- 25 Oct, 2021 40 commits
-
-
Luo Jie authored
Add the qca8081 phy driver config_init function, which includes: 1. Enable fast restrain. 2. Add 802.3az configurations. 3. Initialize ADC threshold as 100mv. Signed-off-by:
Luo Jie <luoj@codeaurora.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Luo Jie authored
Add generic fast retrain auto-negotiation function for C45 PHYs. Signed-off-by:
-
Luo Jie authored
Add the constants for 2.5G fast retrain capability in 10G AN control register, fast retrain status and control register and THP bypass register into mdio.h. Signed-off-by:
-
Luo Jie authored
Reuse at803x phy driver config_aneg excepting adding 2500M auto-negotiation. Signed-off-by:
-
Luo Jie authored
Reuse the at803x phy driver get_features excepting adding 2500M capability. Signed-off-by:
-
Luo Jie authored
1. Separate the function at803x_read_specific_status from the at803x_read_status, since it can be reused by the read_status of qca8081 phy driver excepting adding the 2500M speed. 2. Add the qca8081 read_status function qca808x_read_status. Signed-off-by:
-
Luo Jie authored
qca8081 is a single port ethernet phy chip that supports 10/100/1000/2500 Mbps mode. Add the basic phy driver features, and reuse the at803x phy driver functions. Signed-off-by:
-
Luo Jie authored
Use GENMASK() for the current speed value. Signed-off-by:
-
Luo Jie authored
The wol feature is controlled by the MMD3.8012 bit5, need to set this bit when the wol function is enabled. The reg18 bit0 is for enabling WOL interrupt, when wol occurs, the wol interrupt status reg19 bit0 is set to 1. Call phy_trigger_machine if there are any other interrupt pending in the function set_wol. Signed-off-by:
-
Luo Jie authored
Convert at803x_set_wol to use phy_modify. Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Luo Jie authored
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h. Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: updates for -next This series includes some updates for the HNS3 ethernet driver. for it. off. ==================== Signed-off-by: -
Jiaran Zhang authored
This patch adds himac error recovery module, link_error type and ptp_error type for himac. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Weihang Li authored
This patch adds one ras error of bus related for roce, this error including RRESP/BRESP and read poison error. Signed-off-by:
Weihang Li <liweihang@huawei.com> Signed-off-by:
-
Guangbin Huang authored
Currently, the ethtool advertised link modes of FIBRE port is cleared to zero when autoneg is off, so user can not get the advertised link modes info directly from "ethtool <dev>" command. In order to ameliorate this situation, update data of speeds, fec and pause of advertised link modes when autoneg is off. Signed-off-by:
-
Guangbin Huang authored
The functions of converting speed ability to ethtool link mode just support setting mac->supported currently, to reuse these functions to set ethtool link mode for others(i.e. advertising), delete the argument mac and add argument link_mode. Signed-off-by:
-
Guangbin Huang authored
The mac statistics add pause/pfc durations in device version V3, we can get total active cycle of pause/pfc from these durations. As driver gets register number from firmware to calculate desc number to query mac statistics, it needs to set mac statistics extended enable bit in firmware command 0x701A to tell firmware that driver supports extended mac statistics, otherwise firmware only returns register number of version V1. As pause/pfc durations are not supported by hardware of old version, they should not been shown in command "ethtool -S ethX" in this case, so add checking max register number of each mac statistic in their version. If the max register number of one mac statistic is greater than register number got from firmware, it means hardware does not support this mac statistic, so ignore this statistic when get string and data of mac statistic. Signed-off-by:
-
Guangbin Huang authored
Currently, driver queries number of mac statistics before querying mac statistics. As the number of mac statistics is a fixed value in firmware, it is redundant to query this number everytime before querying mac statistics, it can just be queried once in initialization process and saved in device specifications. Signed-off-by:
-
Guangbin Huang authored
After querying mac statistics from firmware, driver copies data from descriptors to struct mac_stats of hdev, and the number of copied data is just according to the register number queried from firmware. There is a problem that if the register number queried from firmware is larger than data number of struct mac_stats, it will cause a copy overflow. So if the firmware adds more mac statistics in later version, it is not compatible with driver of old version. To fix this problem, the number of copied data needs to be used the minimum value between the register number queried from firmware and data number of struct mac_stats. The first descriptor has three data and there is one reserved, to optimize the copy process, add this reserverd data to struct mac_stats. Signed-off-by:
