Skip to content

L
linux
Switch branch/tag
  1. 01 Mar, 2016 20 commits
  3. 29 Feb, 2016 12 commits
  5. 27 Feb, 2016 1 commit
  7. 26 Feb, 2016 7 commits
    • David S. Miller's avatar
      Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue · e1bae75d
      David S. Miller authored 
      Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2016-02-24

This series contains updates to e1000e, igb and igbvf.

Raanan provides updates for e1000e, first increases the ULP timer since it
now takes longer for the ULP exit to complete on Skylake.  Fixes the
configuration of the internal hardware PHY clock gating mechanism, which was
causing packet loss due to mis configuring.  Fixed additional ULP
configuration settings which were not being properly cleared after cable
connect in V-Pro capable systems.  Added support for more i219 devices.

Takuma Ueba provides a fix for I210 where IPv6 autoconf test sometimes
fails due to DAD NS for link-local is not transmitted.  To avoid this
issue, we need to wait until 1000BASE-T status register "Remote receiver
status OK".

Todd provides a patch to override EEPROM WoL settings for specific OEM
devices. Then renamed igb defines to be more generic, since the define
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part.

Roland Hii fixes an issue where only the half cycle time of less than or
equal to 70 millisecond uses the I210 clock output function.  His patch
adds additional conditions when half cycle time is equal to 125 or 250 or
500 millisecond to use the clock output function.

Alex Duyck adds support for generic transmit checksums for igb and igbvf.

Jon Maxwell fixes an issues where customer applications are registering
and un-registering multicast addresses every few seconds which is leading
to many "Link is up" messages in the logs as a result of the
netif_carrier_off(netdev) in igbvf_msix_other().  So remove the
link is up message when registering multicast addresses.

Corinna Vinschen provides a fix for when switching off VLAN offloading on
i350, the VLAN interface becomes unusable.

Stefan Assmann updates the driver to use ndo_stop() instead of
dev_close() when running ethtool offline self test.  Since dev_close()
causes IFF_UP to be cleared which will remove the interfaces routes
and some addresses.

v2: Dropped patches 6-10 in the original series.  Patch 6-7 added support
    for character device for AVB and based on community feedback, we do not
    want to do this.  Patches 8-10 provided fixes to the problematic code
    added in patches 6 & 7.  So all of them must go!
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e1bae75d
    • Alexander Duyck's avatar
      GSO: Provide software checksum of tunneled UDP fragmentation offload · 22463876
      Alexander Duyck authored 
      On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.

In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: default avatarAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      22463876
    • David S. Miller's avatar
      Merge branch 'vrf-saddr-selection' · c3f463ba
      David S. Miller authored 
      David Ahern says:

====================
net: l3mdev: Fix source address for unnumbered deployments

David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces. The use
case has the VRF device as the VRF local loopback with addresses and
interfaces enslaved without an address themselves. e.g,

    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

ping to the 10.2.2.2 through the L3 domain:

    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

picks up the wrong address -- the one from 'lo' not vrf0. And from tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

This patch series changes address selection to only consider devices in
the same L3 domain and to use the VRF device as the L3 domains loopback.

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c3f463ba
    • David Lamparter's avatar
      net: l3mdev: prefer VRF master for source address selection · 17b693cd
      David Lamparter authored 
      When selecting an address in context of a VRF, the vrf master should be
preferred for address selection.  If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: default avatarDavid Lamparter <equinox@diac24.net>
Signed-off-by: default avatarDavid Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      17b693cd
    • David Ahern's avatar
      net: l3mdev: address selection should only consider devices in L3 domain · 3f2fb9a8
      David Ahern authored 
      David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.

Relevant commands from his script:
    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

    tcpdump -ni dummy2 &

And using ping instead of his socat example:
    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

Note the source address is from lo and is not a VRF local address. With
this patch:

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.

The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.

IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.

Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: default avatarDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3f2fb9a8
    • Simon Horman's avatar
      can: rcar: add device tree support for r8a779[234] · f71096df
      Simon Horman authored 
      Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.

By documenting these compat stings they may be used in DTSs shipped, for
example as part of ROMs. They must be used in conjunction with the Gen2
fallback compat string. At this time there are no known differences between
the r8a779[234] IP blocks and that implemented by the driver for the Gen2
fallback compat string. Thus there is no need to update the driver as the
use of the Gen2 fallback compat string will activate the correct code in
the current driver while leaving the option for r8a779[234]-specific driver
code to be activated in an updated driver should the need arise.
Signed-off-by: default avatarSimon Horman <horms+renesas@verge.net.au>
Acked-by: default avatarGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      f71096df
    • Simon Horman's avatar
      can: rcar: add gen[12] fallback compatibility strings · 0dfa61bb
      Simon Horman authored 
      Add fallback compatibility string for R-Car Gen 1 and Gen2.

In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and Gen 2. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7779 is older than r8a7778 but that doesn't imply that the latter is a
descendant of the former or vice versa.

We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.

For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: default avatarSimon Horman <horms+renesas@verge.net.au>
Acked-by: default avatarRob Herring <robh@kernel.org>
Acked-by: default avatarGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      0dfa61bb
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7