Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Correct the documentation for devm_devfreq_remove_device() argument.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

This patch adds posibility to choose what type of data should be counted
by the PPMU counter. Now the type comes from DT where the event has been
defined. When there is no 'event-data-type' the default value is used,
which is 'read+write data in bytes'.
It is needed when you want to know not only read+write data bytes but
i.e. only write data in byte, or number of read requests, etc.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[Updated property by MyungJoo. data_type --> event_type]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The patch changes the way how the 'ops' gets populated for different
device versions. The matching function now uses 'of_device_id' in order
to identify the device type.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Compile-testing the new driver on platforms without CONFIG_COMMON_CLK
leads to a link error:

drivers/devfreq/tegra20-devfreq.o: In function `tegra_devfreq_target':
tegra20-devfreq.c:(.text+0x288): undefined reference to `clk_set_min_rate'

Add a dependency on COMMON_CLK to avoid this.

Fixes: 1d39ee8dad6d ("PM / devfreq: Introduce driver for NVIDIA Tegra20")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Define new performance events supported by Exynos5422 SoC counters.
The counters are built-in in Dynamic Memory Controller and provide
information regarding memory utilization.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.

When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.

Fix this by returning -EINVAL if request_module returns a positive
value.

Fixes: b53b0128 ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Reorder 'i' and 'v' in "drvier".
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Add missing 'r' in "monitoing".
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Add devfreq driver for NVIDIA Tegra20 SoC's. The driver periodically
reads out Memory Controller counters and adjusts memory frequency based
on the memory clients activity.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[Removed MAINTAINERS updates by MyungJoo so that it can be sent elsewhere.]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

In order to reflect that driver serves NVIDIA Tegra30 and later SoC
generations, let's rename the driver's source file to "tegra30-devfreq.c".
This will make driver files to look more consistent after addition of a
driver for Tegra20.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The driver's compilation doesn't have any specific dependencies, hence
the COMPILE_TEST option can be supported in Kconfig.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The devfreq driver can be used on Tegra30 without any code change and
it works perfectly fine, the default Tegra124 parameters are good enough
for Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
[Modified by MyungJoo to depends on Tegra30/114/124/210 only]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Move hardware configuration to governor's start/resume methods.
This allows to re-initialize hardware counters and reconfigure
cleanly if governor was stopped/paused. That is needed because we
are not aware of all hardware changes that happened while governor
was stopped and the paused state may get out of sync with reality,
hence it's better to start with a clean slate after the pause. In
a result there is no memory bandwidth starvation after resume from
suspend-to-ram that results in display controller underflowing that
happens on resume because of improper decision made by devfreq about
the required memory frequency. This change also cleans up code a tad
by moving hardware-configuration code into a single location.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

There is no need to register the ACTMON's governor separately from
the driver, hence let's move the registration into the driver's probe
function for consistency and to make code cleaner a tad.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The ACTMON's governor supports only the Tegra's devfreq device and there
is no need to use any other governor, hence let's mark Tegra governor as
immutable to permanently stick it with Tegra's devfreq device.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The frequency value potentially could change in-between. It doesn't
cause any real problem at all right now, but that could change in the
future. Hence let's avoid the inconsistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Reset hardware, disable ACTMON clock, release OPP's and handle all
possible error cases correctly, maintaining the correct tear down
order. Also use devm_platform_ioremap_resource() which is now available
in the kernel.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

There is no guarantee that interrupt handling isn't running in parallel
with tegra_actmon_disable_interrupts(), hence it is necessary to protect
DEV_CTRL register accesses and clear IRQ status with ACTMON's IRQ being
disabled in the Interrupt Controller in order to ensure that device
interrupt is indeed being disabled.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

There is no real need in the primary interrupt handler, hence move
everything to the secondary (threaded) handler. In a result locking
is consistent now and there are no potential races with the interrupt
handler because it is protected with the devfreq's mutex.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

There is no real benefit from doing so, hence let's drop that rate setting
for consistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The clk_set_min_rate() could fail and in this case clk_set_rate() sets
rate to 0, which may drop EMC rate to minimum and make machine very
difficult to use.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The write memory barrier isn't needed because the BUS buffer is flushed
by read after write that happens after the removed wmb(), we will also
use readl() instead of the relaxed version to ensure that read is indeed
completed.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