-
Huazhong Tan authored
Since user may need to check the current configuration of the interrupt coalesce, so add debugfs support for query this info. Create a single file "coalesce_info" for it, and query it by "cat coalesce_info", return the result to userspace. For device whose version is above V3(include V3), the GL's register contains usecs and 1us unit configuration. When get the usecs configuration from this register, it will include the confusing unit configuration, so add a GL mask to get the correct value, and add a QL mask for the frames configuration as well. The display style is below: $ cat coalesce_info tx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 4 EQE ON_TOP 0... 1 START 3 EQE LEFT 1... rx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 3 EQE LEFT 1... 1 IN_PROG 0 EQE ON_TOP 0... Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: updates 2021-10-25 please apply the following patch series for qeth to netdev's net-next tree. This brings some minor maintenance improvements, and a bunch of cleanups so that the W=1 build passes without warning. ==================== Signed-off-by: -
Julian Wiedmann authored
qeth_add_hw_header() is missing documentation for some of its parameters, fix that up. Reported-by:
Heiko Carstens <hca@linux.ibm.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Heiko Carstens authored
Fix kernel doc comments and remove incorrect kernel doc indicators. Acked-by:
-
Heiko Carstens authored
Allow the compiler to recognize and check format strings and parameters. As reported with allmodconfig and W=1: drivers/s390/net/qeth_core_main.c: In function ‘qeth_dbf_longtext’: drivers/s390/net/qeth_core_main.c:6190:9: error: function ‘qeth_dbf_longtext’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format] 6190 | vsnprintf(dbf_txt_buf, sizeof(dbf_txt_buf), fmt, args); | ^~~~~~~~~ Acked-by: -
Heiko Carstens authored
Various format strings don't match with types of parameters. Fix all of them. Acked-by:
-
Julian Wiedmann authored
The only actual user of qdio.no_input_queues is qeth_qdio_establish(), and there we already have full awareness of the current Input Queue configuration (1 RX queue, plus potentially 1 TX Completion queue). So avoid this state tracking, and the ambiguity it brings with it. Signed-off-by:
-
Julian Wiedmann authored
For none of the users we are under risk of running in HW IRQ context or or with IRQs disabled. Thus we always end up in consume_skb(). But the two occurences in the RX path should really report the dropped packet to dropmon, so have them use kfree_skb() instead. That's also consistent with what napi_free_frags() does internally. Signed-off-by:
-
Julian Wiedmann authored
qdio.ko no longer needs to care about how the QAOBs are allocated, from its perspective they are merely another parameter to do_QDIO(). So for a start, shift the cache into the only qdio driver that uses QAOBs (ie. qeth). Here there's further opportunity to optimize its usage in the future - eg. make it per-{device, TX queue}, or only compile it when the driver is built with CQ/QAOB support. Signed-off-by:Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
With commit 18787eee ("qeth: use ndo_siocdevprivate") this callback is now actually used to handle transport mode-specific _private_ ioctls. We only have such ioctls for L3 devices. So wire up a L3-specific .ndo_siocdevprivate() callback that handles those ioctls, and defers to the core qeth_siocdevprivate() for all other private ioctls. This takes the discipline one step closer to its original purpose of providing an internal extension for the qeth_core_ccwgroup_driver. Signed-off-by:
-
Julian Wiedmann authored
Add the failed MAC address into the trace message. Also fix up one format string to use %x instead of %u for the CARD_DEVID. Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Drop rtnl_lock from DSA .port_fdb_{add,del} As mentioned in the RFC posted 2 months ago: https://patchwork.kernel.org/project/netdevbpf/cover/20210824114049.3814660-1-vladimir.oltean@nxp.com/ DSA is transitioning to a driver API where the rtnl_lock is not held when calling ds->ops->port_fdb_add() and ds->ops->port_fdb_del(). Drivers cannot take that lock privately from those callbacks either. This change is required so that DSA can wait for switchdev FDB work items to finish before leaving the bridge. That change will be made in a future patch series. A small selftest is provided with the patch set in the hope that concurrency issues uncovered by this series, but not spotted by me by code inspection, will be caught. A status of the existing