- 15 Nov, 2012 4 commits
-
-
Vikram Narayanan authored
Make the error messages more debugging friendly Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Shmulik Ladkani authored
Simply 'parse_cmdline_partitions': the outer loop iterating over 'partitions' is actually a search loop, it does not execute the inner loop for each partition, only for the matched partition. Let's break when search is successful, and move all inner code (relevant only for the matched partition) outside of the outer loop. Resulting code is much more readable, and makes the indent level sane. Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Brian Norris authored
This patch fixes errors seen in identifying old Samsung SLC, due to the following commits: commit e2d3a35e mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID commit e3b88bd6 mtd: nand: add generic READ ID length calculation functions Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with wraparound like: Samsung K9K8G08U0D ec d3 51 95 58 ec ec d3 Samsung K9F1G08U0C ec f1 00 95 40 ec ec f1 Samsung K9F2G08U0B ec da 10 95 44 00 ec da This bad wraparound makes it hard to reliably detect the difference between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID. The fix is to, for now, only use the new Samsung table for MLC. We cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID decode information. Note that this applies in addition to the previous regression fix: commit bc86cf7a mtd: nand: fix Samsung SLC NAND identification regression Together, these patches completely restore the previous detection behavior so that we cannot see any more regressions in Samsung SLC NAND (finger crossed). With luck, I can get a hold of a Samsung representative and stop having to cross my fingers eventually. Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Brian Norris authored
A combination of the following two commits caused a regression in 3.7-rc1 when identifying some Samsung NAND, so that some previously working NAND were no longer detected properly: commit e3b88bd6 mtd: nand: add generic READ ID length calculation functions commit e2d3a35e mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID Particularly, a regression was seen on Samsung K9F2G08U0B, with the following full 8-byte READ ID string: ec da 10 95 44 00 ec da The basic problem is that Samsung manufactures both SLC and MLC NAND that use a non-standard decoding table for deriving information from their IDs. I have heuristically determined that all the chips that use the new table have ID strings which wrap around after the 6th byte. Unfortunately, I overlooked the fact that some older Samsung SLC (which use a different decoding table) have "5 byte ID strings" which also wrap around after the 6th byte. This patch re-introduces a distinction between these old and new Samsung NAND by checking that the 6th byte is non-zero, allowing both old and new Samsung NAND to be detected properly. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Brian Norris <computersforpeace@gmail.com> Reported-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
- 09 Nov, 2012 3 commits
-
-
Thomas Betker authored
jffs2_write_begin() first acquires the page lock, then f->sem. This causes an AB-BA deadlock with jffs2_garbage_collect_live(), which first acquires f->sem, then the page lock: jffs2_garbage_collect_live mutex_lock(&f->sem) (A) jffs2_garbage_collect_dnode jffs2_gc_fetch_page read_cache_page_async do_read_cache_page lock_page(page) (B) jffs2_write_begin grab_cache_page_write_begin find_lock_page lock_page(page) (B) mutex_lock(&f->sem) (A) We fix this by restructuring jffs2_write_begin() to take f->sem before the page lock. However, we make sure that f->sem is not held when calling jffs2_reserve_space(), as this is not permitted by the locking rules. The deadlock above was observed multiple times on an SoC with a dual ARMv7 (Cortex-A9), running the long-term 3.4.11 kernel; it occurred when using scp to copy files from a host system to the ARM target system. The fix was heavily tested on the same target system. Cc: stable@vger.kernel.org Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Sachin Kamat authored
Fixes the following sparse warning: drivers/mtd/onenand/onenand_base.c:3697:5: warning: symbol 'flexonenand_set_boundary' was not declared. Should it be static? Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Jiri Engelthaler authored
Fixed parsing end absolute address. Signed-off-by: Jiri Engelthaler <engycz@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
- 04 Nov, 2012 1 commit
-
-
Linus Torvalds authored
-
- 03 Nov, 2012 15 commits
-
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfixes from Trond Myklebust: - Fix a bunch of deadlock situations: * State recovery can deadlock if we fail to release sequence ids before scheduling the recovery thread. * Calling deactivate_super() from an RPC workqueue thread can deadlock because of the call to rpc_shutdown_client. - Display the device name correctly in /proc/*/mounts - Fix a number of incorrect error return values: * When NFSv3 mounts fail due to a timeout. * On NFSv4.1 backchannel setup failure * On NFSv4 open access checks - pnfs_find_alloc_layout() must check the layout pointer for NULL - Fix a regression in the legacy DNS resolved * tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: NFS4: nfs4_opendata_access should return errno NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly SUNRPC: return proper errno from backchannel_rqst NFS: add nfs_sb_deactive_async to avoid deadlock nfs: Show original device name verbatim in /proc/*/mount{s,info} nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts nfs: Check whether a layout pointer is NULL before free it NFS: fix bug in legacy DNS resolver. NFSv4: nfs4_locku_done must release the sequence id NFSv4.1: We must release the sequence id when we fail to get a session slot NFS: Wait for session recovery to finish before returning
