The net_eq() check is already performed inside
devlinks_xa_for_each_registered_get() helper, so remove the redundant
appearance.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220727055912.568391-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Absolute path to other DT schema is preferred over relative one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220726115650.100726-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Change the type of cbq_set_lss to void.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220726030748.243505-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Wenjia Zhang says:

====================
net/smc: updates 2022-07-25

please apply the following patches to netdev's net-next tree.

These patches do some preparation to make ISM available for uses beyond
SMC-D, and a bunch of cleanups.

v2: add "Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, the smc and smc_diag modules were automatically loaded as
dependencies of the ism module whenever an ISM device was present.
With the pending rework of the ISM API, the smc module will no longer
automatically be loaded in presence of an ISM device. Usage of an AF_SMC
socket will still trigger loading of the smc modules, but usage of a
netlink socket will not.
This is addressed by setting the correct module aliases.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang < wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the DMBE bits, which are passed on individually in ism_move() as
parameter idx, available to the receiver.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang < wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reworked signature of the function to retrieve the system EID: No plausible
reason to use a double pointer. And neither to pass in the device as an
argument, as this identifier is by definition per system, not per device.
Plus some minor consistency edits.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang < wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This struct is used in a single place only, and its usage generates
inefficient code. Time to clean up!
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-and-tested-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang < wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arun Ramadoss says:

====================
net: dsa: microchip: add support for phylink mac config and link up

This patch series add support common phylink mac config and link up for the ksz
series switches. At present, ksz8795 and ksz9477 doesn't implement the phylink
mac config and link up. It configures the mac interface in the port setup hook.
ksz8830 series switch does not mac link configuration. For lan937x switches, in
the part support patch series has support only for MII and RMII configuration.
Some group of switches have some register address and bit fields common and
others are different. So, this patch aims to have common phylink implementation
which configures the register based on the chip id.

Changes in v2
- combined the modification of duplex, tx_pause and rx_pause into single
  function.

Changes in v1
- Squash the reading rgmii value from dt to patch which apply the rgmii value
- Created the new function ksz_port_set_xmii_speed
- Seperated the namespace values for xmii_ctrl_0 and xmii_ctrl_1 register
- Applied the rgmii delay value based on the rx/tx-internal-delay-ps
====================
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port.  It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20220725020124.5760-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

One rcu_read_unlock() should have been removed in blamed commit.

Fixes: 9b1c21d8 ("ip6mr: do not acquire mrt_lock while calling ip6_mr_forward()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220725200554.2563581-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tls: rx: decrypt from the TCP queue

This is the final part of my TLS Rx rework. It switches from
strparser to decrypting data from skbs queued in TCP. We don't
need the full strparser for TLS, its needs are very basic.
This set gives us a small but measurable (6%) performance
improvement (continuous stream).
====================

Link: https://lore.kernel.org/r/20220722235033.2594446-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

TLS is a relatively poor fit for strparser. We pause the input
every time a message is received, wait for a read which will
decrypt the message, start the parser, repeat. strparser is
built to delineate the messages, wrap them in individual skbs
and let them float off into the stack or a different socket.
TLS wants the data pages and nothing else. There's no need
for TLS to keep cloning (and occasionally skb_unclone()'ing)
the TCP rx queue.

This patch uses a pre-allocated skb and attaches the skbs
from the TCP rx queue to it as frags. TLS is careful never
to modify the input skb without CoW'ing / detaching it first.

Since we call TCP rx queue cleanup directly we also get back
the benefit of skb deferred free.

