- 20 Nov, 2021 21 commits
-
-
Konrad Dybcio authored
Disable PON/RESIN keys by default and keep the RESIN keycode set-per-board, as these settings are not common between devices (one cannot even assume all devices have buttons nowadays..). Signed-off-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20211114012755.112226-7-konrad.dybcio@somainline.org
-
Konrad Dybcio authored
Thermal zone names should not be longer than 20 names, which is indicated by a message at boot. Change "camera-thermal-bottom" to "cam-thermal-bottom" to fix it. Signed-off-by:
-
Konrad Dybcio authored
Using interrupts = <&pdc X Y> makes the interrupt framework interpret this as the &pdc-nth range of the main interrupt controller (GIC). Fix it. Signed-off-by:
-
Konrad Dybcio authored
Arch timer runs at 19.2 MHz. Specify the rate in the timer node. Signed-off-by:
-
Konrad Dybcio authored
The redistributor properties were missing. Add them. Signed-off-by:
-
Konrad Dybcio authored
Add the missing third QUPv3 master node. Signed-off-by:
-
Konrad Dybcio authored
Almost any board that boots and has a way to interact with it (say for the rare cases of just-pstore or let's-rely-on-bootloader-setup) needs to set some GPIOs, so it makes no sense to include gpio.h separately each time. Hence move it to SoC DTSI. Signed-off-by:
-
Shawn Guo authored
QUSB2 PHY requires vdd-supply for digital circuit operation. Add it for platforms that miss it. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Acked-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Yassine Oudjana authored
This platform actually doesn't have TUSB320, but rather TUSB320L. The TUSB320 compatible string was used due to lack of support for TUSB320L, and it was close enough to detect cable plug-in and direction, but it was limited to upstream facing port mode only. Now that support for TUSB320L is added[1], change node name and compatible to match and allow it to be properly reset and have its mode set to dual-role port. [1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=ce0320bd3872038569be360870e2d5251b975692Signed-off-by:
Yassine Oudjana <y.oudjana@protonmail.com> Signed-off-by:
-
Yassine Oudjana authored
Add a node and pin states for Cypress StreetFighter touchkey controller. Signed-off-by:
-
Dmitry Baryshkov authored
Device tree for the Sony Xperia tone family of devices specifies S9+S10+S11 SAW regulator as a part of the pmi8994_spmi_regulators device tree node. However PMI8994 does not have these regulators, they are part of the PM8994 device. All other MSM8996-based devices list them in the pm8994_spmi_regulators device tree node. Move them accordingly. Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
The qcom_rpm_smd_regulator driver uses vdd_lvs1_2-supply property to specify the supply regulator for LVS1 and LVS2 (following the pin name in the PMIC datasheet). Correct the board's device tree property, so that the regulator supply is setup properly. Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Dmitry Baryshkov authored
The qcom_rpm_smd_regulator driver uses vdd_lvs1_2-supply property to specify the supply regulator for LVS1 and LVS2 (following the pin name in the PMIC datasheet). Correct the board's device tree property, so that the regulator supply is setup properly. Signed-off-by:
-
Dmitry Baryshkov authored
Specify that S11 (well, whole block of s8+s9+s10+s11) of pm8994 and S2 (s2 + s3) of pmi8994 are supplied by vph_pwr. While we are at it, add regulator name to S11, so that is displayed as VDD_APCC in the system. Signed-off-by:
-
Dmitry Baryshkov authored
Specify firmware name to be used for the ADSP. Quoting Bjorn from the respective apq8016-sbc commit: The firmware for the modem and WiFi subsystems platform specific and is signed with a OEM specific key (or a test key). In order to support more than a single device it is therefor not possible to rely on the default path and stash these files directly in the firmware directory. Signed-off-by:
-
Konrad Dybcio authored
