- 18 Jul, 2023 9 commits
-
-
Fabio Estevam authored
scl-gpios and sda-gpios need GPIO_OPEN_DRAIN flag, otherwise the following run-time warning is seen: gpio-144 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file gpio-146 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Michael Walle authored
Now that it is finally possible to get the MAC addresses from the OTP memory, use it to set the addresses of the network devices. There are 8 reserved MAC addresses in total per board. Distribute them as follows: +----------+------+------+------+------+------+ | | var1 | var2 | var3 | var4 | kbox | +----------+------+------+------+------+------+ | enetc #0 | +0 | | | +0 | +0 | | enetc #1 | | | +0 | +1 | +1 | | enetc #2 | | +2 | | | +2 | | enetc #3 | | +3 | | | +3 | | felix p0 | | +0 | | | +4 | | felix p1 | | +1 | | | +5 | | felix p2 | | | | | +6 | | felix p3 | | | | | +7 | | felix p4 | | | | | | | felix p5 | | | | | | +----------+------+------+------+------+------+ An empty cell means, the port is not available and thus doesn't need an ethernet address. Signed-off-by: Michael Walle <mwalle@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Cem Tenruh authored
Add i2c4 sda-/scl-gpios with the corresponding pinmux entries. Signed-off-by: Cem Tenruh <c.tenruh@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Yannic Moog authored
Set Pull Resistors Enable bit to put signal into a defined state. Signed-off-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Cem Tenruh <c.tenruh@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Yannic Moog authored
Add #address-cells and #size-cells properties to som_flash. This enables correct parsing of added SPI NOR mtd partition child nodes that are set in the bootloader. Signed-off-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Cem Tenruh <c.tenruh@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Yashwanth Varakala authored
Add TPM node for phyBOARD-Polis i.MX 8M Mini which has the Infineon-SLB 9670 TPM2.0 module populated. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Cem Tenruh <c.tenruh@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Adam Ford authored
The Beacon Embedded imx8mm development kit has a DSI to HDMI bridge chip. The bridge supports stereo audio and hot-plugging. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Adam Ford authored
The DSI to HDMI bridge uses the address currently assigned to the camera, so change the camera address to the alternative address of 0x10 in preparation to enable the bridge. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Adam Ford authored
The Beacon Embedded imx8mn development kit has a DSI to HDMI bridge chip. The bridge supports stereo audio and hot-plug detection. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 17 Jul, 2023 6 commits
-
-
Tim Harvey authored
Fix typo in imx8mm-venice-gw72xx-0x-imx219 overlay causing it to use gw73xx configuration. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Tim Harvey authored
Update the imx8mp-venice-gw74xx for revB: - add CAN1 - add TIS-TPM on SPI2 - add FAN controller - fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for backward compatible option) - M2 socket GPIO's moved Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Tim Harvey authored
On the GW7904 uart1 can use UART3_TX/RX for hardware flow control which was the desired default configuration. Remove uart3 and configure uart1 for hardware flow control. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Tim Harvey authored
The GW7902 has a Murata LBEE5H 802.11abgnac / BT5 module based on the Cypress CYW43455 which supports SDR50/SDR104. Add dt pinctrl for the 100mhz and 200mhz states to support SDR50/SDR104. While at it add the dt node for the CYW43455 wifi. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Tim Harvey authored
The GW7901 has a Murata LBEE5H 802.11abgnac / BT5 module based on the Cypress CYW43455 which supports SDR50/SDR104. Add dt pinctrl for the 100mhz and 200mhz states to support SDR50/SDR104. While at it add the dt node for the CYW43455 wifi for the brcmfmac driver. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Tim Harvey authored
Add regulator config for cpu-supply in order to support cpufreq. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 16 Jul, 2023 1 commit
-
-
Fabio Estevam authored
'power-supply' is an invalid property for usdhc and it gives the following schema warning: imx8mq-librem5-r2.dtb: mmc@30b40000: Unevaluated properties are not allowed ('power-supply' was unexpected) From schema: Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml Change it to 'vqmmc-supply', which represents the supply for the bus IO. Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 09 Jul, 2023 10 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
