Instead of only parsing device tree properties let's switch to using
generic properties API so that the driver can also work on other platforms.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We do not have any users of platform data in the tree and all newer
platforms are either DT or ACPI, so let's drop handling of platform data.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver does not use irq gpio as gpio, but rather relies on I2C core or
board code to set up client's structure IRQ line, so let's stop trying to
locate the resource and parse it.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current/old gpio framework used doesn't properly listen to
ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
account these flags when setting gpio values.

Since the values being output were based on voltage and not logic they
change to reflect this difference. Also use gpiod_set_value_cansleep since
wake and reset pins can be provided by bus based io expanders.

Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
warning.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use managed resource functions devm_request_threaded_irq,
devm_inpute_allocate_device and devm_kzalloc to simplify error handling.
Also, remove use of input_unregister_device as input_register_device itself
handles it and works as resource managed function.

To be compatible with the change, various gotos are replaced with direct
returns, and unneeded labels are dropped. With these changes remove
ad714x_remove and corresponding calls of it as they are now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since commit 81e8f2bc (Input: imx_keypad - add pm suspend and resume
support) the imx_keypad driver supports power management, so let's remove
the obsolete comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Freescale i.MX6UL contains a internal touchscreen controller,
this patch add a driver to support this controller.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Colibri Vybrid VF50 module supports 4-wire touchscreens using
FETs and ADC inputs. This driver uses the IIO consumer interface
and relies on the vf610_adc driver based on the IIO framework.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Nowadays the machines without i8042 controller is popular, and no need
to print "No controller found" message in the error log level, which
annoys at booting in quiet mode.  Let's lower it info level.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We've got bug reports showing the old systemd-logind (at least
system-210) aborting unexpectedly, and this turned out to be because
of an invalid error code from close() call to evdev devices.  close()
is supposed to return only either EINTR or EBADFD, while the device
returned ENODEV.  logind was overreacting to it and decided to kill
itself when an unexpected error code was received.  What a tragedy.

The bad error code comes from flush fops, and actually evdev_flush()
returns ENODEV when device is disconnected or client's access to it is
revoked. But in these cases the fact that flush did not actually happen is
not an error, but rather normal behavior. For non-disconnected devices
result of flush is also not that interesting as there is no potential of
data loss and even if it fails application has no way of handling the
error. Because of that we are better off always returning success from
evdev_flush().

Also returning EINTR from flush()/close() is discouraged (as it is not
clear how application should handle this error), so let's stop taking
evdev->mutex interruptibly.

Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=939834
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 23 inch device found in Chrome project buddy requires 9.2~10.5 seconds
to complete calibration. Let's increase calibration timeout to 12 seconds
to give the device enough time.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The drivers have a I2C device ID table that is used to create the module
aliases and also "cyttsp" and "cyttsp4" are not supported I2C device IDs
so these module aliases are never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This ACPI ID present in the DSDT of the ASUS E202SA laptop.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver is a platform driver and not a I2C driver so its modalias
should be exported with MODULE_DEVICE_TABLE(platform,...) instead of
MODULE_DEVICE_TABLE(i2c,...).

Also, remove the unnecessary MODULE_ALIAS("platform:max8997-haptic")
now that the correct module alias is created.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Search for "vaildpage_count" and replace with "validpage_count".
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.

One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Reviewed-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When trying to disable a key that is not supported by the device we should
report error, not do nothing and report success:

root@yocto:/sys/devices/soc0/gpio-keys# cat keys
114-116
root@yocto:/sys/devices/soc0/gpio-keys# echo 77 > keys
root@yocto:/sys/devices/soc0/gpio-keys#

We want 'echo 77 > keys' to report an error, but silence to give us an
illusion that all is 'ok'.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Propagate error code on failure, or upper layers will be confused by
returned 0 (success) code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

I have a static checker that complains when we check for an upper bound
but don't have a corresponding check for a lower bound.  With this code,
the upper bound check seems not really required, so it is not a bug to
leave the lower bound check out as well.  But let's silence the warning
by making these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of custom zhenhua_bitreverse() let's use generic bitrev8().
Signed-off-by: Yalin Wang <yalin.wang2010@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ChromeOS EC keyboard driver config depends on CROS_EC_PROTO but
MFD_CROS_EC selects CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.

Since the platform device that is matched with the keyboard driver
is registered by the ChromeOS EC mfd driver, KEYBOARD_CROS_EC really
should depend on MFD_CROS_EC. And because this config option selects
CROS_EC_PROTO, that dependency is met as well. So make the driver
to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Several cap11xx variants have LEDs that be can be controlled; let's plug
the driver into the LED subsystem.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Flags are now mandatory for devm_gpiod_get(). So let's use proper flag
to configure gpio for output instead of doing this by hand.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[Dmitry: GPIOD_ASIS -> GPIOD_OUT_LOW]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Elan touchscreen controllers use two power supplies, vcc33 and vccio,
and we need to enable them before trying to access the device. On X86
firmware usually does this, but on ARM it is usually left to the kernel.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Do not emit EV_SYN/SYN_REPORT on suspend if there were no keys that are
still pressed as we are suspending the device (and in all other cases when
input core is forcibly releasing keys via input_dev_release_keys() call).
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If the device is in idle mode and is in the middle of a scan it may not
have a chance to react to the reset and then IAP commands within required
time interval and firmware update may fail. Let's bring the device out of
idle mode before attempting to reset it so that the scan period is smaller
and thus it can react to the command quicker.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This indicates the device coordinates should be directly mapped to screen.
This is valid since scaling/flipping/rotation should be done by configuring
the MXT device.

It also flags to Android using INPUT_PROP_DIRECT that the device should be
treated as a touch screen by default, and removes the necessity for a
default IDC file.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The CHG/interrupt line is momentarily set (approximately 100 ms) as an
input after power-up or reset for diagnostic purposes. This may cause
spurious interrupts, so disable interrupt handler during this period.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use function rather than loop, define np to reduce wrapping.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is
still available and suspend/resume assume
input_dev is not NULL. To fix this issue, we add a check if (!input_dev).
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>