Add support for SONY Xperia XZ2, XZ2 Compact and XZ3 smartphones, all based on the Qualcomm SDM845 chipset. There also exists a fourth Tama device, the XZ2 Premium (Aurora) with a 4K display, but it's relatively rare. The devices are affected by a scary UFS behaviour where sending a certain UFS command (which is worked around on downstream) renders the device unbootable, by effectively erasing the bootloader. Therefore UFS AND UFSPHY are strictly disabled for now. Downstream workaround: https://github.com/kholk/kernel/commit/2e7a9ee1c91a016baa0b826a7752ec45663a0561 This platform's bootloader is not very nice either. To boot mainline you need to flash a bogus DTBO (fastboot erasing may cut it, but it takes an inhumane amount of time) - one that's just 4 bytes (all zeroes) seems to work just fine. Of course, one can also provide a "normal" DTBO (device-specific DT overlayed on top of the SoC DT), but that's not yet supported by the mainline kernel build system. Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by:
Martin Botka <martin.botka@somainline.org> Signed-off-by:
-
David Heidelberg authored
These properties aren't documented nor implemented in the driver. Drop them. Fixes warnings as: $ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/msm/gpu.yaml ... arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml: gpu@b00000: 'qcom,gpu-quirk-fault-detect-mask', 'qcom,gpu-quirk-two-pass-use-wfi' do not match any of the regexes: 'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/display/msm/gpu.yaml ... Fixes: 69cc3114 ("arm64: dts: Add Adreno GPU definitions") Signed-off-by:
David Heidelberg <david@ixit.cz> Signed-off-by:
-
Philip Chen authored
Support Homestar rev4 board where Parade ps8640 is added as the second source edp bridge. Support different edp bridge chips in different board revisions, now we move the #incldue line of the edp bridge dts fragment (e.g. sc7180-trogdor-ti-sn65dsi86.dtsi) from "sc7180-trogdor-homestar.dtsi" to per-board-rev dts files. Since the edp bridge dts fragment overrides 'dsi0_out', which is defined in "sc7180.dtsi", move the #incldue line of "sc7180.dtsi" from "sc7180-trogdor-homestar.dtsi" to per-board-rev dts files too, before the #include line of the edp bridge dts fragment. Signed-off-by:
Philip Chen <philipchen@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Philip Chen authored
Support Lazor/Limozeen rev9 board where Parade ps8640 is added as the second source edp bridge. To support different edp bridge chips in different board revisions, now we move the #incldue line of the edp bridge dts fragment (e.g. sc7180-trogdor-ti-sn65dsi86.dtsi) from "sc7180-trogdor-lazor.dtsi" to per-board-rev dts files. Since the edp bridge dts fragment overrides 'dsi0_out', which is defined in "sc7180.dtsi", move the #incldue line of "sc7180.dtsi" from "sc7180-trogdor-lazor.dtsi" to per-board-rev dts files too, before the #include line of the edp bridge dts fragment. Signed-off-by:
-
Philip Chen authored
MSM DSI host driver actually parses "data-lanes" in DT and compare it with the number of DSI lanes the bridge driver sets for mipi_dsi_device. So we need to always specify "data-lanes" for the DSI host output. As of now, "data-lanes" is added to ti-sn65dsi86 dts fragment, but missing in parade-ps8640 dts fragment, which requires a fixup. Since we'll do 4-lane DSI regardless of which bridge chip is used, instead of adding "data-lanes" to parade-ps8640 dts fragment, let's just move "data-lanes" from the bridge dts to sc7180-trogdor.dtsi. Signed-off-by:
-
Philip Chen authored
The edp bridge dts fragment files use the macros defined in 'dt-bindings/gpio/gpio.h'. To help us more flexibly order the #include lines of dts files in a board-revision-specific dts file, let's include the gpio header in the bridge dts fragment files themselves. Signed-off-by:
-
- 18 Nov, 2021 9 commits
-
-
Robert Marko authored
IPQ8074 uses an IPQ4019 compatible MDIO controller that is already supported in the kernel, so add the DT node in order to use it. Signed-off-by:
Robert Marko <robimarko@gmail.com> Signed-off-by:
-
Kate Doeen authored
Enable loading the Qualcomm Venus video accelerator firmware on Xiaomi Pocophone F1. Signed-off-by:
Kate Doeen <jld3103yt@gmail.com> Signed-off-by:
-
Kate Doeen authored
Enable loading the Qualcomm Venus video accelerator firmware on OnePlus sdm845 devices. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Signed-off-by:
-
Dikshita Agarwal authored
Add DT entries for the sc7280 venus encoder/decoder. Co-developed-by:
Mansur Alisha Shaik <mansur@codeaurora.org> Signed-off-by:
