- 10 Aug, 2021 9 commits
-
-
Kuogee Hsieh authored
Initialize both pre-emphasis and voltage swing level to 0 before start link training and do not end link training until video is ready to reduce the period between end of link training and video start to meet Link Layer CTS requirement. Some dongle main link symbol may become unlocked again if host did not end link training soon enough after completion of link training 2. Host have to re train main link if loss of symbol locked detected before end link training so that the coming video stream can be transmitted to sink properly. This fixes Link Layer CTS cases 4.3.2.1, 4.3.2.2, 4.3.2.3 and 4.3.2.4. Changes in v3: -- merge retrain link if loss of symbol locked happen into this patch -- replace dp_ctrl_loss_symbol_lock() with dp_ctrl_channel_eq_ok() Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-7-git-send-email-khsieh@codeaurora.orgSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
Response with correct edid checksum saved at connector after corrupted edid checksum read. This fixes Link Layer CTS cases 4.2.2.3, 4.2.2.6. Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-6-git-send-email-khsieh@codeaurora.orgSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
Remove special handling of replug interrupt and instead treat replug event as a sequential unplug followed by a plugin event. This is needed to meet the requirements of DP Link Layer CTS test case 4.2.1.3. Changes in V2: -- add fixes statement Changes in V3: -- delete EV_HPD_REPLUG_INT Fixes: f21c8a27 ("drm/msm/dp: handle irq_hpd with sink_count = 0 correctly") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-5-git-send-email-khsieh@codeaurora.orgSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
Aux hardware calibration sequence requires resetting the aux controller in order for the new setting to take effect. However resetting the AUX controller will also clear HPD interrupt status which may accidentally cause pending unplug interrupt to get lost. Therefore reset aux controller only when link is in connection state when dp_aux_cmd_fifo_tx() fail. This fixes Link Layer CTS cases 4.2.1.1 and 4.2.1.2. Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-4-git-send-email-khsieh@codeaurora.orgSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
Reduce link rate and re start link training if link training 1 failed due to loss of clock recovery done to fix Link Layer CTS case 4.3.1.7. Also only update voltage and pre-emphasis swing level after link training started to fix Link Layer CTS case 4.3.1.6. Changes in V2: -- replaced cr_status with link_status[DP_LINK_STATUS_SIZE] -- replaced dp_ctrl_any_lane_cr_done() with dp_ctrl_colco_recovery_any_ok() -- replaced dp_ctrl_any_ane_cr_lose() with !drm_dp_clock_recovery_ok() Changes in V3: -- return failed if lane_count <= 1 Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-3-git-send-email-khsieh@codeaurora.org [remove unused cr_status variable] Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
DP cable should always connect to DPU during the entire PHY compliance testing run. Since DP PHY compliance test is executed at irq_hpd event context, dp_ctrl_off_link_stream() should be used instead of dp_ctrl_off(). dp_ctrl_off() is used for unplug event which is triggered when DP cable is dis connected. Changes in V2: -- add fixes statement Fixes: f21c8a27 ("drm/msm/dp: handle irq_hpd with sink_count = 0 correctly") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1628196295-7382-2-git-send-email-khsieh@codeaurora.orgSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Christophe JAILLET authored
'of_find_device_by_node()' takes a reference that must be released when not needed anymore. This is expected to be done in 'dsi_destroy()'. However, there are 2 issues in 'dsi_get_phy()'. First, if 'of_find_device_by_node()' succeeds but 'platform_get_drvdata()' returns NULL, 'msm_dsi->phy_dev' will still be NULL, and the reference won't be released in 'dsi_destroy()'. Secondly, as 'of_find_device_by_node()' already takes a reference, there is no need for an additional 'get_device()'. Move the assignment to 'msm_dsi->phy_dev' a few lines above and remove the unneeded 'get_device()' to solve both issues. Fixes: ec31abf6 ("drm/msm/dsi: Separate PHY to another platform device") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/f15bc57648a00e7c99f943903468a04639d50596.1628241097.git.christophe.jaillet@wanadoo.frSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Rob Clark authored
This check is really about which SQE firmware, rather than which GPU. Rework to match minimum version based on firmware name, so it doesn't need to be updated when adding additional GPUs using the same fw. Signed-off-by: Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20210807163019.379003-2-robdclark@gmail.comSigned-off-by: Rob Clark <robdclark@chromium.org>
-
Rob Clark authored
Combine adreno_is_a640() and adreno_is_a680(). Signed-off-by: Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20210807163019.379003-1-robdclark@gmail.comSigned-off-by: Rob Clark <robdclark@chromium.org>
-
- 07 Aug, 2021 31 commits
-
-
Dmitry Baryshkov authored
Restore the assgined-clocks and assigned-clock-parents properties that were lost during the txt -> YAML conversion. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210709210729.953114-2-dmitry.baryshkov@linaro.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
dpu_hw_ctl_clear_all_blendstages() clears settings for the few first LMs instead of mixers actually used for the CTL. Change it to clear necessary data, using provided mixer ids. Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210704230519.4081467-1-dmitry.baryshkov@linaro.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Add support for alpha blending properties. Setup the plane blend state according to those properties. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210628191958.2754731-1-dmitry.baryshkov@linaro.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Kuogee Hsieh authored
