The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The Shared Memory Pool (SMP) has its own limitation, features and
state. Some examples are:
 - the number of Memory Macro Block (MMB) and their size
 - the number of lines that can be fetched
 - the state of MMB currently allocated
 - the computation of number of blocks required per plane
 - client IDs ...

In order to avoid private data to be overwritten by other modules,
let's make these private to the SMP module.

Some of these depend on the hardware configuration, let's add them
to the mdp5_config struct.

In some hw configurations, some MMBs are statically tied to RGB
pipes and cannot be re-allocated dynamically. This change
introduces the concept of MMB static usage and makes sure that
dynamic MMB requests are dimensioned accordingly.

A note on passing a pipe pointer, instead of client IDs:
Client IDs are SMP-related information. Passing PIPE information
to SMP lets SMP module to find out which SMP client(s) are used.
This allows the SMP module to access the PIPE pointer, which can
be used for FIFO watermark configuration.
By the way, even though REG_MDP5_PIPE_REQPRIO_FIFO_WM_* registers
are part of the PIPE registers, their functionality is to reflect
the behavior of the SMP block. These registers access is now
restricted to the SMP module.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

A left-over from prior to component framework.  The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways.  These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: Rob Clark <robdclark@gmail.com>

The core clock rate depends on the hw configuration. Once we have
read the hardware revision, we can set the core clock to its
maximum value.
Before then, the clock is set at a rate supported by all MDP5
revisions.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block.  In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5.  When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal.  When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:

	mdp: qcom,mdss_mdp@fd900000 {
		compatible = "qcom,mdss_mdp";
		interrupt-controller;
		#interrupt-cells = <1>;
		...
	};

	hdmi: qcom,hdmi_tx@fd922100 {
		compatible = "qcom,hdmi-tx-8074";
		interrupt-parent = <&mdp>;
		interrupts = <8 0>;   /* MDP5_HW_INTR_STATUS.INTR_HDMI */
		...
	};

There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block.  So
you must not use threaded irq handlers in the child.  I'm not sure
if there is a better way to deal with that.
Signed-off-by: Rob Clark <robdclark@gmail.com>

- More CI dpm fixes
- Initial DPM fan control for SI/CI (disabled by default)
- GPUVM multi-ring efficiency improvements
- Some cursor fixes

* 'drm-next-3.19' of git://people.freedesktop.org/~agd5f/linux: (22 commits)
  drm/radeon: update the VM after setting BO address v4
  drm/radeon: sync PT updates as shared v2
  drm/radeon: sync PD updates as shared
  drm/radeon: fence BO_VAs manually
  drm/radeon: use one VMID for each ring
  drm/radeon: track VM update fences separately
  drm/radeon: fence PT updates manually v2
  drm/radeon: split semaphore and sync object handling v2
  drm/radeon: remove unnecessary VM syncs
  drm/radeon: stop re-reserving the BO in radeon_vm_bo_set_addr
  drm/radeon: rework vm_flush parameters
  drm/radeon/ci: disable needless sclk changes
  drm/radeon/ci: force pcie level before sclk and mclk
  drm/radeon/ci: use different smc command for pcie dpm
  drm/radeon/ci: apply disp voltage changes before clk changes
  drm/radeon: fix PCC debugging message for CI DPM
  drm/radeon/dpm: add thermal dpm support for CI
  drm/radeon/dpm: add smc fan control for CI (v2)
  drm/radeon/dpm: add smc fan control for SI (v2)
  drm/radeon: work around a hw bug in MGCG on CIK
  ...

The vfree() function performes also input parameter validation. Thus the test
around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The vunmap() function performes also input parameter validation. Thus the test
around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The drm_fbdev_cma_hotplug_event() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is an oversight from

commit f52b69f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Nov 19 18:38:08 2014 +0100

    drm/atomic: Don't overrun the connector array when hotplugging

Cc: Dave Airlie <airlied@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

It happens on occasion that developers of generic user-space applications
abuse the dumb buffer API to get hold of drm buffers that they can both
mmap() and use for GPU acceleration, using the assumptions that dumb buffers
and buffers available for GPU are
a) The same type and can be aribtrarily type-casted.
b) fully coherent.