Dikshita Agarwal <dikshita@codeaurora.org> Signed-off-by:
-
Stephan Gerhold authored
Add the "chassis-type" to msm8916-samsung-serranove and sm7225-fairphone-fp4 that were posted before the patch that added the chassis-type to existing device trees, but merged after it. Also, looks like sdm636-sony-xperia-ganges-mermaid was missing in commit eaa744b1 ("arm64: dts: qcom: add 'chassis-type' property") so add it there as well. Cc: Luca Weiss <luca@z3ntu.xyz> Cc: Arnaud Ferraris <arnaud.ferraris@collabora.com> Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Reviewed-by:
Arnaud Ferraris <arnaud.ferraris@collabora.com> Signed-off-by:
-
Srinivas Kandagatla authored
This patch adds sound card support for MTP using WCD938x headset playback, capture, WSA8810 Speaker Playback and DMICs via VA macro. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
-
Srinivas Kandagatla authored
SM8250-MTP has WSA8810 via wsa macro for Speaker playback use case. Add node for this device to be able to use it for sound card device. Signed-off-by:
-
Srinivas Kandagatla authored
SM8250-MTP has WCD9380 codec for headset playback and capture via rx and tx macro respectively. Add node for this device to be able to use it for sound card device. Signed-off-by:
-
Srinivas Kandagatla authored
SM8250 has TX and RX macros with SoundWire Controllers to attach with codecs like WCD938x. Add these nodes for sm8250 mtp audio use case. Signed-off-by:
-
- 14 Nov, 2021 10 commits
-
-
Linus Torvalds authored
-
Gustavo A. R. Silva authored
Add Kconfig support for -Wimplicit-fallthrough for both GCC and Clang. The compiler option is under configuration CC_IMPLICIT_FALLTHROUGH, which is enabled by default. Special thanks to Nathan Chancellor who fixed the Clang bug[1][2]. This bugfix only appears in Clang 14.0.0, so older versions still contain the bug and -Wimplicit-fallthrough won't be enabled for them, for now. This concludes a long journey and now we are finally getting rid of the unintentional fallthrough bug-class in the kernel, entirely. :) Link: https://github.com/llvm/llvm-project/commit/9ed4a94d6451046a51ef393cd62f00710820a7e8 [1] Link: https://bugs.llvm.org/show_bug.cgi?id=51094 [2] Link: https://github.com/KSPP/linux/issues/115 Link: https://github.com/ClangBuiltLinux/linux/issues/236Co-developed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Nathan Chancellor <nathan@kernel.org> Tested-by:
-
git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds authored
Pull xfs cleanups from Darrick Wong: "The most 'exciting' aspect of this branch is that the xfsprogs maintainer and I have worked through the last of the code discrepancies between kernel and userspace libxfs such that there are no code differences between the two except for #includes. IOWs, diff suffices to demonstrate that the userspace tools behave the same as the kernel, and kernel-only bits are clearly marked in the /kernel/ source code instead of just the userspace source. Summary: - Clean up open-coded swap() calls. - A little bit of #ifdef golf to complete the reunification of the kernel and userspace libxfs source code" * tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: sync xfs_btree_split macros with userspace libxfs xfs: #ifdef out perag code for userspace xfs: use swap() to make dabtree code cleaner -
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linuxLinus Torvalds authored
Pull more parisc fixes from Helge Deller: "Fix a build error in stracktrace.c, fix resolving of addresses to function names in backtraces, fix single-stepping in assembly code and flush userspace pte's when using set_pte_at()" * tag 'for-5.16/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc/entry: fix trace test in syscall exit path parisc: Flush kernel data mapping in set_pte_at() when installing pte for user page parisc: Fix implicit declaration of function '__kernel_text_address' parisc: Fix backtrace to always include init funtion names
-
git://git.libc.org/linux-shLinus Torvalds authored