-
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linuxLinus Torvalds authored
Pull thermal management & ACPI update from Zhang Rui, Ho humm. Normally these things go through Len. But it's just three small fixes, I guess I can pull directly too. * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: exynos4_tmu_driver_ids should be exynos_tmu_driver_ids. ACPI video: Ignore errors after _DOD evaluation. thermal: solve compilation errors in rcar_thermal
-
git://git.pengutronix.de/git/wsa/linuxLinus Torvalds authored
Pull i2c embedded fixes from Wolfram Sang: "Two patches are usual stuff. The bigger patch is needed to correct a wrong decision made in this merge window. We hoped to get the PIOQUEUE mode in the mxs driver working with DMA, but it turned out to be too broken (leading to data loss), so we now think it is best to remove it entirely and work only with DMA now. The patch should be in 3.7. IMO, so users never get the chance to use both modes in parallel." * 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux: i2c: tegra: set irq name as device name i2c-nomadik: Fixup clock handling i2c: mxs: remove broken PIOQUEUE support
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull drm fixes from Dave Airlie: "Scattered selection of fixes: - radeon: load detect fixes from SuSE/AMD - intel: misc i830, sdvo regression, vesafb kickoff ums fix - exynos: maintainers entry update + fixes - udl: fix stride scanout issue it's slightly bigger than I'd probably like, but nothing looked dangerous enough to hold off on." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/udl: fix stride issues scanning out stride != width*bpp drm/radeon: add load detection support for ext DAC on R200 (v2) DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms(). DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips. DRM/Radeon: Clean up code in TV DAC load detection. drm/radeon: fix ATPX function documentation drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon DRM/Radeon: On DVI-I use Load Detection when EDID is bogus. DRM/Radeon: Fix primary DAC Load Detection for RV100 chips. DRM/Radeon: Fix Load Detection on legacy primary DAC. drm: exynos: removed warning due to missing typecast for mixer driver data drm/exynos: add support for ARCH_MULTIPLATFORM MAINTAINERS: Add git repository for Exynos DRM drm/exynos: fix display on issue drm/i915: Only kick out vesafb if we takeover the fbcon with KMS drm/i915: be less verbose about inability to provide vendor backlight drm/i915: clear the entire sdvo infoframe buffer drm/i915: VGA needs to be on pipe A on i830M drm/i915: fix overlay on i830M
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "First post-Sandy pull request" 1) Fix antenna gain handling and initialization of chan->max_reg_power in wireless, from Felix Fietkau. 2) Fix nexthop handling in H.232 conntrack helper, from Julian Anastasov. 3) Only process 80211 mesh config header in certain kinds of frames, from Javier Cardona. 4) 80211 management frame header length needs to be validated, from Johannes Berg. 5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay. 6) Test for permanent state correctly in VXLAN driver, from Stephen Hemminger. 7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov. 8) Fix off by one errors in bonding, from Nikolay ALeksandrov. 9) Fix divide by zero in TCP-Illinois congestion control. From Jesper Dangaard Brouer. 10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a sizeof of a sizeof, so you can size your size" Fix from Julian Anastasov. 11) Several drivers do mdiobus_free without first doing an mdiobus_unregister leading to stray pointer references. Fix from Peter Senna Tschudin. 12) Fix OOPS in l2tp_eth_create() error path, it's another danling pointer kinda situation. Fix from Tom Parkin. 13) Hardware driven by the vmxnet driver can't handle larger than 16K fragments, so split them up when necessary. From Eric Dumazet. 14) Handle zero length data length in tcp_send_rcvq() properly. Fix from Pavel Emelyanov. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits) tcp-repair: Handle zero-length data put in rcv queue vmxnet3: must split too big fragments l2tp: fix oops in l2tp_eth_create() error path cxgb4: Fix unable to get UP event from the LLD drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free bnx2x: fix HW initialization using fw 7.8.x tcp: Fix double sizeof in new tcp_metrics code net: fix divide by zero in tcp algorithm illinois net: sctp: Fix typo in net/sctp bonding: fix second off-by-one error bonding: fix off-by-one error bnx2x: Disable FCoE for 57840 since not yet supported by FW bnx2x: Fix no link on 577xx 10G-baseT bnx2x: Fix unrecognized SFP+ module after driver is loaded bnx2x: Fix potential incorrect link speed provision bnx2x: Restore global registers back to default. bnx2x: Fix link down in 57712 following LFA bnx2x: Fix 57810 1G-KR link against certain switches. ixgbe: PTP get_ts_info missing software support ...