This patch makes the most widely used drivers warn nicely when that happens,
the next step will be to fail.

v2: Move drmP.h changes to drm_gem.h. Fix Radeon dumb mmap breakage.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This way the necessary VM update is kicked off immediately
if all BOs involved are in GPU accessible memory.

v2: fix vm lock
v3: immediately update unmaps as well
v4: use drm_free_large instead of kfree
Tested-by: Kai Wasserbäch <kai@dev.carbon-project.org>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Only invalidating PTEs needs to be executed synchronized to using the PT.

v2: fix sync to uses
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We never invalidate PD entries and making them valid can
run with other users in parallel.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This allows us to finally remove the VM fence and
so allow concurrent use of it from different engines.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use multiple VMIDs for each VM, one for each ring. That allows
us to execute flushes separately on each ring, still not ideal
cause in a lot of cases rings can share IDs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Note for each fence if it's a VM page table update or not. This allows
us to determine the last VM update in a sync object and so to figure
out if we need to flush the TLB or not.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This allows us to add the real execution fence as shared.

v2: fix typo
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Previously we just allocated space for four hardware semaphores
in each software semaphore object. Make software semaphore objects
represent only one hardware semaphore address again by splitting
the sync code into it's own object.

v2: fix typo in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The PD/PTs reservation object now contains everything needed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

That's useless when all callers drop the reservation
immediately after calling the function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use ring structure instead of index and provide vm_id and pd_addr separately.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The current code always reprogrammed the sclk levels,
but we don't currently handle disp sclk requirements
so just skip it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Preferred ordering.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use unforce levels rather than enable mask instruction.
This is the preferred method.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Apply voltage changes for displays before changing clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add missing newline and print the bad gpio shift.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Not currently used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable smc fan control for CI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add additional fan setup, rpm control

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable smc fan control for SI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add rpm controls

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Always need to set bit 0 of RLC_CGTT_MGCG_OVERRIDE
to avoid unreliable doorbell updates in some cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

No functional change.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge AMDKFD it seems clean enough.
* 'amdkfd-v6' of git://people.freedesktop.org/~gabbayo/linux: (29 commits)
  amdkfd: Implement the Get Version IOCTL
  amdkfd: Implement the Get Process Aperture IOCTL
  amdkfd: Implement the Get Clock Counters IOCTL
  amdkfd: Implement the Set Memory Policy IOCTL
  amdkfd: Implement the create/destroy/update queue IOCTLs
  amdkfd: Add interrupt handling module
  amdkfd: Add device queue manager module
  amdkfd: Add process queue manager module
  amdkfd: Add packet manager module
  amdkfd: Add module parameter of scheduling policy
  amdkfd: Add kernel queue module
  amdkfd: Add mqd_manager module
  amdkfd: Add queue module
  amdkfd: Add binding/unbinding calls to amd_iommu driver
  amdkfd: Add basic modules to amdkfd
  amdkfd: Add topology module to amdkfd
  amdkfd: Add amdkfd skeleton driver
  amdkfd: Add IOCTL set definitions of amdkfd
  Update MAINTAINERS and CREDITS files with amdkfd info
  drm/radeon: Add radeon <--> amdkfd interface
  ...

This patch allows framebuffers for cirrus to be created with
32bpp pixel formats provided that they do not violate certain
restrictions of the cirrus hardware.

v2: Use pci resource length for vram size.
Signed-off-by: Zach Reizner <zachr@google.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Only importing an FD to a handle is currently supported on UDL,
but the exporting functionality is equally useful.
Signed-off-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

By default set udl_gem_object as cacheable, but set WC flag when attaching
dmabuf. In udl_gem_mmap() update cache attributes based on the flags, similar
to exynos_drm_gem_mmap().
Signed-off-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Before this patch, cirrus_device_init could have failed while
cirrus_mm_init succeeded and the driver would have reported overall
success on load. This patch causes cirrus_device_init to return on
the first error encountered.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Oversight from my kerneldoc cleanup when doing the original atomic
helper series - I've only applied this clarification to the modeset
related helpers, and not the plane update code. Remedy this asap.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>