Skip to content

L
linux
Switch branch/tag
  1. 18 Sep, 2012 1 commit
  3. 12 Sep, 2012 7 commits
  5. 30 Aug, 2012 5 commits
    • Yi Zou's avatar
      block: rate-limit the error message from failing commands · 37d7b34f
      Yi Zou authored 
      When performing a cable pull test w/ active stress I/O using fio over
a dual port Intel 82599 FCoE CNA, w/ 256LUNs on one port and about 32LUNs
on the other, it is observed that the system becomes not usable due to
scsi-ml being busy printing the error messages for all the failing commands.
I don't believe this problem is specific to FCoE and these commands are
anyway failing due to link being down (DID_NO_CONNECT), just rate-limit
the messages here to solve this issue.

v2->v1: use __ratelimit() as Tomas Henzl mentioned as the proper way for
rate-limit per function. However, in this case, the failed i/o gets to
blk_end_request_err() and then blk_update_request(), which also has to
be rate-limited, as added in the v2 of this patch.

v3-v2: resolved conflict to apply on current 3.6-rc3 upstream tip.
Signed-off-by: default avatarYi Zou <yi.zou@intel.com>
Cc: www.Open-FCoE.org <devel@open-fcoe.org>
Cc: Tomas Henzl <thenzl@redhat.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: default avatarJens Axboe <axboe@kernel.dk>
      37d7b34f
    • Linus Torvalds's avatar
      Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux · 155e36d4
      Linus Torvalds authored 
      Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions
      155e36d4
    • Paul Menzel's avatar
      drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S · 6f33814b
      Paul Menzel authored 
      Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: default avatarPaul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      6f33814b
    • Dave Airlie's avatar
      Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes · c1b51124
      Dave Airlie authored 
      Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
      c1b51124
    • Forest Bond's avatar
      gma500: Consider CRTC initially active. · 4a68a74b
      Forest Bond authored 
      [this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: default avatarForest Bond <forest.bond@rapidrollout.com>
Signed-off-by: default avatarAlan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      4a68a74b
  7. 29 Aug, 2012 18 commits
  9. 28 Aug, 2012 9 commits
    • Stefan Behrens's avatar
      Btrfs: fix that repair code is spuriously executed for transid failures · 256dd1bb
      Stefan Behrens authored 
      If verify_parent_transid() fails for all mirrors, the current code
calls repair_io_failure() anyway which means:
- that the disk block is rewritten without repairing anything and
- that a kernel log message is printed which misleadingly claims
  that a read error was corrected.

This is an example:
parent transid verify failed on 615015833600 wanted 110423 found 110424
parent transid verify failed on 615015833600 wanted 110423 found 110424
btrfs read error corrected: ino 1 off 615015833600 (dev /dev/...)

It is wrong to ignore the results from verify_parent_transid() and to
call repair_eb_io_failure() when the verification of the transids failed.
This commit fixes the issue.
Signed-off-by: default avatarStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: default avatarChris Mason <chris.mason@oracle.com>
      256dd1bb
    • Liu Bo's avatar
      Btrfs: fix ordered extent leak when failing to start a transaction · d280e5be
      Liu Bo authored 
      We cannot just return error before freeing ordered extent and releasing reserved
space when we fail to start a transacion.
Signed-off-by: default avatarLiu Bo <bo.li.liu@oracle.com>
Signed-off-by: default avatarChris Mason <chris.mason@oracle.com>
      d280e5be
    • Liu Bo's avatar
      Btrfs: fix a dio write regression · 24c03fa5
      Liu Bo authored 
      This bug is introduced by commit 3b8bde746f6f9bd36a9f05f5f3b6e334318176a9
(Btrfs: lock extents as we map them in DIO).

In dio write, we should unlock the section which we didn't do IO on in case that
we fall back to buffered write.  But we need to not only unlock the section
but also cleanup reserved space for the section.

This bug was found while running xfstests 133, with this 133 no longer complains.
Signed-off-by: default avatarLiu Bo <bo.li.liu@oracle.com>
Signed-off-by: default avatarChris Mason <chris.mason@oracle.com>
      24c03fa5
    • Josef Bacik's avatar
      Btrfs: fix deadlock with freeze and sync V2 · bd7de2c9
      Josef Bacik authored 
      We can deadlock with freeze right now because we unconditionally start a
transaction in our ->sync_fs() call.  To fix this just check and see if we
have a running transaction to commit.  This saves us from the deadlock
because at this point we'll have the umount sem for the sb so we're safe
from freezes coming in after we've done our check.  With this patch the
freeze xfstests no longer deadlocks.  Thanks,
Signed-off-by: default avatarJosef Bacik <jbacik@fusionio.com>
Signed-off-by: default avatarChris Mason <chris.mason@oracle.com>
      bd7de2c9
    • Stefan Behrens's avatar
      Btrfs: revert checksum error statistic which can cause a BUG() · 5ee0844d
      Stefan Behrens authored 
      Commit 442a4f63 added btrfs device
statistic counters for detected IO and checksum errors to Linux 3.5.
The statistic part that counts checksum errors in
end_bio_extent_readpage() can cause a BUG() in a subfunction:
"kernel BUG at fs/btrfs/volumes.c:3762!"
That part is reverted with the current patch.
However, the counting of checksum errors in the scrub context remains
active, and the counting of detected IO errors (read, write or flush
errors) in all contexts remains active.

Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: default avatarStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: default avatarChris Mason <chris.mason@oracle.com>
      5ee0844d
    • Stefan Behrens's avatar
      Btrfs: remove superblock writing after fatal error · 68ce9682
      Stefan Behrens authored 
      With commit acce952b, btrfs was changed to flag the filesystem with
BTRFS_SUPER_FLAG_ERROR and switch to read-only mode after a fatal
error happened like a write I/O errors of all mirrors.
In such situations, on unmount, the superblock is written in
btrfs_error_commit_super(). This is done with the intention to be able
to evaluate the error flag on the next mount. A warning is printed
in this case during the next mount and the log tree is ignored.

The issue is that it is possible that the superblock points to a root
that was not written (due to write I/O errors).
The result is that the filesystem cannot be mounted. btrfsck also does
not start and all the other btrfs-progs tools fail to start as well.
However, mount -o recovery is working well and does the right things
to recover the filesystem (i.e., don't use the log root, clear the
free space cache and use the next mountable root that is stored in the
root backup array).

This patch removes the writing of the superblock when
BTRFS_SUPER_FLAG_ERROR is set, and removes the handling of the error
flag in the mount function.

These lines can be used to reproduce the issue (using /dev/sdm):
SCRATCH_DEV=/dev/sdm
SCRATCH_MNT=/mnt
echo 0 25165824 linear $SCRATCH_DEV 0 | dmsetup create foo
ls -alLF /dev/mapper/foo
mkfs.btrfs /dev/mapper/foo
mount /dev/mapper/foo $SCRATCH_MNT
echo bar > $SCRATCH_MNT/foo
sync
echo 0 25165824 error | dmsetup reload foo
dmsetup resume foo
ls -alF $SCRATCH_MNT
touch $SCRATCH_MNT/1
ls -alF $SCRATCH_MNT
sleep 35
echo 0 25165824 linear $SCRATCH_DEV 0 | dmsetup reload foo
dmsetup resume foo
sleep 1
umount $SCRATCH_MNT
btrfsck /dev/mapper/foo
dmsetup remove foo
Signed-off-by: default avatarStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: default avatarJan Schmidt <list.btrfs@jan-o-sch.net>
      68ce9682
    • Josef Bacik's avatar
      Btrfs: allow delayed refs to be merged · ae1e206b
      Josef Bacik authored 
      Daniel Blueman reported a bug with fio+balance on a ramdisk setup.
Basically what happens is the balance relocates a tree block which will drop
the implicit refs for all of its children and adds a full backref.  Once the
block is relocated we have to add the implicit refs back, so when we cow the
block again we add the implicit refs for its children back.  The problem
comes when the original drop ref doesn't get run before we add the implicit
refs back.  The delayed ref stuff will specifically prefer ADD operations
over DROP to keep us from freeing up an extent that will have references to
it, so we try to add the implicit ref before it is actually removed and we
panic.  This worked fine before because the add would have just canceled the
drop out and we would have been fine.  But the backref walking work needs to
be able to freeze the delayed ref stuff in time so we have this ever
increasing sequence number that gets attached to all new delayed ref updates
which makes us not merge refs and we run into this issue.

So to fix this we need to merge delayed refs.  So everytime we run a
clustered ref we need to try and merge all of its delayed refs.  The backref
walking stuff locks the delayed ref head before processing, so if we have it
locked we are safe to merge any refs inside of the sequence number.  If
there is no sequence number we can merge all refs.  Doing this not only
fixes our bug but keeps the delayed ref code from adding and removing
useless refs and batching together multiple refs into one search instead of
one search per delayed ref, which will really help our commit times.  I ran
this with Daniels test and 276 and I haven't seen any problems.  Thanks,
Reported-by: default avatarDaniel J Blueman <daniel@quora.org>
Signed-off-by: default avatarJosef Bacik <jbacik@fusionio.com>
      ae1e206b
    • Josef Bacik's avatar
      Btrfs: fix enospc problems when deleting a subvol · 5a24e84c
      Josef Bacik authored 
      Subvol delete is a special kind of awful where we use the global reserve to
cover the ENOSPC requirements.  The problem is once we're done removing
everything we do a btrfs_update_inode(), which by default will try to do the
delayed update stuff which will use it's own reserve.  There will be no
space in this reserve and we'll return ENOSPC.  So instead use
btrfs_update_inode_fallback() which will just fallback to updating the inode
item in the case of enospc.  This is fine because the global reserve covers
the space requirements for this.  With this patch I can now delete a subvol
on a problem image Dave Sterba sent me.  Thanks,
Reported-by: default avatarDavid Sterba <dave@jikos.cz>
Signed-off-by: default avatarJosef Bacik <jbacik@fusionio.com>
Signed-off-by: default avatarChris Mason <chris.mason@fusionio.com>
      5a24e84c
    • Miao Xie's avatar
      Btrfs: fix wrong mtime and ctime when creating snapshots · c0f62ded
      Miao Xie authored 
      When we created a new snapshot, the mtime and ctime of its parent directory
were not updated. Fix it.
Signed-off-by: default avatarMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: default avatarChris Mason <chris.mason@fusionio.com>
      c0f62ded
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7