-
Pavel Emelyanov authored
When sending data into a tcp socket in repair state we should check for the amount of data being 0 explicitly. Otherwise we'll have an skb with seq == end_seq in rcv queue, but tcp doesn't expect this to happen (in particular a warn_on in tcp_recvmsg shoots). Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work as long as we provided PAGE_SIZE fragments. Our stack can now build larger fragments, so we need to split them to the 16kbytes boundary. Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: jongman heo <jongman.heo@samsung.com> Tested-by: jongman heo <jongman.heo@samsung.com> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Reviewed-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tom Parkin authored
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the 32k-interface limit), the netdev is freed in the error path. However, the l2tp_eth_sess structure's dev pointer is left uncleared, and this results in l2tp_eth_delete() then attempting to unregister the same netdev later in the session teardown. This results in an oops. To avoid this, clear the session dev pointer in the error path. Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jonghwan Choi authored
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com> Reviewed-by: Amit Daniel Kachhap <amit.kachhap@linaro.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
-
Igor Murzov authored
There are systems where video module known to work fine regardless of broken _DOD and ignoring returned value here doesn't cause any issues later. This should fix brightness controls on some laptops. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47861Signed-off-by: Igor Murzov <e-mail@date.by> Reviewed-by: Sergey V <sftp.mtuci@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
-
Devendra Naga authored
following were the errors reported drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’: drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default] include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’ drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’ include/linux/thermal.h:166:29: note: declared here make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1 make: *** [drivers/thermal/rcar_thermal.o] Error 2 with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) Signed-off-by: Devendra Naga <develkernel412222@gmail.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
-
Vipul Pandya authored
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory then offload capabilities of the cards were getting disabled during initialization. Hence ULDs do not get an UP event from the LLD. Signed-off-by: Jay Hernandez <jay@chelsio.com> Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Senna Tschudin authored
Based on commit b27393ae Calling mdiobus_free without calling mdiobus_unregister causes BUG_ON(). This patch fixes the issue. The semantic patch that found this issue(http://coccinelle.lip6.fr/): // <smpl> @@ expression E; @@ ... when != mdiobus_unregister(E); + mdiobus_unregister(E); mdiobus_free(E); // </smpl> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Senna Tschudin authored
Based on commit b27393ae Calling mdiobus_free without calling mdiobus_unregister causes BUG_ON(). This patch fixes the issue. The semantic patch that found this issue(http://coccinelle.lip6.fr/): // <smpl> @@ expression E; @@ ... when != mdiobus_unregister(E); + mdiobus_unregister(E); mdiobus_free(E); // </smpl> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Tested-by: Roland Stigge <stigge@antcom.de> Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dmitry Kravkov authored
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be initialized using fw values for all devices. Otherwise ETS on 57712/578xx will not work. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 02 Nov, 2012 17 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management update from Rafael J. Wysocki: "Change the email address of the powernow-k8 maintainer." * tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq / powernow-k8: Change maintainer's email address
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input subsystem fixes from Dmitry Torokhov: "Just a few driver fixes." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: tsc40 - remove wrong announcement of pressure support Input: lpc32xx-keys - select INPUT_MATRIXKMAP Input: pxa27x_keypad - clear pending interrupts on keypad config Input: wacom - correct bad Cintiq 24HD check Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD Input: egalax_ts - get gpio from devicetree
-
Weston Andros Adamson authored
Return errno - not an NFS4ERR_. This worked because NFS4ERR_ACCESS == EACCES. Signed-off-by: Weston Andros Adamson <dros@netapp.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds authored
