needs to query this value from FW instead of using the
pre-defined constant BE3_MAX_TX_QS.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the for() loop that traverses all the TX queues on an EQ
with the macro for_all_tx_queues_on_eq(). With this expalnatory
name, the one line comment is not required anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enforcing a budget on the TX completion processing in NAPI doesn't
benefit performance in anyway. Just get rid of it.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu()
more readable.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In cases where there is no extra code to handle an error, this patch replaces
gotos with a direct return statement.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Log messages in the Lancer FW download path have issues such as:
- a single message spanning multiple lines
- the success message is logged even in failure cases
- status codes are already logged in the FW cmd routines
This patch fixes these issues.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a dma_mapping_error counter to count the number of packets dropped
due to DMA mapping errors.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>