There is no need to insert memory barrier on each readl/writel
invocation, hence use the relaxed versions.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

The kHz to Hz is incorrectly converted in a few places in the code,
this results in a wrong frequency being calculated because devfreq core
uses OPP frequencies that are given in Hz to clamp the rate, while
tegra-devfreq gives to the core value in kHz and then it also expects to
receive value in kHz from the core. In a result memory freq is always set
to a value which is close to ULONG_MAX because of the bug. Hence the EMC
frequency is always capped to the maximum and the driver doesn't do
anything useful. This patch was tested on Tegra30 and Tegra124 SoC's, EMC
frequency scaling works properly now.

Cc: <stable@vger.kernel.org> # 4.14+
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>

Pull MTD fix from Richard Weinberger:
 "A single fix for MTD to correctly set the spi-nor WP pin"

* tag 'fixes-for-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: spi-nor: Fix the disabling of write protection at init

Pull btrfs fixes from David Sterba:
 "Two fixes that popped up during testing:

   - fix for sysfs-related code that adds/removes block groups, warnings
     appear during several fstests in connection with sysfs updates in
     5.3, the fix essentially replaces a workaround with scope NOFS and
     applies to 5.2-based branch too

   - add sanity check of trim range"

* tag 'for-5.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: trim: Check the range passed into to prevent overflow
  Btrfs: fix sysfs warning and missing raid sysfs directories

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for x86:

   - Fix the inconsistent error handling in the umwait init code

   - Rework the boot param zeroing so gcc9 stops complaining about out
     of bound memset. The resulting source code is actually more sane to
     read than the smart solution we had

   - Maintainers update so Tony gets involved when Intel models are
     added

   - Some more fallthrough fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Save fields explicitly, zero out everything else
  MAINTAINERS, x86/CPU: Tony Luck will maintain asm/intel-family.h
  x86/fpu/math-emu: Address fallthrough warnings
  x86/apic/32: Fix yet another implicit fallthrough warning
  x86/umwait: Fix error handling in umwait_init()

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI mixed mode regression caused by recent rework
  which did not take the firmware bitwidth into account"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi-stub: Fix get_efi_config_table on mixed-mode setups

Pull SPDX fixes from Greg KH:
 "Here are four small SPDX fixes for 5.3-rc5.

  A few style fixes for some SPDX comments, added an SPDX tag for one
  file, and fix up some GPL boilerplate for another file.

  All of these have been in linux-next for a few weeks with no reported
  issues (they are comment changes only, so that's to be expected...)"

* tag 'spdx-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
  i2c: stm32: Use the correct style for SPDX License Identifier
  intel_th: Use the correct style for SPDX License Identifier
  coccinelle: api/atomic_as_refcounter: add SPDX License Identifier
  kernel/configs: Replace GPL boilerplate code with SPDX identifier

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.3-rc5.

  These are two different subsystems needing some fixes, the habanalabs
  driver which is has some more big endian fixes for problems found. The
  other are some small soundwire fixes, including some Kconfig
  dependencies needed to resolve reported build errors.

  All of these have been in linux-next this week with no reported
  issues"

* tag 'char-misc-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  misc: xilinx-sdfec: fix dependency and build error
  habanalabs: fix device IRQ unmasking for BE host
  habanalabs: fix endianness handling for internal QMAN submission
  habanalabs: fix completion queue handling when host is BE
  habanalabs: fix endianness handling for packets from user
  habanalabs: fix DRAM usage accounting on context tear down
  habanalabs: Avoid double free in error flow
  soundwire: fix regmap dependencies and align with other serial links
  soundwire: cadence_master: fix definitions for INTSTAT0/1
  soundwire: cadence_master: fix register definition for SLAVE_STATE

Pull staging/IIO fixes from Greg KH:
 "Here are four small staging and iio driver fixes for 5.3-rc5

  Two are for the dt3000 comedi driver for some reported problems found
  in that codebase, and two are some small iio fixes.