drivers: - mv88e6xxx_port_fdb_add() and mv88e6xxx_port_fdb_del() take mv88e6xxx_reg_lock() so they should be safe. - qca8k_fdb_add() and qca8k_fdb_del() take mutex_lock(&priv->reg_mutex) so they should be safe. - hellcreek_fdb_add() and hellcreek_fdb_add() take mutex_lock(&hellcreek->reg_lock) so they should be safe. - ksz9477_port_fdb_add() and ksz9477_port_fdb_del() take mutex_lock(&dev->alu_mutex) so they should be safe. - b53_fdb_add() and b53_fdb_del() did not have locking, so I've added a scheme based on my own judgement there (not tested). - felix_fdb_add() and felix_fdb_del() did not have locking, I've added and tested a locking scheme there. - mt7530_port_fdb_add() and mt7530_port_fdb_del() take mutex_lock(&priv->reg_mutex), so they should be safe. - gswip_port_fdb() did not have locking, so I've added a non-expert locking scheme based on my own judgement (not tested). - lan9303_alr_add_port() and lan9303_alr_del_port() take mutex_lock(&chip->alr_mutex) so they should be safe. - sja1105_fdb_add() and sja1105_fdb_del() did not have locking, I've added and tested a locking scheme. Changes in v3: Unlock arl_mutex only once in b53_fdb_dump(). Changes in v4: - Use __must_hold in ocelot and b53 - Add missing mutex_init in lantiq_gswip - Clean up the selftest a bit. Changes in v5: - Replace __must_hold with a comment. - Add a new patch (01/10). ==================== Signed-off-by: -
Vladimir Oltean authored
This test is a bit strange in that it is perhaps more manual than others: it does not transmit a clear OK/FAIL verdict, because user space does not have synchronous feedback from the kernel. If a hardware access fails, it is in deferred context. Nonetheless, on sja1105 I have used it successfully to find and solve a concurrency issue, so it can be used as a starting point for other driver maintainers too. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
These programs are useful, but not all selftests require them. Additionally, on embedded boards without package management (things like buildroot), installing mausezahn or jq is not always as trivial as downloading a package from the web. So it is actually a bit annoying to require programs that are not used. Introduce options that can be set by scripts to not enforce these dependencies. For compatibility, default to "yes". Cc: Nikolay Aleksandrov <nikolay@nvidia.com> Cc: Ido Schimmel <idosch@nvidia.com> Cc: Guillaume Nault <gnault@redhat.com> Cc: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Vladimir Oltean authored
After talking with Ido Schimmel, it became clear that rtnl_lock is not actually required for anything that is done inside the SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE deferred work handlers. The reason why it was probably added by Arkadi Sharshevsky in commit c9eb3e0f ("net: dsa: Add support for learning FDB through notification") was to offer the same locking/serialization guarantees as .ndo_fdb_{add,del} and avoid reworking any drivers. DSA has implemented .ndo_fdb_add and .ndo_fdb_del until commit b117e1e8 ("net: dsa: delete dsa_legacy_fdb_add and dsa_legacy_fdb_del") - that is to say, until fairly recently. But those methods have been deleted, so now we are free to drop the rtnl_lock as well. Note that exposing DSA switch drivers to an unlocked method which was previously serialized by the rtnl_mutex is a potentially dangerous affair. Driver writers couldn't ensure that their internal locking scheme does the right thing even if they wanted. We could err on the side of paranoia and introduce a switch-wide lock inside the DSA framework, but that seems way overreaching. Instead, we could check as many drivers for regressions as we can, fix those first, then let this change go in once it is assumed to be fairly safe. Signed-off-by: -
Vladimir Oltean authored
Now that the rtnl_mutex is going away for dsa_port_{host_,}fdb_{add,del}, no one is serializing access to the address lists that DSA keeps for the purpose of reference counting on shared ports (CPU and cascade ports). It can happen for one dsa_switch_do_fdb_del to do list_del on a dp->fdbs element while another dsa_switch_do_fdb_{add,del} is traversing dp->fdbs. We need to avoid that. Currently dp->mdbs is not at risk, because dsa_switch_do_mdb_{add,del} still runs under the rtnl_mutex. But it would be nice if it would not depend on that being the case. So let's introduce a mutex per port (the address lists are per port too) and share it between dp->mdbs and dp->fdbs. The place where we put the locking is interesting. It could be tempting to put a DSA-level lock which still serializes calls to .port_fdb_{add,del}, but it would still not avoid concurrency with other driver code paths that are currently under rtnl_mutex (.port_fdb_dump, .port_fast_age). So it would add a very false sense of security (and adding a global switch-wide lock in DSA to resynchronize with the rtnl_lock is also counterproductive and hard). So the locking is intentionally done only where the dp->fdbs and dp->mdbs lists are traversed. That means, from a driver perspective, that .port_fdb_add will be called with the dp->addr_lists_lock mutex held on the CPU port, but not held on user ports. This is done so that driver writers are not encouraged to rely on any guarantee offered by dp->addr_lists_lock. Signed-off-by: -