We just sorted the entries and fields last release, so just out of a perverse sense of curiosity, I decided to see if we can keep things ordered for even just one release. The answer is "No. No we cannot". I suggest that all kernel developers will need weekly training sessions, involving a lot of Big Bird and Sesame Street. And at the yearly maintainer summit, we will all sing the alphabet song together. I doubt I will keep doing this. At some point "perverse sense of curiosity" turns into just a cold dark place filled with sadness and despair. Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull dma-mapping fixes from Christoph Hellwig: - swiotlb area sizing fixes (Petr Tesarik) * tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping: swiotlb: reduce the number of areas to match actual memory pool size swiotlb: always set the number of areas before allocating the pool
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq update from Borislav Petkov: - Optimize IRQ domain's name assignment * tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqdomain: Use return value of strreplace()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fpu fix from Borislav Petkov: - Do FPU AP initialization on Xen PV too which got missed by the recent boot reordering work * tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/xen: Fix secondary processors' FPU initialization
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fix from Thomas Gleixner: "A single fix for the mechanism to park CPUs with an INIT IPI. On shutdown or kexec, the kernel tries to park the non-boot CPUs with an INIT IPI. But the same code path is also used by the crash utility. If the CPU which panics is not the boot CPU then it sends an INIT IPI to the boot CPU which resets the machine. Prevent this by validating that the CPU which runs the stop mechanism is the boot CPU. If not, leave the other CPUs in HLT" * tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/smp: Don't send INIT to boot CPU
-
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds authored
Pull MIPS fixes from Thomas Bogendoerfer: - fixes for KVM - fix for loongson build and cpu probing - DT fixes * tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled MIPS: dts: add missing space before { MIPS: Loongson: Fix build error when make modules_install MIPS: KVM: Fix NULL pointer dereference MIPS: Loongson: Fix cpu_probe_loongson() again
-
git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds authored
Pull xfs fix from Darrick Wong: "Nothing exciting here, just getting rid of a gcc warning that I got tired of seeing when I turn on gcov" * tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: fix uninit warning in xfs_growfs_data
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull more smb client updates from Steve French: - fix potential use after free in unmount - minor cleanup - add worker to cleanup stale directory leases * tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Add a laundromat thread for cached directories smb: client: remove redundant pointer 'server' cifs: fix session state transition to avoid use-after-free issue
-
https://github.com/jonmason/ntbLinus Torvalds authored
Pull NTB updates from Jon Mason: "Fixes for pci_clean_master, error handling in driver inits, and various other issues/bugs" * tag 'ntb-6.5' of https://github.com/jonmason/ntb: ntb: hw: amd: Fix debugfs_create_dir error checking ntb.rst: Fix copy and paste error ntb_netdev: Fix module_init problem ntb: intel: Remove redundant pci_clear_master ntb: epf: Remove redundant pci_clear_master ntb_hw_amd: Remove redundant pci_clear_master ntb: idt: drop redundant pci_enable_pcie_error_reporting() MAINTAINERS: git://github -> https://github.com for jonmason NTB: EPF: fix possible memory leak in pci_vntb_probe() NTB: ntb_tool: Add check for devm_kcalloc NTB: ntb_transport: fix possible memory leak while device_register() fails ntb: intel: Fix error handling in intel_ntb_pci_driver_init() NTB: amd: Fix error handling in amd_ntb_pci_driver_init() ntb: idt: Fix error handling in idt_pci_driver_init()
-
- 08 Jul, 2023 14 commits
-
-
Hugh Dickins authored
Lockdep is certainly right to complain about (&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f but task is already holding lock: (&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db Invert those to the usual ordering. Fixes: 33313a74 ("mm: lock newly mapped VMA which can be modified after it becomes visible") Cc: stable@vger.kernel.org Signed-off-by: Hugh Dickins <hughd@google.com> Tested-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull hotfixes from Andrew Morton: "16 hotfixes. Six are cc:stable and the remainder address post-6.4 issues" The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since it was all hopefully fixed in mainline. * tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: lib: dhry: fix sleeping allocations inside non-preemptable section kasan, slub: fix HW_TAGS zeroing with slub_debug kasan: fix type cast in memory_is_poisoned_n mailmap: add entries for Heiko Stuebner mailmap: update manpage link bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page MAINTAINERS: add linux-next info mailmap: add Markus Schneider-Pargmann writeback: account the number of pages written back mm: call arch_swap_restore() from do_swap_page() squashfs: fix cache race with migration mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison docs: update ocfs2-devel mailing list address MAINTAINERS: update ocfs2-devel mailing list address mm: disable CONFIG_PER_VMA_LOCK until its fixed fork: lock VMAs of the parent process when forking