  All of these have been in linux-next this week with no reported
  issues"

* tag 'staging-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: dt3000: Fix rounding up of timer divisor
  staging: comedi: dt3000: Fix signed integer overflow 'divider * base'
  iio: adc: max9611: Fix temperature reading in probe
  iio: frequency: adf4371: Fix output frequency setting

Pull USB fixes from Greg KH:
 "Here are number of small USB fixes for 5.3-rc5.

  Syzbot has been on a tear recently now that it has some good USB
  debugging hooks integrated, so there's a number of fixes in here found
  by those tools for some _very_ old bugs. Also a handful of gadget
  driver fixes for reported issues, some hopefully-final dma fixes for
  host controller drivers, and some new USB serial gadget driver ids.

  All of these have been in linux-next this week with no reported issues
  (the usb-serial ones were in linux-next in its own branch, but merged
  into mine on Friday)"

* tag 'usb-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: add a hcd_uses_dma helper
  usb: don't create dma pools for HCDs with a localmem_pool
  usb: chipidea: imx: fix EPROBE_DEFER support during driver probe
  usb: host: fotg2: restart hcd after port reset
  USB: CDC: fix sanity checks in CDC union parser
  usb: cdc-acm: make sure a refcount is taken early enough
  USB: serial: option: add the BroadMobi BM818 card
  USB: serial: option: Add Motorola modem UARTs
  USB: core: Fix races in character device registration and deregistraion
  usb: gadget: mass_storage: Fix races between fsg_disable and fsg_set_alt
  usb: gadget: composite: Clear "suspended" on reset/disconnect
  usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"
  USB: serial: option: add D-Link DWM-222 device ID
  USB: serial: option: Add support for ZTE MF871A

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into this series. This contains:

   - Revert of the REQ_NOWAIT_INLINE and associated dio changes. There
     were still corner cases there, and even though I had a solution for
     it, it's too involved for this stage. (me)

   - Set of NVMe fixes (via Sagi)

   - io_uring fix for fixed buffers (Anthony)

   - io_uring defer issue fix (Jackie)

   - Regression fix for queue sync at exit time (zhengbin)

   - xen blk-back memory leak fix (Wenwen)"

* tag 'for-linus-2019-08-17' of git://git.kernel.dk/linux-block:
  io_uring: fix an issue when IOSQE_IO_LINK is inserted into defer list
  block: remove REQ_NOWAIT_INLINE
  io_uring: fix manual setup of iov_iter for fixed buffers
  xen/blkback: fix memory leaks
  blk-mq: move cancel of requeue_work to the front of blk_exit_queue
  nvme-pci: Fix async probe remove race
  nvme: fix controller removal race with scan work
  nvme-rdma: fix possible use-after-free in connect error flow
  nvme: fix a possible deadlock when passthru commands sent to a multipath device
  nvme-core: Fix extra device_put() call on error path
  nvmet-file: fix nvmet_file_flush() always returning an error
  nvmet-loop: Flush nvme_delete_wq when removing the port
  nvmet: Fix use-after-free bug when a port is removed
  nvme-multipath: revalidate nvme_ns_head gendisk in nvme_validate_ns

Pull Hyper-V fixes from Sasha Levin:

 - A few fixes for the userspace hyper-v tools from Adrian Vladu.

 - A fix for the hyper-v MAINTAINERs entry from Lan Tianyu.

 - Fix for SPDX license identifier in the userspace tools from Nishad
   Kamdar.

* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  MAINTAINERS: Fix Hyperv vIOMMU driver file name
  tools: hv: Use the correct style for SPDX License Identifier
  tools: hv: fix typos in toolchain
  tools: hv: fix KVP and VSS daemons exit code
  tools: hv: fixed Python pep8/flake8 warnings for lsvmbus

The Hyperv vIOMMU file name should be "hyperv-iommu.c" rather
than "hyperv_iommu.c". This patch is to fix it.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

This patch corrects the SPDX License Identifier style
in the trace header file related to Microsoft Hyper-V
client drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Fix typos in the HyperV toolchain.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>

Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HyperV KVP and VSS daemons should exit with 0 when the '--help'
or '-h' flags are used.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>

Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>