Vladimir Oltean authored
The GSWIP switch accesses various bridging layer tables (VLANs, FDBs, forwarding rules) indirectly through PCE registers. These hardware accesses are non-atomic, being comprised of several register reads and writes. These accesses are currently serialized by the rtnl_lock, but DSA is changing its driver API and that lock will no longer be held when calling ->port_fdb_add() and ->port_fdb_del(). So this driver needs to serialize the access to the PCE registers using its own locking scheme. This patch adds that. Note that the driver also uses the gswip_pce_load_microcode() function to load a static configuration for the packet classification engine into a table using the same registers. It is currently not protected, but since that configuration is only done from the dsa_switch_ops :: setup method, there is no risk of it being concurrent with other operations. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Vladimir Oltean authored
The b53 driver performs non-atomic transactions to the ARL table when adding, deleting and reading FDB and MDB entries. Traditionally these were all serialized by the rtnl_lock(), but now it is possible that DSA calls ->port_fdb_add and ->port_fdb_del without holding that lock. So the driver must have its own serialization logic. Add a mutex and hold it from all entry points (->port_fdb_{add,del,dump}, ->port_mdb_{add,del}). Signed-off-by: -
Vladimir Oltean authored
DSA would like to remove the rtnl_lock from its SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses the same MAC table functions as ocelot. This means that the MAC table functions will no longer be implicitly serialized with respect to each other by the rtnl_mutex, we need to add a dedicated lock in ocelot for the non-atomic operations of selecting a MAC table row, reading/writing what we want and polling for completion. Signed-off-by: -
Vladimir Oltean authored
The sja1105 hardware seems as concurrent as can be, but when we create a background script that adds/removes a rain of FDB entries without the rtnl_mutex taken, then in parallel we do another operation like run 'bridge fdb show', we can notice these errors popping up: sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2 sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2 Luckily what is going on does not require a major rework in the driver. The sja1105_dynamic_config_read() function sends multiple SPI buffers to the peripheral until the operation completes. We should not do anything until the hardware clears the VALID bit. But since there is no locking (i.e. right now we are implicitly serialized by the rtnl_mutex, but if we remove that), it might be possible that the process which performs the dynamic config read is preempted and another one performs a dynamic config write. What will happen in that case is that sja1105_dynamic_config_read(), when it resumes, expects to see VALIDENT set for the entry it reads back. But it won't. This can be corrected by introducing a mutex for serializing SPI accesses to the dynamic config interface which should be atomic with respect to each other. Signed-off-by:
-
Vladimir Oltean authored
The hardware manual says that software should attempt a new dynamic config access (be it a a write or a read-back) only while the VALID bit is cleared. The VALID bit is set by software to 1, and it remains set as long as the hardware is still processing the request. Currently the driver only polls for the command completion only for reads, because that's when we need the actual data read back. Writes have been more or less "asynchronous", although this has never been an observable issue. This change makes sja1105_dynamic_config_write poll the VALID bit as well, to absolutely ensure that a follow-up access to the static config finds the VALID bit cleared. So VALID means "work in progress", while VALIDENT means "entry being read is valid". On reads we check the VALIDENT bit too, while on writes that bit is not always defined. So we need to factor it out of the loop, and make the loop provide back the unpacked command structure, so that sja1105_dynamic_config_read can check the VALIDENT bit. The change also attempts to convert the open-coded loop to use the read_poll_timeout macro, since I know this will come up during review. It's more code, but hey, it uses read_poll_timeout! Tested on SJA1105T, SJA1105S, SJA1110A. Signed-off-by:
-