-
Suren Baghdasaryan authored
When forking a child process, the parent write-protects anonymous pages and COW-shares them with the child being forked using copy_present_pte(). We must not take any concurrent page faults on the source vma's as they are being processed, as we expect both the vma and the pte's behind it to be stable. For example, the anon_vma_fork() expects the parents vma->anon_vma to not change during the vma copy. A concurrent page fault on a page newly marked read-only by the page copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the source vma, defeating the anon_vma_clone() that wasn't done because the parent vma originally didn't have an anon_vma, but we now might end up copying a pte entry for a page that has one. Before the per-vma lock based changes, the mmap_lock guaranteed exclusion with concurrent page faults. But now we need to do a vma_start_write() to make sure no concurrent faults happen on this vma while it is being processed. This fix can potentially regress some fork-heavy workloads. Kernel build time did not show noticeable regression on a 56-core machine while a stress test mapping 10000 VMAs and forking 5000 times in a tight loop shows ~5% regression. If such fork time regression is unacceptable, disabling CONFIG_PER_VMA_LOCK should restore its performance. Further optimizations are possible if this regression proves to be problematic. Suggested-by: David Hildenbrand <david@redhat.com> Reported-by: Jiri Slaby <jirislaby@kernel.org> Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com> Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/Reported-by: Jacob Young <jacobly.alt@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624 Fixes: 0bff0aae ("x86/mm: try VMA lock-based page fault handling first") Cc: stable@vger.kernel.org Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Suren Baghdasaryan authored
mmap_region adds a newly created VMA into VMA tree and might modify it afterwards before dropping the mmap_lock. This poses a problem for page faults handled under per-VMA locks because they don't take the mmap_lock and can stumble on this VMA while it's still being modified. Currently this does not pose a problem since post-addition modifications are done only for file-backed VMAs, which are not handled under per-VMA lock. However, once support for handling file-backed page faults with per-VMA locks is added, this will become a race. Fix this by write-locking the VMA before inserting it into the VMA tree. Other places where a new VMA is added into VMA tree do not modify it after the insertion, so do not need the same locking. Cc: stable@vger.kernel.org Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Suren Baghdasaryan authored
With recent changes necessitating mmap_lock to be held for write while expanding a stack, per-VMA locks should follow the same rules and be write-locked to prevent page faults into the VMA being expanded. Add the necessary locking. Cc: stable@vger.kernel.org Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull more SCSI updates from James Bottomley: "A few late arriving patches that missed the initial pull request. It's mostly bug fixes (the dt-bindings is a fix for the initial pull)" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: ufs: core: Remove unused function declaration scsi: target: docs: Remove tcm_mod_builder.py scsi: target: iblock: Quiet bool conversion warning with pr_preempt use scsi: dt-bindings: ufs: qcom: Fix ICE phandle scsi: core: Simplify scsi_cdl_check_cmd() scsi: isci: Fix comment typo scsi: smartpqi: Replace one-element arrays with flexible-array members scsi: target: tcmu: Replace strlcpy() with strscpy() scsi: ncr53c8xx: Replace strlcpy() with strscpy() scsi: lpfc: Fix lpfc_name struct packing
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull more i2c updates from Wolfram Sang: - xiic patch should have been in the original pull but slipped through - mpc patch fixes a build regression - nomadik cleanup * tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: mpc: Drop unused variable i2c: nomadik: Remove a useless call in the remove function i2c: xiic: Don't try to handle more interrupt events after error