Currently at dp_pm_resume() is_connected state is decided base on hpd connection status only. This will put is_connected in wrongly "true" state at the scenario that dongle attached to DUT but without hmdi cable connecting to it. Fix this problem by adding read sink count from dongle and decided is_connected state base on both sink count and hpd connection status. Changes in v2: -- remove dp_get_sink_count() cand call drm_dp_read_sink_count() Changes in v3: -- delete status local variable from dp_pm_resume() Changes in v4: -- delete un necessary comment at dp_pm_resume() Fixes: d9aa6571 ("drm/msm/dp: check sink_count before update is_connected status") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Link: https://lore.kernel.org/r/1628092261-32346-1-git-send-email-khsieh@codeaurora.orgTested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Kalyan Thota authored
Add safe lut configuration for all the targets in dpu driver as per QOS recommendation. Issue reported on SC7280: With wait-for-safe feature in smmu enabled, RT client buffer levels are checked to be safe before smmu invalidation. Since display was always set to unsafe it was delaying the invalidaiton process thus impacting the performance on NRT clients such as eMMC and NVMe. Validated this change on SC7280, With this change eMMC performance has improved significantly. Changes in v2: - Add fixes tag (Sai) - CC stable kernel (Dimtry) Changes in v3: - Correct fixes tag with appropriate hash (stephen) - Resend patch adding reviewed by tag - Resend patch adding correct format for pushing into stable tree (Greg) Fixes: 591e34a0 ("drm/msm/disp/dpu1: add support for display for SC7280 target") Cc: stable@vger.kernel.org Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> (sc7280, sc7180) Link: https://lore.kernel.org/r/1628070028-2616-1-git-send-email-kalyan_t@codeaurora.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Souptick Joarder authored
Kernel test roobot throws below warning -> drivers/gpu/drm/msm/dp/dp_display.c:1017:21: warning: variable 'drm' set but not used [-Wunused-but-set-variable] Removed unused variable drm. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Link: https://lore.kernel.org/r/20210709024834.29680-1-jrdr.linux@gmail.comReviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Konrad Dybcio authored
VDDA is not present and the specified load value is wrong. Fix it. Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20210728222057.52641-1-konrad.dybcio@somainline.orgReviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Guo Zhengkui authored
Remove a repeated "#include <linux/debugfs.h>" in line 19 of the original file. Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com> Link: https://lore.kernel.org/r/20210729030140.99500-1-guozhengkui@vivo.comSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Maitreyee Rao authored
Add trace points across the MSM DP driver to help debug interop issues. Changes in v2: - Got rid of redundant log messages. - Added %#x instead of 0x%x wherever required. - Got rid of __func__ calls in debug messages. - Added newline wherever missing. Changes in v3: - Got rid of redundant log messages. - Unstuck colon from printf specifier in various places. Changes in v4: - Changed goto statement and used if else-if Changes in v5: - Changed if else if statement, to not overwrite the ret variable multiple times. Changes in v6: - Changed a wrong log message. Signed-off-by: Maitreyee Rao <maitreye@codeaurora.org> Link: https://lore.kernel.org/r/1627346298-11528-1-git-send-email-maitreye@codeaurora.orgReviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
set_encoder_mode callback is completely unused now. Drop it from msm_kms_func(). Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-8-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
None of the display drivers now implement set_encoder_mode callback. Stop calling it from the modeset init code. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-7-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
None of the display drivers now implement set_encoder_mode callback. Stop calling it from the modeset init code. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-6-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Move a call to mdp5_encoder_set_intf_mode() after msm_dsi_modeset_init(), removing set_encoder_mode callback. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-5-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Move setting up encoders from set_encoder_mode to _dpu_kms_initialize_dsi() / _dpu_kms_initialize_displayport(). This allows us to support not only "single DSI" and "bonded DSI" but also "two independent DSI" configurations. In future this would also help adding support for multiple DP connectors. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-4-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Add three helper functions to be used by display drivers for setting up encoders. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-3-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
We are preparing to support two independent DSI hosts in the DSI/DPU code. To remove possible confusion (as both configurations can be referenced as dual DSI) let's rename old "dual DSI" (two DSI hosts driving single device, with clocks being locked) to "bonded DSI". Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210717124016.316020-2-dmitry.baryshkov@linaro.orgReviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> [DB: add one extra hunk added by one previous patches] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Abhinav Kumar authored