Pull arch/sh updates from Rich Felker. * tag 'sh-for-5.16' of git://git.libc.org/linux-sh: sh: pgtable-3level: Fix cast to pointer from integer of different size sh: fix READ/WRITE redefinition warnings sh: define __BIG_ENDIAN for math-emu sh: math-emu: drop unused functions sh: fix kconfig unmet dependency warning for FRAME_POINTER sh: Cleanup about SPARSE_IRQ sh: kdump: add some attribute to function maple: fix wrong return value of maple_bus_init(). sh: boot: avoid unneeded rebuilds under arch/sh/boot/compressed/ sh: boot: add intermediate vmlinux.bin* to targets instead of extra-y sh: boards: Fix the cacography in irq.c sh: check return code of request_irq sh: fix trivial misannotations
-
git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fixes from Russell King: - Fix early_iounmap - Drop cc-option fallbacks for architecture selection * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9156/1: drop cc-option fallbacks for architecture selection ARM: 9155/1: fix early early_iounmap()
-
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linuxLinus Torvalds authored
Pull devicetree fixes from Rob Herring: - Two fixes due to DT node name changes on Arm, Ltd. boards - Treewide rename of Ingenic CGU headers - Update ST email addresses - Remove Netlogic DT bindings - Dropping few more cases of redundant 'maxItems' in schemas - Convert toshiba,tc358767 bridge binding to schema * tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: dt-bindings: watchdog: sunxi: fix error in schema bindings: media: venus: Drop redundant maxItems for power-domain-names dt-bindings: Remove Netlogic bindings clk: versatile: clk-icst: Ensure clock names are unique of: Support using 'mask' in making device bus id dt-bindings: treewide: Update @st.com email address to @foss.st.com dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml dt-bindings: media: Update maintainers for st,stm32-cec.yaml dt-bindings: mfd: timers: Update maintainers for st,stm32-timers dt-bindings: timer: Update maintainers for st,stm32-timer dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fix from Thomas Gleixner: "A single fix for POSIX CPU timers to address a problem where POSIX CPU timer delivery stops working for a new child task because copy_process() copies state information which is only valid for the parent task" * tag 'timers-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: posix-cpu-timers: Clear task::posix_cputimers_work in copy_process()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "A set of fixes for the interrupt subsystem Core code: - A regression fix for the Open Firmware interrupt mapping code where a interrupt controller property in a node caused a map property in the same node to be ignored. Interrupt chip drivers: - Workaround a limitation in SiFive PLIC interrupt chip which silently ignores an EOI when the interrupt line is masked. - Provide the missing mask/unmask implementation for the CSKY MP interrupt controller. PCI/MSI: - Prevent a use after free when PCI/MSI interrupts are released by destroying the sysfs entries before freeing the memory which is accessed in the sysfs show() function. - Implement a mask quirk for the Nvidia ION AHCI chip which does not advertise masking capability despite implementing it. Even worse the chip comes out of reset with all MSI entries masked, which due to the missing masking capability never get unmasked. - Move the check which prevents accessing the MSI[X] masking for XEN back into the low level accessors. The recent consolidation missed that these accessors can be invoked from places which do not have that check which broke XEN. Move them back to he original place instead of sprinkling tons of these checks all over the code" * tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: of/irq: Don't ignore interrupt-controller when interrupt-map failed irqchip/sifive-plic: Fixup EOI failed when masked irqchip/csky-mpintc: Fixup mask/unmask implementation PCI/MSI: Destroy sysfs before freeing entries PCI: Add MSI masking quirk for Nvidia ION AHCI PCI/MSI: Deal with devices lying about their MSI mask capability PCI/MSI: Move non-mask check back into low level accessors -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 static call update from Thomas Gleixner: "A single fix for static calls to make the trampoline patching more robust by placing explicit signature bytes after the call trampoline to prevent patching random other jumps like the CFI jump table entries" * tag 'locking-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: static_call,x86: Robustify trampoline patching
-