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull hardening fixes from Kees Cook: - Check for NULL bdev in LoadPin (Matthias Kaehlcke) - Revert unwanted KUnit FORTIFY build default - Fix 1-element array causing boot warnings with xhci-hub * tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array Revert "fortify: Allow KUnit test to build without FORTIFY" dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter
-
Anup Sharma authored
The debugfs_create_dir function returns ERR_PTR in case of error, and the only correct way to check if an error occurred is 'IS_ERR' inline function. This patch will replace the null-comparison with IS_ERR. Signed-off-by: Anup Sharma <anupnewsmail@gmail.com> Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
-
Linus Torvalds authored
Merge tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next Pull more perf tools updates from Namhyung Kim: "These are remaining changes and fixes for this cycle. Build: - Allow generating vmlinux.h from BTF using `make GEN_VMLINUX_H=1` and skip if the vmlinux has no BTF. - Replace deprecated clang -target xxx option by --target=xxx. perf record: - Print event attributes with well known type and config symbols in the debug output like below: # perf record -e cycles,cpu-clock -C0 -vv true <SNIP> ------------------------------------------------------------ perf_event_attr: type 0 (PERF_TYPE_HARDWARE) size 136 config 0 (PERF_COUNT_HW_CPU_CYCLES) { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|CPU|PERIOD|IDENTIFIER read_format ID disabled 1 inherit 1 freq 1 sample_id_all 1 exclude_guest 1 ------------------------------------------------------------ sys_perf_event_open: pid -1 cpu 0 group_fd -1 flags 0x8 = 5 ------------------------------------------------------------ perf_event_attr: type 1 (PERF_TYPE_SOFTWARE) size 136 config 0 (PERF_COUNT_SW_CPU_CLOCK) { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|CPU|PERIOD|IDENTIFIER read_format ID disabled 1 inherit 1 freq 1 sample_id_all 1 exclude_guest 1 - Update AMD IBS event error message since it now support per-process profiling but no priviledge filters. $ sudo perf record -e ibs_op//k -C 0 Error: AMD IBS doesn't support privilege filtering. Try again without the privilege modifiers (like 'k') at the end. perf lock contention: - Support CSV style output using -x option $ sudo perf lock con -ab -x, sleep 1 # output: contended, total wait, max wait, avg wait, type, caller 19, 194232, 21415, 10222, spinlock, process_one_work+0x1f0 15, 162748, 23843, 10849, rwsem:R, do_user_addr_fault+0x40e 4, 86740, 23415, 21685, rwlock:R, ep_poll_callback+0x2d 1, 84281, 84281, 84281, mutex, iwl_mvm_async_handlers_wk+0x135 8, 67608, 27404, 8451, spinlock, __queue_work+0x174 3, 58616, 31125, 19538, rwsem:W, do_mprotect_pkey+0xff 3, 52953, 21172, 17651, rwlock:W, do_epoll_wait+0x248 2, 30324, 19704, 15162, rwsem:R, do_madvise+0x3ad 1, 24619, 24619, 24619, spinlock, rcu_core+0xd4 - Add --output option to save the data to a file not to be interfered by other debug messages. Test: - Fix event parsing test on ARM where there's no raw PMU nor supports PERF_PMU_CAP_EXTENDED_HW_TYPE. - Update the lock contention test case for CSV output. - Fix a segfault in the daemon command test. Vendor events (JSON): - Add has_event() to check if the given event is available on system at runtime. On Intel machines, some transaction events may not be present when TSC extensions are disabled. - Update Intel event metrics. Misc: - Sort symbols by name using an external array of pointers instead of a rbtree node in the symbol. This will save 16-bytes or 24-bytes per symbol whether the sorting is actually requested or not. - Fix unwinding DWARF callstacks using libdw when --symfs option is used" * tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next: (38 commits) perf test: Fix event parsing test when PERF_PMU_CAP_EXTENDED_HW_TYPE isn't supported. perf test: Fix event parsing test on Arm perf evsel amd: Fix IBS error message perf: unwind: Fix symfs with libdw perf symbol: Fix uninitialized return value in symbols__find_by_name() perf test: Test perf lock contention CSV output perf lock contention: Add --output option perf lock contention: Add -x option for CSV style output perf lock: Remove stale comments perf vendor events intel: Update tigerlake to 1.13 perf vendor events intel: Update skylakex to 1.31 perf vendor events intel: Update skylake to 57 perf vendor events intel: Update sapphirerapids to 1.14 perf vendor events intel: Update icelakex to 1.21 perf vendor events intel: Update icelake to 1.19 perf vendor events intel: Update cascadelakex to 1.19 perf vendor events intel: Update meteorlake to 1.03 perf vendor events intel: Add rocketlake events/metrics perf vendor metrics intel: Make transaction metrics conditional perf jevents: Support for has_event function ...