During board bringups its useful to have a DSI test pattern generator to isolate a DPU vs a DSI issue and focus on the relevant hardware block. To facilitate this, add an API which triggers the DSI controller test pattern. The expected output is a rectangular checkered pattern. This has been validated on a single DSI video mode panel by calling it right after drm_panel_enable() which is also the ideal location to use this as the DSI host and the panel have been initialized by then. Further validation on dual DSI and command mode panel is pending. If there are any fix ups needed for those, it shall be applied on top of this change. Changes in v2: - generate the new dsi.xml.h and update the bitfield names Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/1626922232-29105-2-git-send-email-abhinavk@codeaurora.orgReviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Abhinav Kumar authored
Update the DSI controller header XML file to add registers and bitfields to support rectangular checkered pattern generator. Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/1626922232-29105-1-git-send-email-abhinavk@codeaurora.orgReviewed-by: Stephen Boyd <swboyd@chromium.org> [DB: removed headergen commit changes] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Rajeev Nandan authored
Add support for v2.5.0 DSI block in the SC7280 SoC. Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/1624365748-24224-4-git-send-email-rajeevny@codeaurora.orgReviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Rajeev Nandan authored
The SC7280 SoC uses the 7nm (V4.1) DSI PHY driver with different enable|disable regulator loads. Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/1624365748-24224-3-git-send-email-rajeevny@codeaurora.orgReviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Rajeev Nandan authored
The SC7280 SoC uses the 7nm (V4.1) DSI PHY driver. Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org> Link: https://lore.kernel.org/r/1624365748-24224-2-git-send-email-rajeevny@codeaurora.orgAcked-by: Rob Herring <robh+dt@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Instead of fetching shared timing through an extra function call, get them directly from msm_dsi_phy_enable. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210709210729.953114-9-dmitry.baryshkov@linaro.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
Use of_device_get_match-data() instead of of_match_node(). Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210709210729.953114-8-dmitry.baryshkov@linaro.orgSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Stephen Boyd authored
Add some missing newlines to the various DRM printks in this file. Noticed while looking at logs. While we're here unbreak quoted strings so grepping them is easier. Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210708065619.999199-1-swboyd@chromium.orgReviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
David Heidelberg authored
msm_atomic is doing vblank get/put's already, currently there no need to duplicate the effort in MDP4 Fix warning: ... WARNING: CPU: 3 PID: 79 at drivers/gpu/drm/drm_vblank.c:1194 drm_vblank_put+0x1cc/0x1d4 ... and multiple vblank time-outs: ... msm 5100000.mdp: vblank time out, crtc=1 ... Tested on Nexus 7 2013 (deb), LTS 5.10.50. Introduced by: 119ecb7f ("drm/msm/mdp4: request vblank during modeset") Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20210715060925.7880-1-david@ixit.czSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
David Heidelberg authored
Fixes if condition, which never worked inside mdp4_kms_init, since HW detection has been done later in mdp4_hw_init. Fixes: eb2b47bb ("drm/msm/mdp4: only use lut_clk on mdp4.2+") Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20210705231641.315804-2-david@ixit.czReviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
David Heidelberg authored
Inspired by MDP5 code. Also use DRM_DEV_INFO for MDP version as MDP5 does. Cosmetic change: uint32_t -> u32 - checkpatch suggestion. Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20210705231641.315804-1-david@ixit.czReviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Wei Li authored
When it fail to create crtc_event kthread, it just jump to err_msm_uninit, while the 'ret' is not updated. So assign the return code before that. Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Li <liwei391@huawei.com> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210705134302.315813-1-liwei391@huawei.comSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Dmitry Baryshkov authored
None of supported devies uses "gdsc" regulator for DSI. GDSC support is now implemented as a power domain. Drop old code and config handling gdsc regulator requesting and enabling. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210701000015.3347713-1-dmitry.baryshkov@linaro.orgReviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Jonathan Marek authored
Add the required changes to support 7nm pll/phy in CPHY mode. This adds a "qcom,dsi-phy-cphy-mode" property for the PHY node to enable the CPHY mode. Signed-off-by: Jonathan Marek <jonathan@marek.ca> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210617144349.28448-4-jonathan@marek.caSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-
Jonathan Marek authored
Document a new phy-type property which will be used to determine whether the phy should operate in D-PHY or C-PHY mode. Signed-off-by: Jonathan Marek <jonathan@marek.ca> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://lore.kernel.org/r/20210617144349.28448-3-jonathan@marek.caAcked-by: Rob Herring <robh@kernel.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
-