Pull more scsi target fixes from Nicholas Bellinger: "This series is a second round of target fixes for v3.7-rc4 that have come into target-devel over the last days, and are important enough to be applied ASAP. All are being CC'ed to stable. The most important two are: - target: Re-add explict zeroing of INQUIRY bounce buffer memory to fix a regression for handling zero-length payloads, a bug that went during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo) - iscsi-target: Fix a long-standing missed R2T wakeup race in TX thread processing when using a single queue slot. (Roland) Thanks to Roland & PureStorage team for helping to track down this long standing race with iscsi-target single queue slot operation. Also, the tcm_fc(FCoE) regression bug that was observed recently with -rc2 code has also been resolved with the cancel_delayed_work() return bugfix (commit c0158ca6: "workqueue: cancel_delayed_work() should return %false if work item is idle") now in -rc3. Thanks again to Yi Zou, MDR, Robert Love @ Intel for helping to track this down." * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path iscsi-target: Fix missed wakeup race in TX thread target: Avoid integer overflow in se_dev_align_max_sectors() target: Don't return success from module_init() if setup fails target: Re-add explict zeroing of INQUIRY bounce buffer memory
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-stagingLinus Torvalds authored
Pull hwmon fixes from Guenter Roeck: "An e-mail address update, and fix a compile error on SPARC" * tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: Only include of_match_table with CONFIG_OF_GPIO hwmon, fam15h_power: Change email address, MAINTAINERS entry
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frvLinus Torvalds authored
Pull FRV fixes from David Howells: "A collection of small fixes for the FRV architecture." * tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv: frv: fix the broken preempt frv: switch to saner kernel_execve() semantics FRV: Fix the new-style kernel_thread() stuff FRV: Fix the preemption handling FRV: gcc-4.1.2 also inlines weak functions FRV: Don't objcopy the GNU build_id note FRV: Add missing linux/export.h #inclusions
-
Linus Torvalds authored
Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen bugfixes from Konrad Rzeszutek Wilk: - Use appropriate macros instead of hand-rolling our own (ARM). - Fixes if FB/KBD closed unexpectedly. - Fix memory leak in /dev/gntdev ioctl calls. - Fix overflow check in xenbus_file_write. - Document cleanup. - Performance optimization when migrating guests. * tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/mmu: Use Xen specific TLB flush instead of the generic one. xen/arm: use the __HVC macro xen/xenbus: fix overflow check in xenbus_file_write() xen-kbdfront: handle backend CLOSED without CLOSING xen-fbfront: handle backend CLOSED without CLOSING xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF x86: remove obsolete comment from asm/xen/hypervisor.h
-
Sasha Levin authored
This hashtable implementation is using hlist buckets to provide a simple hashtable to prevent it from getting reimplemented all over the kernel. Signed-off-by: Sasha Levin <levinsasha928@gmail.com> [ Merging this now, so that subsystems can start applying Sasha's patches that use this - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Al Viro authored
Just get %icc2 into the state we would have after local_irq_disable() and physical IRQ having happened since then. Then we can simply use preempt_schedule_irq() and be done with the whole mess. Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
The kernel_thread() changes for FRV don't work, and FRV fails to boot, starting with: commit 02ce496f Author: Al Viro <viro@zeniv.linux.org.uk> Date: Tue Sep 18 22:18:51 2012 -0400 Subject: frv: split ret_from_fork, simplify kernel_thread() a lot The problem is that the userspace registers are completely cleared when a kernel thread is created and all subsequent user threads are then copied from that. Unfortunately, however, the TBR and PSR registers are restored from the pt_regs and the values they should be set to are clobbered by the memset. Instead, copy across the old user registers as normal, and then merely alter GR8 and GR9 in it if we're going to execute a kernel thread. Signed-off-by: David Howells <dhowells@redhat.com>
-
David Howells authored
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is incorrectly loaded into the threadinfo flags rather than the threadinfo preemption count. Unfortunately, the code cannot be simply converted to use preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to cut down on the cost of actually disabling interrupts and thus local_irq_enable() doesn't actually enable interrupts. Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> cc: Al Viro <viro@ZenIV.linux.org.uk>
-
David Howells authored
gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy thread_info_cache_init() gets inlined into start_kernel(). Signed-off-by: David Howells <dhowells@redhat.com>
-
David Howells authored
Don't let objcopy transfer the GNU build_id note into the loadable image as it is located at address 0 and the image ends up >3G in size. Signed-off-by: David Howells <dhowells@redhat.com>
-
David Howells authored
Add missing linux/export.h #inclusions to the FRV arch. Signed-off-by: David Howells <dhowells@redhat.com>
-
Laxman Dewangan authored
When watching the irqs name of tegra i2c, all instances irq name shows as tegra_i2c. Passing the device name properly to have the irq names with instance like tegra-i2c.0, tegra-i2c.1 etc. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-
Philippe Begnic authored
Make sure to clk_prepare as well as clk_enable. Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-