-
https://github.com/norov/linuxLinus Torvalds authored
Pull bitmap updates from Yury Norov: "Fixes for different bitmap pieces: - lib/test_bitmap: increment failure counter properly The tests that don't use expect_eq() macro to determine that a test is failured must increment failed_tests explicitly. - lib/bitmap: drop optimization of bitmap_{from,to}_arr64 bitmap_{from,to}_arr64() optimization is overly optimistic on 32-bit LE architectures when it's wired to bitmap_copy_clear_tail(). - nodemask: Drop duplicate check in for_each_node_mask() As the return value type of first_node() became unsigned, the node >= 0 became unnecessary. - cpumask: fix function description kernel-doc notation - MAINTAINERS: Add bits.h and bitfield.h to the BITMAP API record Add linux/bits.h and linux/bitfield.h for visibility" * tag 'bitmap-6.5-rc1' of https://github.com/norov/linux: MAINTAINERS: Add bitfield.h to the BITMAP API record MAINTAINERS: Add bits.h to the BITMAP API record cpumask: fix function description kernel-doc notation nodemask: Drop duplicate check in for_each_node_mask() lib/bitmap: drop optimization of bitmap_{from,to}_arr64 lib/test_bitmap: increment failure counter properly
-
Geert Uytterhoeven authored
The Smatch static checker reports the following warnings: lib/dhry_run.c:38 dhry_benchmark() warn: sleeping in atomic context lib/dhry_run.c:43 dhry_benchmark() warn: sleeping in atomic context Indeed, dhry() does sleeping allocations inside the non-preemptable section delimited by get_cpu()/put_cpu(). Fix this by using atomic allocations instead. Add error handling, as atomic these allocations may fail. Link: https://lkml.kernel.org/r/bac6d517818a7cd8efe217c1ad649fffab9cc371.1688568764.git.geert+renesas@glider.be Fixes: 13684e96 ("lib: dhry: fix unstable smp_processor_id(_) usage") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/0469eb3a-02eb-4b41-b189-de20b931fa56@moroto.mountainSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-
Andrey Konovalov authored
Commit 946fa0db ("mm/slub: extend redzone check to extra allocated kmalloc space than requested") added precise kmalloc redzone poisoning to the slub_debug functionality. However, this commit didn't account for HW_TAGS KASAN fully initializing the object via its built-in memory initialization feature. Even though HW_TAGS KASAN memory initialization contains special memory initialization handling for when slub_debug is enabled, it does not account for in-object slub_debug redzones. As a result, HW_TAGS KASAN can overwrite these redzones and cause false-positive slub_debug reports. To fix the issue, avoid HW_TAGS KASAN memory initialization when slub_debug is enabled altogether. Implement this by moving the __slub_debug_enabled check to slab_post_alloc_hook. Common slab code seems like a more appropriate place for a slub_debug check anyway. Link: https://lkml.kernel.org/r/678ac92ab790dba9198f9ca14f405651b97c8502.1688561016.git.andreyknvl@google.com Fixes: 946fa0db ("mm/slub: extend redzone check to extra allocated kmalloc space than requested") Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reported-by: Will Deacon <will@kernel.org> Acked-by: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: kasan-dev@googlegroups.com Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Collingbourne <pcc@google.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-
Andrey Konovalov authored
Commit bb6e04a1 ("kasan: use internal prototypes matching gcc-13 builtins") introduced a bug into the memory_is_poisoned_n implementation: it effectively removed the cast to a signed integer type after applying KASAN_GRANULE_MASK. As a result, KASAN started failing to properly check memset, memcpy, and other similar functions. Fix the bug by adding the cast back (through an additional signed integer variable to make the code more readable). Link: https://lkml.kernel.org/r/8c9e0251c2b8b81016255709d4ec42942dcaf018.1688431866.git.andreyknvl@google.com Fixes: bb6e04a1 ("kasan: use internal prototypes matching gcc-13 builtins") Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-