Overall this results in a 6% gain in my benchmarks.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Wrap the remaining skb_cow_data() into a helper, so it's easier
to replace down the lane. The new version will change the skb
so make sure relevant pointers get reloaded after the call.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Expose TCP rx queue accessor and cleanup, so that TLS can
decrypt directly from the TCP queue. The expectation
is that the caller can access the skb returned from
tcp_recv_skb() and up to inq bytes worth of data (some
of which may be in ->next skbs) and then call
tcp_read_done() when data has been consumed.
The socket lock must be held continuously across
those two operations.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The non-zero-copy path assumes a full skb with decrypted contents.
This means the device offload would have to CoW the data. Try
to keep the zero-copy status instead, copy the data to user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the future we'll want to reuse the input skb in case of
zero-copy so we shouldn't always free darg.skb. Move the
freeing of darg.skb into the non-zc cases. All cases will
now free ctx->recv_pkt (inside let tls_rx_rec_done()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After recent changes the SW side of tls_rx_one_record() can
be nicely encapsulated in its own function. Move the pad handling
as well. This will be useful for ->zc handling in tls_decrypt_device().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To allow for the logic to change later wrap accesses
which interrogate the input skb in helper functions.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
Implement dev info and dev flash for line cards

This patchset implements two features:
1) "devlink dev info" is exposed for line card (patches 6-9)
2) "devlink dev flash" is implemented for line card gearbox
   flashing (patch 10)

For every line card, "a nested" auxiliary device is created which
allows to bind the features mentioned above (patch 4).

The relationship between line card and its auxiliary dev devlink
is carried over extra line card netlink attribute (patches 3 and 5).

The first patch removes devlink_mutex from devlink_register/unregister()
which eliminates possible deadlock during devlink reload command. The
second patchset follows up with putting net pointer check into new
helper.

Examples:

$ devlink lc show pci/0000:01:00.0 lc 1
pci/0000:01:00.0:
  lc 1 state active type 16x100G nested_devlink auxiliary/mlxsw_core.lc.0
    supported_types:
       16x100G

$ devlink dev show auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
        fw.psid MT_0000000749
      running:
        ini.version 4
        fw 19.2010.1312

$ devlink dev flash auxiliary/mlxsw_core.lc.0 file mellanox/fw-AGB-rel-19_2010_1312-022-EVB.mfa2
====================

Link: https://lore.kernel.org/r/20220725082925.366455-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Once line card is activated, check the FW version and PSID are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Once line card is provisioned, check if HW revision and INI version
are exposed on associated nested auxiliary device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Implement flash_update() devlink op for the line card devlink instance
to allow user to update line card gearbox FW using MDDT register
and mlxfw.

Example:
$ devlink dev flash auxiliary/mlxsw_core.lc.0 file mellanox/fw-AGB-rel-19_2010_1312-022-EVB.mfa2
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use tunneled MGIR to obtain PSID of line card device and extend
device_info_get() op to fill up the info with that.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
        fw.psid MT_0000000749
      running:
        ini.version 4
        fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MDDT register allows to deliver query and request messages (PRM
registers, commands) to a DownStream device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case the line card is active, go over all possible existing
devices (gearboxes) on it and expose FW version of the flashable one.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
      running:
        ini.version 4
        fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend existing MDDQ register by possibility to query information about
devices residing on a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Implement info_get() to expose HW revision of a linecard and loaded INI
version.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
      running:
        ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to be eventually able to expose line card gearbox version and
possibility to flash FW, model the line card as a separate device on
auxiliary bus.

Add the auxiliary device for provisioned line card in order to be able
to expose provisioned line card info over devlink dev info. When the
line card becomes active, there may be other additional info added to
the output.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For the purpose of exposing device info and allow flash update which is
going to be implemented in follow-up patches, introduce a possibility
for a line card to expose relation to nested devlink entity. The nested
devlink entity represents the line card.

Example:

$ devlink lc show pci/0000:01:00.0 lc 1
pci/0000:01:00.0:
  lc 1 state active type 16x100G nested_devlink auxiliary/mlxsw_core.lc.0
    supported_types:
       16x100G
$ devlink dev show auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Benefit from having devlinks iterator helper
devlinks_xa_for_each_registered_get() and move the net pointer
check inside.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>